PCA-6179 Full-size socket 370 Intel® Pentium® III processorbased PCI/ISA-bus CPU card
Copyright notice This document is copyrighted, 2000, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
A Message to the Customer Advantech customer services Each and every Advantech product is built to the most exacting specifications to ensure reliable performance in the harsh and demanding conditions typical of industrial environments. Whether your new Advantech equipment is destined for the laboratory or the factory floor, you can be assured that your product will provide the reliability and ease of operation for which the name Advantech has come to be known. Your satisfaction is our primary concern.
PCA-6179 Series comparison table Model PCA-6179L PCA-6179V PCA-6179VE PCA-6179VS PCA-6179F CPU: Intel®Pentium® III Socket 370 ✓ ✓ ✓ ✓ ✓ System chipset: VIA Apollo Pro 133 A ✓ ✓ ✓ ✓ ✓ BIOS: Award P&P Flash BIOS ✓ ✓ ✓ ✓ ✓ L2 Cache: 256 KB (on CPU) ✓ ✓ ✓ ✓ ✓ Max. System RAM: 1.
Product warranty Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as a consequence of such events.
Initial Inspection Before you begin installing your card, please make sure that the following materials have been shipped: • 1 PCA-6179 socket 370 Pentium III® processor-based single board computer • 1 Pentium III® processor, (optional) 1 cooling fan, P/N: 1759205400 • 1 PCA-6179 startup Manual • 1 CD driver utility and manual (in PDF format) • 4 SCSI driver disks (optional) • 1 FDD cable, P/N: 1701340703 • 2 UDMA 66 HDD cables, P/N: 1701400452 • 1 printer (parallel port) cable & COM port cable kit, P/N: 17
Contents Chapter 1 Hardware Configuration .............................. 1 1.1 1.2 1.3 Introduction ........................................................................2 Features ...............................................................................3 Specifications ......................................................................5 1.3.1 System .........................................................................5 1.3.2 Memory ...........................................................
2.1 Primary (CN1) and Secondary (CN2) IDE Connectors24 2.2 Floppy Drive Connector (CN3) .......................................25 2.3 Parallel Port (CN4) ..........................................................25 2.4 SCSI Connector (CN5) ....................................................26 2.5 USB Port (CN6) ................................................................27 2.6 VGA Connector (CN7) ....................................................27 2.7 10/100Base-T Ethernet Connector (CN8) ..........
3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 3.4.6 Typematic Rate Setting .............................................40 3.4.7 Typematic Rate (Chars/Sec) .....................................41 3.4.8 Typematic Delay (msec) ........................................... 41 3.4.9 Security Option .........................................................41 3.4.10 OS Select for DRAM > 64MB................................ 41 3.4.11 Video BIOS Shadow ...............................................41 3.4.
4.1 4.2 4.3 Before You Begin .............................................................52 Features .............................................................................52 Installation ........................................................................53 Chapter 5 LAN Configuration ..................................... 55 5.1 Introduction ......................................................................56 5.2 Features ....................................................................
B.10 B.11 B.12 B.13 B.14 B.15 B.16 B.17 B.18 B.19 B.20 B.21 B.22 External Keyboard Connector (CN12) ........................110 IR Connector (CN13) .....................................................111 CPU Fan Power Connector (CN14) .............................111 Power LED and Keylock Connector (CN16) ...............112 External Speaker Connector (CN17) ...........................112 Reset Connector (CN18) ................................................113 HDD LED Connector (CN19) ...................
Tables Table 1-1: Jumpers .......................................................................................................... 9 Table 1-2: Connectors .................................................................................................... 10 Table 1-3: CPU clock ratio setting (SW1) ...................................................................... 14 Table 1-6: Watchdog timer output (J2) ..........................................................................
Figures Figure 1-1: Board layout: main features ....................................................................... 8 Figure 1-2: Board layout: jumper and connecter locations ............................................
CHAPTER 1 Hardware Configuration This chapter gives background information on the PCA-6179. It then shows you how to configure the card to match your application and prepare it for installation into your PC.
