User Manual MIO-5270
Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Technical Support and Assistance 1. 2. Visit the Advantech web site at www.advantech.com where you can find the latest information about the product. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
Packing List Before setting up the system, check that the items listed below are included and in good condition. If any item does not accord with the table, please contact your dealer immediately.
Optional MIOe Module Part Number Description MIOe-210-D6A1E 4x RS232/422/485 2x RS422/485 with DSUB connector, 8-bit GPIO MIOe-210-W6A1E 4x RS232/422/485 2x RS422/485 with Wafer connector, 8-bit GPIO MIOe-220-L3A1E 3 x GbE with RJ45 connector MIOe-220-B3A1E 3 x GbE with RJ45 connector through PCIE switch MIOe-230-L0A1E* Displayport to 48-bit LVDS MIOe-230-D0A1E* Displayport to Ext. Displayport *MIOe-230 compatibility is optional by request.
14. If one of the following situations arises, get the equipment checked by service personnel: The power cord or plug is damaged. Liquid has penetrated into the equipment. The equipment has been exposed to moisture. The equipment does not work well, or you cannot get it to work according to the user's manual. The equipment has been dropped and damaged. The equipment has obvious signs of breakage. 15.
MIO-5270 User Manual viii
Contents Chapter Chapter 1 General Information ............................1 1.1 1.2 1.3 Introduction ............................................................................................... 2 Product Specifications............................................................................... 2 Chipset ...................................................................................................... 3 1.3.1 Functional Specifications ..........................................................
Appendix B System Assignment.......................... 57 B.1 System I/O Ports..................................................................................... 58 Table B.1: System I/O Ports ...................................................... 58 1st MB memory map............................................................................... 58 Table B.2: 1st MB memory map ................................................ 58 Interrupt assignments .....................................................
Chapter 1 1 General Information
1.1 Introduction CPU: AMD G-series eOntario – T56N (Dual Core 1.65GHz) on MIO-5270D-S6A1E – T40E (Dual Core 1.0GHz) on MIO-5270D-S0A1E – T40R (Single Core 1.0GHz) on MIO-5270S-S0A1E MIO Compact SBC form factor standard One 204-pin SODIMM DDR3 up to 4G – T56N: DDR3 1333 MHz – T40E/T40R: DDR3 1066 MHz Dual Independent Display: VGA+LVDS, VGA+HDMI, HDMI+LVDS 6 x USB 2.
Speed GbE 10/100/1000 Mbps Chipset Realtek RTL8111E- VB-GR (GbE1, GbE2) Ethernet Interface Fully compliant with IEEE 802.3, IEEE 802.3u, IEEE 802.
Video Accelerator Display Dual independent display 2D Acceleration 3D Acceleration – Fully DirectX® 11 compliant, including full speed 32-bit floating point per component operations – Support for OpenCL™ 1.0 – Support for OpenGL® 3.2 and 2.1 Motion Video Acceleration – Supports DVD, Blu-ray*, and SDTV/HDTV content playback with the lowest CPU usage – H.
Chapter 1 1.3.1.3 iManager iManager Supported SMBus Supported GPIO 8-bit GPIO Watchdog timer Multi Level WDT (set by Advantech iManager) Programmable 1-255 sec / min Hardware monitor CPU Temperature / input Current / input Voltage Power saving Deep sleep S5 mode / Smart Fan / Back light control FAN 1. Smart FAN Support. 2. Programmable automatic fan monitor based on temperature. 3.
1.3.3 Electrical Specifications 1.3.3.1 Power Supply Voltage Power Type Single 12V DC power in Power Supply Voltage Single 12V ± 10% 1.3.3.2 Power Supply Current Test Condition: Add-in Card - None PCIe Mini Card - None Memory - DDR3 SODIMM 4GB HDD - 3.5" WD 80GB SATA2 *1 KeyBoard/Mouse - USB Display - VGA Power Consumption (A or mA) Condition Voltage/ Power on DOS Idle Win. Idle Condition Boot Procedure Mode Mode Win. HCT12 S3 (10minutes) S5 MIO-5270D-S6A1E +12V 1.65 1.45 0.65 1.
Chapter 2 2 Hardware Installation
This chapter explains the setup procedures of the MIO-5270 A1 hardware, including instructions on setting jumpers and connecting peripherals, switches, indicators and mechanical drawings. Be sure to read all safety precautions before you begin the installation procedure. 2.1 Jumpers 2.1.1 Jumper List J1 Clear CMOS J2 Auto Power On Setting J3 LCD Power J5 COM2 Setting 2.1.2 Jumper Settings J1 Clear CMOS Part Number 1653003101 Footprint HD_3x1P_79_D Description PIN HEADER 3x1P 2.
