Tablet-PC AMD LX800® M processor-based Point of Care Terminal with 10.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Additional Information and Assistance 1. Visit the Advantech websites at www.advantech.com or www.advantech.com.tw where you can find the latest information about the product. 2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance.
16. If your computer is losing dramatic time or the BIOS configuration reset to default, the battery has no power. Caution 1. Do not replace battery yourself. Please contact a qualified technician or your retail. 2 .The computer is provided with a battery-powered real-time clock circuit. There is a danger of explosion if battery is incorrectly replaced. Replace only with same or equivalent type recommended by the manufacture. Discard used batteries according to the manufacturer’s instructions 17.
Explanation Of Graphical Symbols: This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit. This symbol alerts the user that important literature concerning the operation and maintenance of this unit has been included. Therefore, it should be read carefully in order to avoid any problems.
Chapter 1General Information 1.0 Introduction The Tablet PC is a multimedia AMD® Mobile processor-based computer that is designed to serve as a Point of Care terminal (POC.) It is a PC-based system with 10.4" color TFT LCD display and 18-bit stereo audio controller. Tablet PC is a mobile point of care for system integrators, this simple, complete and highly integrated multimedia system lets you easily build a Point of Care Terminal into your applications.
Environment Adapter Model: MPU100-106 Auto-switching 100-240VAC, 47-63Hz, 1.25-0.5A Supplying 15VDC with a current of 6.
LCD model (MT-100-TE) Toshiba LTD104KA1S Display type TFT color LCD Size (Diagonal) 10.4” Resolution 1024(W) x 768(H) pixels ( XGA) Maximum colors 256K(R,G,B 6 bit color data) Pixel pitch (mm) 0.2055(W) x 0.2055(H) viewing (Upper+Lower) 50 degree angle (Left+Right) 90 degree Luminance (cd/m2) 170 cd/m2 Contrast ratio 250:1 Lamp lifetime 50,000 hours at 6.5mA Table 1.3: Toshiba LCD Panel specification 1.
1.4 MT-CRADLE Specifications MT-CRADLE Description Dimension （W×D×H） 217.4 x 156.8 x 42.4 mm (8.56” x 6.17” x 1.67”) Weight 800g I/O USB USB2.0 x 4 COM RS-232 x 1 LAN Giga Bit Ethernet x1 VGA VGA output port x1 DC-in Yes Cradle Ports Docking Smart Card reader Yes Model: MPU100-106 Auto-switching 100-240VAC, 47-63Hz, 1.25-0.5A Supplying 15VDC with a current of 6.
1.5 Dimensions Dimensions :266.4 x 211.4 x 36 mm ; VESA mount 75 x75mm Figure 1-1: Dimensions of the Tablet PC Dimensions : 217.4 x 156.8 x 42.
Chapter 2 System Setup 2.1 A Quick Tour of the Tablet PC Before you start to set up the Tablet PC, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. When you place the Tablet PC upright on the desktop, its front panel appears as shown in Figure 2-1.
USB Port Figure 2-3: Left side view of the Tablet PC When you turn the Tablet PC around and look at its rear cover. Figure 2-4.
The optional Docking device : MT-CRADLE When you place the CRADLE upright on the desktop, its front panel appears as shown in Figure 2-5. Figure 2-5: Front View of the CRADLE When you turn the CRADLE around and look at its rear cover. Figure 2-6.
2.2 Installation Procedures 2.2.1 Powering the Tablet PC by Battery Power The MT-100 tablet PC is supplied with a powerful rechargeable battery. To install and maintain the battery, or if it needs to be replaced, follow the instructions in this section. Caution! Do not attempt to replace the battery with any others than the models recommended and manufactured specifically for this tablet PC.
5. Push up the battery pack to close connection with system. Figure 2-8: Push up the battery pack to close 5. Fasten the two battery cover screws.
2.2.2 Connecting the adapter with Tablet Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Connect the female end of the AC Adapter cord to the DC Power inlet of the Tablet PC. (See Figure 2-5.) 2. Connect the female end of the power cord to the AC inlet of the AC Adapter 3. Connect the 3-pin male plug of the power cord to an electrical outlet. 4. Open the power switch on AC Adapter.