1.1 Introduction The PCA-6179 Series all-in-one industrial grade CPU card uses Intel's highly acclaimed Pentium® III processor, together with the VIA Apollo Pro133A chipset. The card works with standard ISA or PCI/ISA-bus passive backplanes. The CPU provides 256 KB on-CPU L2 cache, eliminating the need for external SRAM chips. It has two PCI EIDE interfaces (for up to four devices) and a floppy disk drive interface (for up to two devices).
1.2 Features 1. Fan status monitoring and alarm: To prevent system overheating and damage, the CPU fan can be monitored for speed and failure. The fan is set for its normal RPM range and alarm thresholds. 2. Temperature monitoring and alert: To prevent system overheating and damage, the CPU card supports processor thermal sensing and auto-protection. 3. Voltage monitoring and alert: System voltage levels are monitored to ensure stable current flows to critical components.
8. CMOS RAM backup: When BIOS CMOS setup has been completed, data in the CMOS RAM is automatically backed up to the Flash ROM. This is particularly useful in industrial environments which may cause soft errors. Upon such an error occurring, BIOS will check the data, and automatically restore the original data for booting. 9.
1.3 Specifications 1.3.1 System • CPU: Intel Pentium® III processor, up to 933+ MHz, FSB 100/133 MHz • BIOS: Award Flash BIOS, 2 Mbit • System Chipset: VIA Apollo Pro133A • Green function: Supports power management operation via BIOS. Activated by keyboard or mouse activity • PCI enhanced IDE hard disk drive interface: Supports up to four IDE (AT-bus) large hard disk drives or other enhanced IDE devices. Supports PIO mode 4 (16.
1.3.3 Input/Output • Bus interface: PCI/ISA bus, PICMG compliant • Enhanced parallel port: Configurable to LPT1, LPT2, LPT3, or disabled. Standard DB-25 female connector provided. Supports EPP/ECP • Serial ports: Two RS-232 ports with 16C550 UARTs (or compatible) with 16-byte FIFO buffer. Supports speeds up to 115.2 Kbps.
1.3.8 Industrial features • Watchdog timer: Can generate a system reset or IRQ11. The watchdog timer is programmable, with each unit equal to one second (63 levels). The program uses I/O port hex 443h to control the watchdog timer 1.3.9 Mechanical and environmental specifications • Operating temperature: 0 ~ 60° C (32 ~ 140° F) • Storage temperature: -40 ~ 60° C (-40 ~ 140° F) • Humidity: 20 ~ 95% non-condensing • Power supply voltage: +5 V, ±12 V • Power consumption: +5 V @ 4.
8 PCA-6179 User's Manual SCSI connector EIDE connectors Three DIMM sockets up to 1.5 GB Socket370 VIA Apollo Pro Pentium® III CPU 133A chipset up to 933+ MHz DOC 2000 Parallel port FDD connector mouse and keyboard connector VGA connector LAN connector COM 2 COM 1 USB port 1.
1.5 Jumpers and Connectors Connectors on the PCA-6179 board link it to external devices such as hard disk drives and a keyboard. In addition, the board has a number of jumpers used to configure your system for your application. The tables below list the function of each of the board jumpers and connectors. Later sections in this chapter give instructions on setting jumpers. Chapter 2 gives instructions for connecting external devices to your card.
Table 1-2: Connectors 10 Label Function CN1 Primary IDE connector CN2 Secondary IDE connector CN3 Floppy drive connector CN4 Parallel port CN5 SCSI connector CN6 USB port CN7 VGA connector CN8 10/100Base-T Ethernet connector CN9 Serial port: COM1 CN10 Serial port: COM2 CN11 PS/2 keyboard and mouse connector CN12 External keyboard connector CN13 Infrared (IR) connector CN14 CPU fan connector CN16 Keyboard lock and power LED CN17 External speaker CN18 Reset connector CN19
1.
1.7 Safety Precautions Warning! Always completely disconnect the power cord from your chassis whenever you work with the hardware. Do not make connections while the power is on. Sensitive electronic components can be damaged by sudden power surges. Only experienced electronics personnel should open the PC chassis. Caution! 12 Always ground yourself to remove any static charge before touching the CPU card. Modern electronic devices are very sensitive to static electric charges.
1.8 Jumper Settings This section provides instructions on how to configure your card by setting jumpers. It also includes the card's default settings and your options for each jumper. 1.8.1 How to set jumpers You configure your card to match the needs of your application by setting jumpers. A jumper is a metal bridge that closes an electrical circuit. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them.