LCD Power Part Number 1653003201 Footprint HD_3x2P_79_D Description PIN HEADER 3*2P 180D(M) 2.0mm DIP SQUARE WO/Pb Setting Function +3.3V (3-5) +5V (3-4) +12V J5 COM2 Setting Part Number 1653003260 Footprint HD_3x2P_79 Description PIN HEADER 3x2P 2.0mm 180D(M) SMD 21N22050 Setting Function (1-2)* RS232 (3-4) RS485 (5-6) RS422 2.1.3 Jumper Description Cards can be configured by setting jumpers. A jumper is a metal bridge used to close an electric circuit.
The jumper settings are schematically depicted in this manual as follows. A pair of needle-nose pliers may be helpful when working with jumpers. If you have any doubts about the best hardware configuration for your application, contact your local distributor or sales representative before you make any changes. Warning! To avoid damaging the computer, always turn off the power supply before setting jumpers to clear CMOS. Before turning on the power supply, set the jumper back to 3.0 V Battery On. 2.
Chapter 2 2.3 Mechanical 2.3.1 Jumper and Connector Location CN2 CN7 CN5 CN6 CN4 CN3 CN1 CN12 FAN1 ESBC Jensen. Li CN18 CN19 CN20 CN17 CN23 J3 CN22 Power LED CN13 CN14 Figure 2.
CN24 CN8 J5 CN25 Audio GPIO J5 COM 1/2 COM 3/4 CN26 CN28 CN29 CN31 BIOS MIOe PCIe Mini card CFast Socket Figure 2.
Chapter 2 2.3.2 Board Dimensions Hardware Installation Figure 2.3 Board Dimension Layout (Component Side) Figure 2.
139,50 130,81 111,92 76,09 45,58 26,30 39,62 4,20 18,54 6,00 5,14 7,90 75,69 112,82 Figure 2.
Chapter 3 BIOS Settings 3
AMIBIOS has been integrated into many motherboards for over a decade. With the AMIBIOS setup program, you can modify BIOS settings and control the various system features. This chapter describes the basic navigation of the MIO-5270 BIOS setup screens. AMI’s BIOS ROM has a built-in Setup program that allows users to modify the basic system configuration. This information is stored in battery-backed CMOS so it retains the Setup information when the power is turned off. 3.
When you first enter the BIOS Setup Utility, you will enter the Main setup screen. You can always return to the Main setup screen by selecting the Main tab. There are two Main Setup options. They are described in this section. The Main BIOS Setup screen is shown below. Chapter 3 3.2 Main Setup BIOS Settings The Main BIOS setup screen has two main frames. The left frame displays all the options that can be configured. Grayed-out options cannot be configured; options in blue can.
3.3 Advanced BIOS Features Setup Select the Advanced tab from the MIO-5270 setup screen to enter the Advanced BIOS Setup screen. You can select any of the items in the left frame of the screen, such as CPU Configuration, to go to the sub menu for that item. You can display an Advanced BIOS Setup option by highlighting it using the keys. All Advanced BIOS Setup options are described in this section. The Advanced BIOS Setup screens are shown below. The sub menus are described on the following pages.
Chapter 3 3.3.1 PCI Subsystem Settings Configuration BIOS Settings PCI ROM Priority This item allows you to select the EFI ROM and Legacy ROM priority. PCI Latency Timer This item allows you to select the 32/64/96/128/160/192/224/248 PCI bus clocks. VGA Palette Snoop Enabled or disable VGA palette registers snooping. PERR# Generation Enabled or disable PCI device to generation PERR#. SERR# Generation Enabled or disable PCI device to generation SERR#.
3.3.2 ACPI Settings Configuration ACPI Sleep State Select the ACPI state used for system suspend. S3 Video Repost Enable or disable video repost.
Chapter 3 3.3.3 CPU Configuration BIOS Settings Limit CPUID Maximum This item allows you to disable for Windows XP. PPS Support This item allows you to enable or disable the ACPI _PPC, _PSS, and _PCT objects. PSTATE Adjustment This item allows you to provide P-state level. PPC Adjustment This item allows you to provide _PPC object. NX Mode This item allows you to enable or disable the No-execute page protection function.