2.2.3 Connecting the power cord for CRADLE Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1. Connect the female end of the AC Adapter cord to the DC Power inlet of the CRADLE. (See Figure 2-6.) 2. Connect the female end of the power cord to the AC inlet of the AC Adapter 3. Connect the 3-pin male plug of the power cord to an electrical outlet. 4. Open the power switch on AC Adapter.
2.2.4 Connecting the keyboard and mouse Connect the USB port to the USB mouse and keyboard port on the I/O section of the Tablet PC. (See Figure 2-7.
2.2.4 Combining with CRADLE 1. The CRADLE must be fixed on VESA mount(75mmx75mm) first. 2. Connect the female end of the AC Adapter cord to the DC Power inlet of the CRADLE. 3. The Tablet PC must vertical landing to CRADLE (See Figure 2-8.) 4. The button on up of CRADLE down and switch off then Tablet PC can vertical takeoff CRADLE .
2.2.5 Separating with CRADLE 1. The Switch must on “Right side” and Button push down (see table 2-1 & Figure 2-9.) 2. The Tablet PC can vertical takeoff CRADLE . Switch Button Left side Right side High Always lock lock Low Always un-lock un-lock Table 2-1: The selection of Lock of CRADLE Remark: If the switch on the left side then Button mode can’t be changed so Always Lock or Always un-lock. You must change the switch to right side then can change the Button mode.
2.3 LED Signals The MT-100 is equipment with a set of Light Emitting Diodes(LEDs) located along the right top of the front Bezel. Battery Status LED Power ON/OFF LED 2.3.1 Power ON/OFF LED z z z Dark : No DC-in from AC adapter Static Green : DC-in from AC adapter Blinking Green: System is in standby mode with AC Adapter DC-in. 2.3.
2.3.3 CRADLE Status LED Docking Status LED Power ON/OFF LED 2.3.4 Power ON/OFF LED z z Dark : No Power input Static Green : the CRADLE is powered by adapter 2.3.5 Docking Status LED z z Dark : No Power input or Docking status is no or NO good. (if the system is powered by Adapter) Static Green : Docking status is good with Tablet PC (If the system is powered by adapter) 2.3.6 Caution message on CRADLE Caution! Do not touch the metal pin of Docking by finger, conductivity material , and liquid.
2.4 Buttons The hotkey button on right down side of front bezel. UP Down Keyboard on Screen Display rotation Touch ON/OFF Button 2.4.1 UP button The “UP” button function is same as Keyboard “UP” key. 2.4.2 DOWN button The “DOWN” button function is same as Keyboard “DOWN” key. 2.4.3 Keyboard on Screen button The keyboard button function can enable On-Screen Keyboard utility. 2.4.4 Display rotation button The rotation button function is the hotkey for rotating the display on screen. 2.4.
2.5 Running the BIOS Setup Program Your Tablet PC is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. The setup program is stored in read-only memory.
2.8 Installing the Drivers After installing your system software, you will be able to set up the Ethernet, SVGA, audio and touch screen functions. All the drivers except the CD-ROM drive driver are stored in a CDROM disc entitled "Drivers and Utilities which can be found in your accessory box. The standard procedures for installing the Ethernet, SVGA, audio and touch screen drivers are described in Chapters 3, 4, 5, 6 and 7 respectively. The utility directory includes multimedia programs.
Chapter 3 Graphic chipset Setup 3.1 Introduction The MT-100 has an onboard VGA interface. The specifications and features are described as follows: 3.1.1 Chipset The MT-100 uses Mobile AMD LX800 /CS5336 chipset for its graphic controller. It supports SDVO device, and CRT monitors. The Mobile AMD LX800 /CS5336 chipset is a component of the AMD® mobile technology. 3.1.2 Display memory Max memory allocation support based on total system memory 1-MB or 8 MB of pre-allocated memory supported. 3.1.