1.8.4 CMOS clear (J1) The PCA-6179 CPU card contains a jumper that can erase CMOS data and reset the system BIOS information. Normally this jumper should be set with pins 1-2 closed. If you want to reset the CMOS data, set J1 to 2-3 closed for just a few seconds, and then move the jumper back to 1-2 closed. This procedure will reset the CMOS to its default setting.
1.8.5 DiskOnChip® 2000 Flash disk address select (SW3) The PCA-6179 includes a 32-pin socket for M-Systems' DiskOnChip® 2000 Flash disk module. This revolutionary solid state disk enables critical system information to be stored within an on-board Flash disk for virtually instantaneous data access. You must specify the memory address you want to use for your DiskOnChip 2000 Flash disk module by setting jumper (SW3).
Table 1-7: DiskOnChip® 2000 Flash disk memory address jumper settings (J3) Segment SW3-1 SW3-2 SW3-3 SW3-4 CC00h ON ON OFF OFF D000h ON OFF ON OFF D400h ON OFF OFF OFF D800h OFF ON ON OFF DC00h OFF ON OFF OFF E000h OFF OFF ON OFF Disable OFF OFF OFF OFF Chapter 1 Hardware Configuration 17
1.9 System Memory The top-left edge of the PCA-6179 contains three sockets for 168-pin dual inline memory modules (DIMMs). All three sockets use 3.3 V unbuffered synchronous DRAMs (SDRAM). DIMMs are available in capacities of 16, 32, 64, 128, 256 or 512 MB. The sockets can be filled in any combination with DIMMs of any size, giving your PCA-6179 single board computer between 16 MB and 1.5 GB of memory.
1.9.2 Supplementary information about DIMMs Your PCA-6179 can accept SDRAM memory chips (with or without parity). Also note: • If the PCA-6179 operates at 133 MHz, only use PC/133-compliant DIMMs. Most systems will not even boot if non-compliant modules are used. This is due to strict timing issues involved at this speed. • SDRAM chips are usually thinner and have higher pin density than EDO chips. • Chips with 9 chips/side support ECC; chips with 8 chips/side do not support ECC.
1.10 Memory Installation Procedures To install DIMMs, first make sure the two handles of the DIMM socket are in the "open" position. i.e. The handles lean outward. Slowly slide the DIMM module along the plastic guides on both ends of the socket. Then press the DIMM module right down into the socket, until you hear a click. This is when the two handles have automatically locked the memory module into the correct position of the DIMM socket.
1.12 CPU Installation The PCA-6179 provides a socket 370 for an Intel® Coppermine processor. The CPU on the board must have a fan or heat sink attached, to prevent overheating. Warning: Without a fan or heat sink, the CPU will overheat and cause damage to both the CPU and the motherboard. To install a CPU, first turn off your system and remove its cover. Locate the processor socket 370. 1. Make sure the socket 370 lever is in the upright position.
22 PCA-6179 User's Manual
CHAPTER 2 Connecting Peripherals This chapter tells how to connect peripherals, switches and indicators to the PCA-6179 board. You can access most of the connectors from the top of the board while it is installed in the chassis. If you have a number of cards installed, or your chassis is very tight, you may need to partially remove the card to make all the connections.
2.1 Primary (CN1) and Secondary (CN2) IDE Connectors CN1 CN2 You can attach up to four IDE (Integrated Device Electronics) drives to the PCA-6179’s internal controller. The primary (CN1) and secondary (CN2) connectors can each accommodate two drives. Wire number 1 on the cable is red or blue and the other wires are gray. Connect one end to connector CN1 or CN2 on the CPU card. Make sure that the red/blue wire corresponds to pin 1 on the connector (in the upper right hand corner).
2.2 Floppy Drive Connector (CN3) CN3 You can attach up to two floppy disk drives to the PCA-6179's onboard controller. You can use any combination of 5.25" (360 KB / 1.2 MB) and/or 3.5" (720 KB / 1.44/2.88 MB) drives. The card comes with a 34-pin daisy-chain drive connector cable. On one end of the cable is a 34-pin flat-cable connector. On the other end are two sets of floppy disk drive connectors. Each set consists of a 34-pin flat-cable connector (usually used for 3.