3.3.4 IDE Configuration IDE Configuration Display SATA Port0 / SATA Port1 / SATA Port2 / SATA Port3 information. 3.3.
3.3.6 Embedded Controller Configuration Embedded Controller Configuration EC iManager WatchDog IRQ This item allows you to select IRQ number for watchdog. EC Power Saving Mode This item allows you to select normal or deep sleep power saving. EC iManager Smart FAN This item allows you to enable or disable EC smart FAN control. Temperature & Voltage show CPU Temperature VBAT / +V5SB / +Vin / Vcore / Current Display current.
Fan Speed show Display Fan Speed RPM. Backlight Enable Polarity This item allows you to select polarity for PWM or DC mode. EC Watch Dog Function This item allows you to select the watchdog timer. 3.3.7 Super I/O Configuration Serial Port1 / Port2 / Port3 / Port4 address This item allows you to select serial port1 ~ port4 of base addresses. Serial Port1 / Port2 / Port3 / Port4 IRQ This item allows you to select serial port1 ~ port4 of IRQ.
Chapter 3 3.4 Chipset Configuration BIOS Settings North Bridge Detail for North Bridge items. Display Config Select Detail for display items. South Bridge Detail for South Bridge items.
3.4.1 North Bridge Configuration GFX Configuration Details of LAN1/LAN2, and PSPP Policy items. Memory Configuration Details of Bank Interleaving, IOMMU Mode, and Memory Clock items. Node 0 Information Details of memory information.
Chapter 3 3.4.2 Display Configuration Select BIOS Settings LVDS* This item allows you to enable or disable LVDS function. HDMI This item allows you to enable or disable HDMI function. * LVDS setting of customized define, please refer to the document on CD-ROM: "Chrontel EEPROM Adjust SOP.
3.4.3 South Bridge SB SATA Configuration Options for SATA configuration. SB USB Configuration Options for SB USB configuration. SB GPP Port Configuration Options for SB GPP port configuration. SB HD Azalia Configuration Options for SB HD Azalia. MINI Card/M-SATA This item allows you to select MINI card or M-SATA.
Chapter 3 3.5 Boot Configuration BIOS Settings Setup Prompt Timeout This item allows you to change number of seconds to wait for setup activation key. Bootup NumLock State Select the Power-on state for Numlock. Quiet Boot If this option is set to Disabled, the BIOS displays normal POST messages. If Enabled, an OEM Logo is shown instead of POST messages. Fast Boot This item allows BIOS to skip certain tests while booting. This will decrease the time needed to boot the system.
3.6 Security Configuration Select Security Setup from the MIO-5270 Setup main BIOS setup menu. All Security Setup options, such as password protection and virus protection are described in this section.
Chapter 3 3.7 Save & Exit BIOS Settings Save Changes and Exit This item allows you to exit system setup after saving changes. Discard Changes and Exit This item allows you to exit system setup without saving any changes. Save Changes and Reset This item allows you to reset the system after saving the changes. Discard Changes and Reset This item allows you to rest system setup without saving any changes.
MIO-5270 User Manual 32
Chapter 4 MIOe Installation 4
MIO compact form factor SBC is a new generation SBC design with a variety of mechanical improvements. Here is the quick installation guide to introduce our thermal design and MIOe module installation. Quick Installation guide: 1. There is a Heatsink / Cooler in the white box inside the package. Please be careful, remove the release paper from the thermal pad before installation. Removing the release paper 2. 3.
Appendix A A Pin Assignments
CN1 Power Switch Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 2.0mm 180D(M) DIP A2001WV2-2P Pin Pin Name 1 PSIN 2 GND CN2 Inverter Power Output Part Number 1655000453 Footprint WHL5V-2M-24W1140 Description WAFER BOX 2.0mm 5P 180D(M) DIP WO/Pb JIH VEI Pin Pin Name 1 +12V 2 GND 3 ENABKL 4 VBR 5 +5V CN3 Reset Part Number 1655302020 Footprint WF_2P_79_BOX_R1_D Description WAFER BOX 2P 2.
SATA Power Part Number 1655001154 Footprint WF_4P_98_BOX_R1_D Description WAFER BOX 4P 2.50mm 180D(M) DIP 24W1170-04S10-01 Pin Pin Name 1 +5V 2 GND 3 GND 4 +12V CN5 SATA 1 Part Number 1654007578 Footprint SATA_7P_WATF-07DBN6SB1U Description Serial ATA 7P 1.