3.2 Installation of Chipset Driver Complete the following steps to install the chipset driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your MT-100. Step 1-1 Click the 'Start' button in the task bar, click 'Control Panel', click 'System' then show a dialogue windows of System Properties. Then Click the 'Hardware', Click 'Device Manager'. The Install dialog will appear.
Step 1-3 Click the Circle of ‘Yes, this time only ‘ then Click ‘Next’ step. Please Click the Circle of ‘Install from a list or specific location (Advanced). Step 1-4 Click the ‘Include this location in the search’. Then Browse the direction of D:\CHIPSET\AES’ then Click ‘Next’.
Step 1-5 The system will auto install the Chipset drive as below window. Step 1-6 Please direct to ‘D:\CHIPSET\AES’ then Click ‘OK’ if need more information for installation.
Step 1-7 When appear the ‘Completing the Hardware update Wizard’ dialog then can Click the ’Finish’ button to complete it. Important The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which appear on your screen. Note1 The CD-ROM drive is designated as “D:” throughout this chapter. Note2 means pressing the “Enter” key on the keyboard.
3.3 Installation of Graphic Driver Complete the following steps to install the SVGA driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your MT-100. Step 1-1 Click the 'Start' button in the task bar, click 'Control Panel', click 'System' then show a dialogue windows of System Properties. Then Click the 'Hardware', Click 'Device Manager' then appear the ‘Device manager’ dialog.
Step 1-3 Click the Circle of ‘Yes, this time only ‘ then Click ‘Next’ step. Please Click the Circle of ‘Install from a list or specific location (Advanced). Step 1-4 Click the ‘Include this location in the search’. Then Browse the direction of ‘D:\VGA\GeodeLX_XP_XPe_Graphics _v3.03.06’ then Click ‘Next’.
Step 1-5 The system will auto install the Chipset drive as below window. Step 1-6 Please select ‘Continue Anyway’.
Step 1-7 System automatic to install the VGA drive as below window. Step 1-8 Please direct to ‘D:\VGA\GeodeLX_XP_XPe_Graphics _v3.03.06’ then Click ‘OK’ if need more information for installation.
Step 1-9 When appear the ‘Completing the Hardware update Wizard’ dialog then can Click the ’Finish’ button to complete it. Important The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which appear on your screen. Note1 The CD-ROM drive is designated as “D” throughout this chapter. Note2 means pressing the “Enter” key on the keyboard.
3.4 Installation of Audio Driver Complete the following steps to install the Audio driver. Follow the procedures in the flow chart that apply to the operating system that you are using within your MT-100. Important The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which appear on your screen. Note1 The CD-ROM drive is designated as “D” throughout this chapter.
Step 1-2 Click the ‘Sound, Video and Game controllers’ then double Click the ‘Multimedia Audio Controller’. Appear a New dialog then Click the ‘Driver’, Select ‘Update Driver’ will show as below dialog. Step 1-3 Click the Circle of ‘Yes, this time only ‘ then Click ‘Next’ step. Please Click the Circle of ‘Install from a list or specific location (Advanced).
Step 1-4 Click the ‘Include this location in the search’. Then Browse the direction of ‘D:\AUDIO\Audio’ then Click ‘Next’. Step 1-5 System will automatic to install the Chipset drive as below window.
Step 1-6 Please select ‘Continue Anyway’. Step 1-7 Please direct to ‘D:\AUDIO\Audio’ then Click ‘OK’ if need more information for installation.
Step 1-8 System will continuing install the Chipset drive as below window. Step 1-9 When appear the ‘Completing the Hardware update Wizard’ dialog then can Click the ’Finish’ button to complete it.
3.4.1 Further information For further information about the CHIPSET, VGA , AUDIO installation in your MT-100, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. AMD website: www.AMD.com Advantech websites: www.advantech.
Chapter 4 Touch screen Interface 4.1 Introduction 4.1.1 General Information The MT-100's optional touch screen incorporates advanced second-generation 5-wire resistive technology. They allow 75% light transmission respectively. The resistive and capacitive models have an antiglare surface. All models provide greatly enhanced visual resolution. They also have new improved scratch-resistant features. The touch screen is manufactured from UL-recognized components.