To install the bracket, find an empty slot in your chassis. Unscrew the plate that covers the end of the slot. Screw in the bracket in place of the plate. Next, attach the flat-cable connector to CN4 on the CPU card. Wire 1 of the cable is red or blue, and the other wires are gray. Make sure that wire 1 corresponds to pin 1 of CN4. Pin 1 is on the upper right side of CN4. 2.4 SCSI Connector (CN5) CN5 The PCA-6179 has a 68-pin, dual in-line connector for Ultra2 Wide SCSI devices.
2.5 USB Port (CN6) Pin 1 CN6 The PCA-6179 provides one USB (Universal Serial Bus) interface, which gives complete Plug & Play and hot attach/detach for up to 127 external devices.The USB interface complies with USB Specification Rev. 1.0 and is fuse-protected. The USB interface is accessed through a 10-pin flat-cable connector, CN6. The adapter cable has a 10-pin connector on one end and a USB connector on the bracket. The USB interface can be disabled in the system BIOS setup. 2.
2.7 10/100Base-T Ethernet Connector (CN8) CN8 The PCA-6179 is equipped with a high-performance 32-bit PCI-bus Ethernet interface, which is fully compliant with IEEE 802.3/u 10/100 Mbps CSMA/CD standards. It is supported by all major network operating systems and is 100% Novell NE-2000 compatible. An onboard RJ-45 jack provides convenient 10/100Base-T RJ-45 operation. 2.8 Serial Ports (CN9: COM1; CN10: COM2) CN10 CN9 The PCA-6179 offers two serial ports, CN9 as COM1 and CN10 as COM2.
The IRQ and address ranges for both ports are fixed. However, if you want to disable the port or change these parameters later, you can do this in the system BIOS setup. Different devices implement the RS-232 standard in different ways. If you are having problems with a serial device, be sure to check the pin assignments for the connector. 2.9 PS/2 Keyboard and Mouse Connector (CN11) CN11 The PCA-6179 board provides a keyboard connector.
2.11 Infrared (IR) Connector (CN13) CN13 This connector supports the optional wireless infrared transmitting and receiving module. This module mounts on the system case. You must configure the setting through the BIOS setup (see Chapter 3). 2.12 CPU Fan Connector (CN14) CN14 PIN 1 This connector supports cooling fans of 500 mA (6 W) or less.
2.13 Front Panel Connectors (CN16, CN17, CN18, CN19, CN21 and CN22) There are several external switches to monitor and control the PCA-6179. CN18 CN22 CN16 CN21 J1 CN19 CN17 2.13.1 Keyboard lock and power LED (CN16) CN16 is a 5-pin connector for the keyboard lock and power on LED. Refer to Appendix B for detailed information on the pin assignments.
2.13.4 HDD LED (CN19) You can connect an LED to connector CN19 to indicate when the HDD is active. 2.13.5 ATX soft power switch (CN21) If your computer case is equipped with an ATX power supply, you should connect the power on/off button on your computer case to CN21. This connection enables you to turn your computer on and off. 2.14 ATX Power Control Connectors (CN20 and CN21) CN20 PIN 1 Note: Refer to the diagram on the previous page for the location of CN21. 2.14.
Warnings: 1. Make sure that you unplug your power supply when adding or removing expansion cards or other system components. Failure to do so may cause severe damage to both your CPU card and expansion cards. 2. ATX power supplies may power on if certain motherboard components or connections are touched by metallic objects. Important: Make sure that the ATX power supply can take at least a 720 mA load on the 5 V standby lead (5VSB).
34 PCA-6179 User's Manual
CHAPTER 3 Award BIOS Setup This chapter describes how to set the card’s BIOS configuration data.
3.1 Introduction Award’s BIOS ROM has a built-in setup program that allows users to modify the basic system configuration. This type of information is stored in battery-backed RAM so that it retains the setup information when the power is turned off. 3.2 Entering Setup Turn on the computer and check for the “patch code”. If there is a number assigned to the patch code, it means that the BIOS supports your CPU.
3.3 Standard CMOS Features Choose the “STANDARD CMOS FEATURES” option from the “INITIAL SETUP SCREEN” menu, and the screen below will be displayed. This standard setup menu allows users to configure system components such as date, time, hard disk drive, floppy drive, display, and memory.