CN6 SATA 2 Part Number 1654007578 Footprint SATA_7P_WATF-07DBN6SB1U Description Serial ATA 7P 1.27mm 180D(M) SMD WATF-07DBN6SB1U Pin Pin Name 1 GND 2 TX+ 3 TX- 4 GND 5 RX- 6 RX+ 7 GND CN7 RS422/485 Part Number 1655304032 Footprint WF_5P_49_BOX_85205 Description WAFER 5P 1.
GPIO Part Number 1653004099 Footprint HD_5x2P_79_23N685B-10M10 Description BOX HEADER 5x2P 2.
CN10 DDR3 SODIMM Socket Part Number 1651001648 Footprint DDR3_204P_2-2013311-1 Description DDR3 SODIMM H=9.
Internal USB Part Number 1653005260 Footprint HD_5x2P_79_N10 Description PIN HEADER 2x5P 2.0mm 180D(M) SMD 21N22050 Pin Pin Name 1 +5V 2 +5V 3 A_D- 4 B_D- 5 A_D+ 6 B_D+ 7 GND 8 GND 9 GND CN13 SMBus Part Number 1655904020 Footprint FPC4V-125M Description WAFER 4P 1.
CN14 LAN Part Number 1652003274 Footprint RJ45_28P_RTB-19GB9J1A Description PHONE JACK RJ45 28P DIP RTB-19GB9J1A Pin Pin Name 1 TX+(10/100),BI_DA+(GHz) 2 TX-(10/100),BI_DA-(GHz) 3 RX+(10/100),BI_DB+(GHz) 4 BI_DC+(GHz) 5 BI_DC-(GHz) 6 RX-(10/100),BI_DB-(GHz) 7 BI_DD+(GHz) 8 BI_DD-(GHz) CN17 48 bits LVDS Panel Part Number 1653920200 Footprint SPH20X2 Description B/B Conn. 40P 1.25mm 90D SMD DF13-40DP-1.25V Pin Pin Name 1 +3.3V, +5V or +12V 2 +3.
LVDS1_D2- 21 LVDS0_D2+ 22 LVDS1_D2+ 23 GND 24 GND 25 LVDS0_CLK- 26 LVDS1_CLK- 27 LVDS0_CLK+ 28 LVDS1_CLK+ 29 GND 30 GND 31 NC 32 NC 33 GND 34 GND 35 LVDS0_D3- 36 LVDS1_D3- 37 LVDS0_D3+ 38 LVDS1_D3+ 39 NC 40 NC Appendix A Pin Assignments 20 43 MIO-5270 User Manual
CN18 External USB Part Number 1654009513 Footprint USB_8P_UB1112C-8FDE-4F Description Pin Pin Name 1 +5V 2 D- 3 D+ 4 GND CN19 External USB Part Number 1654009513 Footprint USB_8P_UB1112C-8FDE-4F Description Pin Pin Name 1 +5V 2 D- 3 D+ 4 GND MIO-5270 User Manual 44
HDMI Part Number 1654009225 Footprint HDMI_19P_QJ51193-FFD4-7F Description HDMI Conn 19P 0.
CN22 12V Power Input Part Number 1655404090 Footprint WF_2x2P_165_BOX_RA_D_740SP Description ATX PWR CONN. 2x2P 4.2mm 180D(M) DIP 24W4310-04S Pin Pin Name 1 GND 2 GND 3 +12V 4 +12V CN23 VGA Part Number 1654000055 Footprint DBVGA-VF5MS Description D-SUB Conn.
Audio Part Number 1653004099 Footprint HD_5x2P_79_23N685B-10M10 Description BOX HEADER 5x2P 2.