4.2.1 Installation for Windows 2000/XP 4.3 Further information For further information about the Touchscreen installation in your MT-100, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. ELO website: http://www.elotouch.com/ EETI website: http://www.eeti.com.tw/ Advantech websites: www.advantech.
Chapter 5 Hotkey function Application 5.1 Introduction 5.1.1 General Information The MT-100's features a build in Wireless Ethernet card by MiniPCI interface. Free cable when you surfing web screen, Display rotation and T/S on/off button. There Hotkey can customize if customer have request for it. 5.1.2 Install Hotkey AP Important The following windows illustrations are examples only. You must follow the flow chart instructions and pay attention to the instructions which appear on your screen.
Step 1-2 Wait for the AP automatic install. Step 1-3 Press the “Next” when show the window.
Step 1-4 Please select the “ I accept the term of the license agreement” then press ”Next”. Step 1-5 AP will keep going to implement it.
Step 1-6 Press the “Finish” button when show the Complete window.
Chapter 6 WLAN driver installation 6.1 Introduction 6.1.1 General Information Step 1-1 Click the ‘Include this location in the search’. Then Browse the direction of ‘D:\WLAN\ 080229_RT61_D_1.2.3.0_VA_2.1.0.0_RaUI_2.0.7.0_VA_2.0.9.0_for 2K&XPx86 VAx86’ then double Click it.
Step 1-2 The WLAN drivers will auto download file then show the License window. Please select the “ I accept the term of the license agreement” then press ”Next”. Step 1-3 Select the “Ralink Corporation Tool” then Press ‘Next’.
Step 1-4 Select the ‘Optimize WiFi mode’ then Press ‘Next’.
Step 1-5 Auto install driver Step 1-6 Driver implement complete, Please press the ‘Finish’ button.
Step 1-7 Ralink WLAN utility user interface . 6.1 Further information For further information about the WLAN card installation in your MT-100, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. RaLink website: http://www.Ralink.com.tw/ Advantech websites: www.advantech.
Chapter 7 MT-CRADLE drivers installation 7.1 Introduction 7.1.1 General Information MT-CRADLE is MT-100 tablet PC series option Docking station. It is include multi I/O port for more application. These I/O port include USB x 4 ports, RS-232 Port x1, Gigabit LAN port x1, VGA port and Smart Card Reader. We must install drivers for these add on I/O ports then by be 1. The CRADLE must be fixed on VESA mount(75mmx75mm) first. 2. Connect the female end of the AC Adapter cord to the DC Power inlet of the CRADLE.
7.2. USB to LAN driver installation Step 1-1 When you setup the cradle and plug the power in with adapter. The MT-100 tablet PC connect with CRADLE. The SYSTEM will auto detect “Found New Hardware” . The show the “Files needed” windows. Please press the “Browse” .
Step 1-2 Then Browse the direction of ‘D:\USB-LAN\ F:\AX88772_772A_WinXP2K_32bit_v3.4.3.18_WHQL’ will show the AX88772.sys file. Select it and press the “Open” Button. Step 1-3 Please press the “OK” Button then auto implement the drivers.
Step 1-4 You can double check after install driver on Device manager. As below red line the driver is available on system.
7.2. USB to RS-232 driver installation Step 1-1 Browse the direction of ‘D:\USB to RS-232\wd_pl2303h-hx-x_v20019v2021’ the can find “PL-2303 Driver Installer” file. Then double clock it. Step 1-2 The driver will auto install it. Please select “Yes, I want to reboot computer now” and press the “Finish’ button. System will re-boot. The driver is available.
7.3. Smart Card reader driver installation 7.3.
Step 1-1 Click the ‘Include this location in the search’. Then Browse the direction of ‘D:\Smart Card Reader\ACR’ then double Click ‘Setup’. Step 1-2 Wait for the AP automatic install.
Step 1-3 Please select the “Yes” button to continue installation. Step 1-4 Please express the “Finish” button when show the screen. Complete driver installation.
7.4.3 Further informatio For further information about the Smart card reader installation in your MT-100, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. The model is ACR38. ACS website: http://www.ACS.com.hk Advantech websites: www.advantech.