3.4 Advanced BIOS Features The “ADVANCED BIOS FEATURES” screen appears when choosing the “ADVANCED BIOS FEATURES” item from the “CMOS SETUP UTILITY” menu. It allows the user to configure the CPU Card according to his particular requirements. Below are some major items that are provided in the ADVANCED BIOS FEATURES screen. A quick booting function is provided for your convenience. Simply enable the Quick Booting item to save yourself valuable time.
Realtek Bootstrap selection menu 1.- Disable network boot 2.- Network boot using interrupt 18h 3.- Network boot using interrupt 19h 4.- Network boot using PnP/BEV (BBS) 5.- Network boot from RPL (Int18h/19h) Press 1, 2, 3, 4, or 5: --> The ability to enable the RTL8139(X) BootROM to boot from network depends on underly BIOS support. You should select 1.- disable network boot If you like to disable RTL8139(X) PXE/RPL bootROM. The Rtl8139(X) will operate normally, but will not attempt to remote boot. 2.
anything attempts to access the boot sector or hard disk partition. 3.4.2 Quick Power On Self Test This option speeds up the Power-On Self Test (POST) conducted as soon as the computer is turned on. When enabled, BIOS shortens or skips some of the items during the test. When disabled, the computer conducts normal POST procedures. 3.4.3 Boot Up Floppy Seek During Power-On Self Test (POST), BIOS will determine if the floppy disk drive installed is 40 or 80 tracks.
The typematic rate determines the characters per second accepted by the computer. Typematic Rate Setting enables or disables the typematic rate. 3.4.7 Typematic Rate (Chars/Sec) BIOS accepts the following input values (characters/second) for typematic rate: 6, 8, 10, 12, 15, 20, 24, 30. 3.4.8 Typematic Delay (msec) Typematic delay is the time interval between the appearance of two consecutive characters, when holding down a key. The input values for this category are: 250, 500, 750, 1000 (msec). 3.4.
Shadow increases the video speed. 3.4.12 C8000-CBFFF Shadow / DC000-DFFFF Shadow These determine whether optional ROM will be copied to RAM in blocks of 16 KB. Enabled Optional shadow is enabled. Disabled Optional shadow is disabled. 3.5 Advanced Chipset Features By choosing the “ADVANCED CHIPSET FEATURES” option from the INITIAL SETUP SCREEN menu, the screen below will be displayed. This sample screen contains the manufacturer’s default values for the CPU Card.
3.5.1 Memory Hole At 15 M ~ 16 M Enabling this feature reserves 15 MB to 16 MB memory address space for ISA expansion cards that specifically require this setting. This makes memory from 15 MB and up unavailable to the system. Expansion cards can only access memory up to 16 MB. The default setting is “Disabled.” 3.5.2 AGP Aperture Size (MB) Memory-mapped, graphics data structures can reside in a graphics aperture. The default setting is 64. 3.
enabled. Leave IDE HDD Block Mode on the default setting. 3.6.2 IDE Primary Master/Slave PIO/UDMA Mode, IDE Secondary Master/Slave PIO/UDMA Mode (Auto) Each channel (Primary and Secondary) has both a master and a slave, making four IDE devices possible. Because each IDE device may have a different Mode timing (0, 1, 2, 3, 4), it is necessary for these to be independent. The default setting “Auto” will allow autodetection to ensure optimal performance. 3.6.
direction only. “EPP” allows bidirectional parallel port operation at maximum speed. “ECP” allows the parallel port to operate in bidirectional mode and at a speed faster than the maximum data transfer rate. “ECP + EPP” allows normal speed operation in a two-way mode. 3.6.8 ECP Mode Use DMA This selection is available only if you select “ECP” or “ECP + EPP” in the Parallel Port Mode field. In ECP Mode Use DMA, you can select DMA channel 1, DMA channel 3, or Disable. Leave this field on the default setting.
3.7.1 Power Management This option allows you to determine if the values in power management are disabled, user-defined, or predefined. 3.7.2 HDD Power Down You can choose to turn the HDD off after one of the time intervals listed, or when the system is in “suspend” mode. If the HDD is in a power saving mode, any access to it will wake it up. 3.7.3 Soft-Off by PWR-BTTN If you choose “Instant-Off”, then pushing the ATX soft power switch button once will switch the system to “system off” power mode.