19 GND 20 GND CN26 COM3/COM4 Part Number 1653004793 Footprint HD_10x2P_79_23N685B-20M10 Description Pin Pin Name 1 DCD3# 2 DSR3# 3 RXD3 4 RTS3# 5 TXD3 6 CTS3# 7 DTR3# 8 RI3# 9 GND 10 GND 11 DCD4# 12 DSR4# 13 RXD4 14 RTS4# 15 TXD4 16 CTS4# 17 DTR4# 18 RI4# 19 GND 20 GND MIO-5270 User Manual 48
MIOe Part Number 1654006235 Footprint BB_40x2P_32_1625x285_2HOLD Appendix A Pin Assignments CN28 Description Pin Pin Name 1 GND 2 GND 3 PCIE_RX0+ 4 PCIE_TX0+ 5 PCIE_RX0- 6 PCIE_TX0- 7 GND 8 GND 9 PCIE_RX1+ 10 PCIE_TX1+ 11 PCIE_RX1- 12 PCIE_TX1- 13 GND 14 GND 15 PCIE_RX2+ 16 PCIE_TX2+ 17 PCIE_RX2- 18 PCIE_TX2- 19 GND 20 GND 21 PCIE_RX3+ 22 PCIE_TX3+ 23 PCIE_RX3- 24 PCIE_TX3- 25 GND 26 GND 27 PCIE_CLK+ 28 LOUTL 29 PCIE_CLK- 30 LOUTR 31 GND
42 CLK33M 43 SLP_S5# 44 LPC_AD0 45 DDP_HPD 46 LPC_AD1 47 GND 48 LPC_AD2 49 DDP_AUX+ 50 LPC_AD3 51 DDP_AUX- 52 LPC_DRQ#0 53 GND 54 LPC_SERIRQ 55 DDP_D0+ 56 LPC_FRAME# 57 DDP_D0- 58 GND 59 GND 60 USB0_D+ 61 DDP_D1+ 62 USB0_D- 63 DDP_D1- 64 GND 65 GND 66 USB1_D+/USB_SSTX+ 67 DDP_D2+ 68 USB1_D-/USB_SSTX- 69 DDP_D2- 70 GND 71 GND 72 USB2_D+/USB_SSRX+ 73 DDP_D3+ 74 USB2_D-/USB_SSRX- 75 DDP_D3- 76 GND 77 GND 78 USB_OC# 79 +12VSB 80 NC 83
Appendix A Pin Assignments CN29 PCIe Mini Card Holder Part Number 1654002539 Footprint FOX_AS0B226-S68K7F_HOLDER Description MINI PCI Express 52P 6.
CN30 PCIe Mini Card Part Number 1654002538 Footprint FOX_AS0B226-S68K7F Description MINI PCI Express 52P 6.8mm 90D SMD AS0B226-S68N7 Pin Pin Name 1 WAKE# 2 +3.3VSB 3 NC 4 GND 5 NC 6 +1.5V 7 NC 8 NC 9 GND 10 NC 11 REFCLK- 12 NC 13 REFCLK+ 14 NC 15 GND 16 NC 17 NC 18 GND 19 NC 20 NC 21 GND 22 PERST# 23 PERn0 24 +3.
GND 28 +1.5V 29 GND 30 SMB_CLK 31 PETn0 32 SMB_DAT 33 PETp0 34 GND 35 GND 36 USB D- 37 GND 38 USB D+ 39 +3.3VSB 40 GND 41 +3.3VSB 42 NC 43 GND 44 NC 45 NC 46 NC 47 NC 48 +1.5V 49 NC 50 GND 51 NC 52 +3.
CN31 CFast Part Number 1653004402 Footprint CFAST_24P_N7E24 Description CFast 24P 1.27mm 90D(M) SMD N7E24-M516RA-50 Pin Pin Name PC1 CDI PC2 GND PC3 NC PC4 NC PC5 NC PC6 NC PC7 GND PC8 NC PC9 NC PC10 NC PC11 NC PC12 NC PC13 +3.3V PC14 +3.
GND PC17 CDO S1 GND S2 TX+ S3 TX- S4 GND S5 RX- Appendix A Pin Assignments PC16 S6 RX+ S7 GND FAN1 CPU FAN Part Number 1655003010 Footprint W_3V_2.54mm Description Wafer 2.
MIO-5270 User Manual 56
Appendix B B System Assignment
B.1 System I/O Ports Table B.1: System I/O Ports Addr.
Appendix B System Assignment B.3 Interrupt assignments Table B.
MIO-5270 User Manual 60
Appendix C Watchdog Timer Sample Code C
C.1 EC Watchdog Timer sample code EC_Command_Port = 0x29Ah EC_Data_Port = 0x299h Write EC HW ram = 0x89 Watch dog event flag = 0x57 Watchdog reset delay time = 0x5E Reset event = 0x04 Start WDT function = 0x28 ==================================================== .model small .486p .stack 256 .data .code org 100h .STARTup mov dx, EC_Command_Port mov al,89h ; Write EC HW ram. out dx,al mov dx, EC_Command_Port mov al, 5Fh ; Watchdog reset delay time low byte (5Eh is high byte) index.
Appendix D AMD G-Series D
Advantech MIO-5270 is a MIO compact Single Board Computer with AMD G-series APU which supports AMD accelerated processing technology. This technology (known as ATI stream) is a software and hardware combination that enables CPU graphic engine acceleration. This acceleration can be supported with specific 3rd party applications. Target List of Supported 3rd Party Applications: Adobe Flash Player 10.
Appendix D AMD G-Series MIO-5270 User Manual 65
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