3.7.4 Wakeup Event 3.7.
3.8 PnP/PCI Configurations 3.9 PC Health Status If you enable the OBS function, you can view the temperature, fan speed and voltage of your PC system.
3.10 Frequency Control 3.11 Load Setup Defaults “LOAD SETUP DEFAULTS” loads the values required by the system for maximum performance. 3.12 Set Password To change the password: 1. Choose the “SET PASSWORD” option from the Setup main menu and press . The screen will display the following message: Enter Password: Press .
2. If the CMOS is good or if this option has been used to change the default password, the user is asked for the password stored in the CMOS. The screen will display the following message: Confirm Password: Enter the current password and press . 3. After pressing (ROM password) or the current password (user-defined), you can change the password stored in the CMOS. The password must be no longer than eight (8) characters.
CHAPTER 4 AGP SVGA Setup The PCA-6179 features an onboard PCI AGP/VGA interface. This chapter provides instructions for installing and operating the software drivers on the display driver CD included in your package.
4.1 Before You Begin To facilitate the installation of the enhanced display device drivers and utility software, you should read the instructions in this chapter carefully before you attempt installation. The enhanced display drivers for the PCA-6179 board are located on the software installation CD. You must install the drivers and utility software by using the supplied SETUP program for DOS drivers. Note: The files on the software installation CD are compressed.
• User-friendly installation for Windows 95 and Windows NT • AGP 1.0 interface • Supports SDRAM and SGRAM at up to 125 MHz memory clock providing bandwidth up to 2 GB/S across a 128-bit interface. • Integrates superior video features. These include filtered sealing of 720 pixel DVD content, and MPEG-2 motion compensation for software DVD 4.3 Installation First, insert CD drive. Then follow the Icons for your PCA Series model number. Click on the right driver for the auto-installation.
54 PCA-6179 User's Manual
CHAPTER 5 LAN Configuration The PCA-6179 features an onboard LAN interface. This chapter gives detailed information on Ethernet configuration. It shows you how to configure the card to match your application requirements.
5.1 Introduction The PCA-6179 features an optional 32-bit 10/100 Mbps Ethernet network interface. This interface supports bus mastering architecture and auto-negotiation features. Therefore standard twisted-pair cabling with RJ-45 connectors for both 10 Mbps and 100 Mbps connections can be used. Extensive driver support for commonly-used network systems is also provided. 5.
5.3 Driver Installation The PCA-6179's onboard Ethernet interface supports all major network operating systems. The BIOS automatically detects the LAN while booting, and assigns an IRQ level and I/O address. No jumpers or switches are required for user configuration. The drivers and installation instructions are located in the following directories of the utility CD: • Dos: Drivers for DOS platforms • Info: Installation instructions • Nwserver: Drivers for Novell NetWare • Wfw: Drivers for Windows 3.
5.4 Windows 9X Drivers Setup Procedure Note 1: If you are using Windows 98SE, your system will find the LAN device "PCI Ethernet Controller". You must first remove this device from your system, and then restart your computer. Then you will be ready to install the correct driver by following the procedure below. Note 2: The CD-ROM drive is designated as "E" throughout this section. 1. In the "Windows" screen, click on "Start" and select "Settings". Then click on the "Control Panel" icon to select "System".
2. In the "System Properties" window, select the "Device Manager" tab. Select "View devices by type", and navigate to: Computer\Other devices\PCI Ethernet Controller. Highlight "PCI Ethernet Controller" and click on "Properties".
3. In the "PCI Ethernet Controller Properties" window, select the "Driver" tab. Then click on "Update Driver...". 4. In the "Update Device Driver Wizard" window, click on "Next".
5. Click "Next". 6. In the following "Update Device Driver Wizard" window, select "Specify a location:". Type in: "E:\PCA6178\LAN". Then click on "Next".
7. In the following "Update Device Driver Wizard" window, select "The updated driver ...". Then click on "Next". 8. In the following "Update Device Driver Wizard" window, click on "Next".
9. In the "Copying Files..." window, the correct file path should be: E:\PCA6179\LAN\WIN98. When you have the correct location, click on "OK". 10. When the "Insert Disk" window appears, insert the utility CD into the CD-ROM drive. Then click on "OK".
11. When the "Update Device Driver Wizard" window shows, click on finish. 12. In the "System Settings change" window, select click on "Yes".
5.5 Windows NT Drivers Setup Procedure Note: The CD-ROM drive is designated as "E" throughout this section. 1. In the "Windows NT" screen, click on "Start" and select "Settings". Then click on the "Control Panel" icon to select "Network". 2. In the "Network" window, select the "Adapters" tab. Then click on "Add...".
3. In the "Select Network Adapter" window, click on "Have Disk...". 4. When the "Insert Disk" window appears, insert the utility CD into the CD-ROM drive. The correct file path is; E:\PCA6179\LAN\WINNT4. When you have the correct file path, click on "OK".
5. In the "Select OEM Option" window, click on "OK". 6. In the "Duplex mode", click "OK".
7. In the "Network" window, select the "Adapters" tab. Under "Network Adapters:", highlight "Realtek RTL8139CA/B/C(8130). 8. In the "Microsoft TCP/IP Properties" window, select the "IP Address" tab. Then select "Specify an IP address". Type in the IP Address and Subnet Mask details. Then click on "OK".
9. In the "Network Settings Change" window, click on "Yes".
5.6 Windows 2000 Drivers Setup Procedure Note: The CD-ROM drive is designed as "E" throughout this section. 1. In the "Windows 2000" screen, click on " Start" and select " settings". Then click on the " Control Panel" icon to select "system".
2. In the " System Properties" window, select the " Device Manager".
3. In "Device Manager" screen, follow the screen instructions, to click on "Properties". 4. In the following screen, to click on "Update Driver".
5. Click on "Next". 6. Following the highlighted item, and click on "Next".
7. Click on "Have Disk". 8. Key in "E:\Pca6179\Lan\WIN2000", then click on "OK".
9. To highlight the following item, and click "Next". 10. Click "Next".
11. Click "Finish" to complete teh installation.
CHAPTER 6 SCSI Setup and Configurations The PCA-6179 features an onboard SCSI interface. This chapter provides basic SCSI concepts and instructions for installing the software drivers with the SCSI driver disks/CD included in your package.
6.1 Introduction The PCA-6179 is equipped with a Symbios SYM53C895 single-chip PCI-to-SCSI host adapter which provides a powerful Ultra2 multitasking interface between your computer’s PCI bus and SCSI devices (disk drives, CD-ROM drives, scanners, tape backups, removable media drives, etc.). Up to a total of 15 SCSI devices can be connected to the SCSI connector through the Symbios SYM53C895. The SYMBIOS 53C895 is a 16-bit, LVD/SE (Low Voltage Differential/Single-Ended) SCSI solution for your computer.
6.3 Basic Rules for SCSI Host Adapter and Device Installation You must terminate both ends of the SCSI bus. Refer to the hardware manuals for the devices and the host adapter to properly terminate the bus. Unless your system is SCSI Configured AutoMatically (SCAM) capable, you must configure each SCSI device with a different SCSI ID number. Refer to the hardware manuals for the devices to locate where the jumpers of dip switches are for setting SCSI ID numbers. Usually, the host adapter is ID 7.
6.5 SCSI Terminators To ensure reliable communication, the SCSI bus must be properly terminated. Termination is controlled by a set of electrical resistors, called terminators. Terminators must be placed (or enabled) at the two extreme ends of the SCSI bus. All devices that lie between the ends must have their terminators removed (or disabled).
6.6 SDMS Drivers The SDMS device drivers translate an operating system I/O request into a SCSI request. Each Symbios SCSI device driver is operating system specific and is designed to work on standard Symbios chip implementations. We provide PCI SDMS device drivers for the following operating systems: • MS-DOS/Windows • Windows 95/98 • Windows NT - 3.51 and above • OS/2 4.x Warp • SCO UNIX - Open Server 5.0.2 and above • Novell NetWare - 3.12, 4.
82 PCA-6179 User’s Manual
APPENDIX A Programming the Watchdog Timer The PCA-6179 is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments.
A.1 Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes I/O port address 443 (hex). The output data is a time interval value. The value range is from 01 (hex) to 3F (hex), and the related time interval is 1 sec. to 63 sec. 100 Data Time Interval 01 1 sec. 02 2 sec. 03 3 sec. 04 4 sec. • • • • • • 3F 63 sec.
After data entry, your program must refresh the watchdog timer by rewriting I/O port 443 (hex) while simultaneously setting it. When you want to disable the watchdog timer, your program should read I/O port 443 (hex).
102 PCA-6179 User's Manual
APPENDIX B Pin Assignments This appendix contains information of a detailed or specialized nature.
B.
B.
B.
B.
B.5 USB Connector (CN6) 1 6 2 7 3 8 4 9 5 10 Table B-5: USB1/USB2 connector (CN6) Pin USB1 Signal Pin USB2 Signal 1 +5 V 6 +5 V 2 UV- 7 UV- 3 UV+ 8 UV+ 4 GND 9 GND 5 Chassis GND 10 Key B.
B.7 Ethernet 10/100Base-T RJ-45 Connector (CN8) Table B-7: Ethernet 10/100Base-T RJ-45 connector (CN8) Pin Signal Pin Signal 1 XMT+ 5 N/C 2 XMT- 6 RCV- 3 RCV+ 7 N/C 4 N/C 8 N/C B.
B.9 Keyboard and Mouse Connnector (CN11) Table B-9: Keyboard and mouse connector (CN11) Pin Signal 1 KB DATA 2 MS DATA 3 GND 4 VCC 5 KB CLOCK 6 MS CLOCK B.
B.11 IR Connector (CN13) 9 7 5 3 1 10 8 6 4 2 Table B-11: IR connector (CN13) Pin Signal Pin Signal 1 +5 V 2 N/C 3 FIRRX 4 CIRRX 5 IR_RX 6 +5VSB 7 GND 8 N/C 9 IR_TX 10 N/C B.
B.13 Power LED and Keylock Connector (CN16) You can use an LED to indicate when the CPU card is on. Pin 1 of CN16 supplies the LED's power, and Pin 3 is the ground. You can use a switch (or a lock) to disable the keyboard so that the PC will not respond to any input. This is useful if you do not want anyone to change or stop a program which is running. Simply connect the switch from Pin 4 to Pin 5 of CN16.
B.15 Reset Connector (CN18) Table B-15: Reset connector (CN18) Pin Signal 1 GND 2 RESETIN B.16 HDD LED Connector (CN19) Table B-16: HDD LED connector (CN19) Pin Signal 1 VCC (LED+) 2 LED0 (LED-) B.
B.18 System I/O Ports Table B-18: System I/O ports Addr.
B.19 DMA Channel Assignments Table B-19: DMA channel assignments Channel Function 0 Available 1 Available 2 Floppy disk (8-bit transfer) 3 Available 4 Cascade for DMA controller 1 5 Available 6 Available 7 Available B.
B.21 1st MB Memory Map Table B-21: 1st MB memory map Addr. range (Hex) Device F0000h - FFFFFh System ROM C8000h - EFFFFh Unused C0000h - C7FFFh VGA BIOS B8000h - BFFFFh CGA/EGA/VGA text B0000h - B7FFFh Unused A0000h - AFFFFh EGA/VGA graphics 00000h - 9FFFFh Base memory B.
APPENDIX C DiskOnChip® 2000 Installation Guide This appendix contains information on the DiskOnChip® 2000 quick installation guide.
C.1 DiskOnChip® 2000 Quick Installation Guide C.1.1 DiskOnChip® 2000 installation instructions 1. Make sure the target platform is powered OFF. 2. Plug the DiskOnChip® 2000 device into its socket. Verify the direction is correct (pin 1 of the DiskOnChip 2000 is aligned with pin 1 of the socket). 3. Power up the system. 4. During power up you may observe the messages displayed by the DiskOnChip 2000 when its drivers are automatically loaded into the system's memory. 5.
C.1.2 Addtional information and assistance 1. Visit M-Systems' website at http://www.m-sys.com where you can find the Utilities Manual, data sheet and Application Notes. In addition, you can find the latest DiskOnChip 2000 software utilities. 2. Contact your dealer for technical support if you need additional assistance, and have the following information ready: • Product name and serial number. • Description of your computer hardware (manufacturer, model, attached devices, etc.
120 PCA-6179 User's Manual
