User manual
Table Of Contents
- PCA-6011
- Contents
- 1 Hardware Configuration
- 1.1 Introduction
- 1.2 Features
- 1.3 Specifications
- 1.4 Jumpers and Connectors
- 1.5 Board Layout: Jumper and Connector Locations
- 1.6 PCA-6011 Block Diagram
- 1.7 Safety Precautions
- 1.8 Jumper Settings
- 1.9 System Memory
- 1.10 Memory Installation Procedures
- 1.11 Cache Memory
- 1.12 Processor Installation
- 1.13 Power Model Setting and Installation
- 1.14 ATX Mode
- 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 IDE Connectors (IDE1)
- 2.3 Floppy Drive Connector (FDD1)
- 2.4 Parallel Port (LPT1)
- 2.5 VGA Connector (VGA1)
- 2.6 Serial Ports (COM1, COM2)
- 2.7 PS/2 Keyboard and Mouse Connector (KBMS1)
- 2.8 External Keyboard & Mouse (KBMS2)
- 2.9 CPU Fan Connector (CPUFAN1)
- 2.10 Front Panel Connectors (JFP1, JFP2, JFP3)
- 2.11 H/W Monitor Alarm (JOBS1)
- 2.12 LAN RJ45 connector (LAN1/LAN2)
- 2.13 HD Link connector (HDAUD1)
- 2.14 Serial ATA2 Interface (SATA1 ~ SATA4)
- 2.15 LAN LED connector (LAN LED1)
- 2.16 USB (USB12, USB34, USB56, USB78)
- 2.17 Case open (JCASE1)
- 3 AMI BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.2.1 Main Setup
- 3.2.2 Advanced BIOS Features Setup
- 3.2.3 PCI/PNP Setup
- 3.2.4 Boot Settings
- 3.2.5 Security Settings
- 3.2.6 Advanced Chipset Settings
- 3.2.7 Exit Options
- 4 Chipset Software Installation Utility
- 5 VGA Setup
- 6 LAN Configuration
- A Programming the Watchdog Timer
- B I/O Pin Assignments
- B.1 IDE Hard Drive Connector (IDE1)
- B.2 Floppy Drive Connector (FDD1)
- B.3 Parallel Port Connector (LPT1)
- B.4 VGA Connector (VGA1)
- B.5 RS-232 Serial Port (COM1, COM2)
- B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
- B.7 External Keyboard Connector (KBMS2)
- B.8 CPU Fan Power Connector (CPUFAN1)
- B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)
- B.10 External Speaker Connector (JFP2 / SPEAKER)
- B.11 Reset Connector (JFP1 / RESET)
- B.12 HDD LED (JFP2 / HDDLED)
- B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
- B.14 SM Bus Connector (JFP2/SNMP)
- B.15 HD Link connector (HDAUD1)
- B.16 LAN LED Connector (LAN LED1)
- B.17 AT Power Connector (ATXF1)
- B.18 H/W Monitor Alarm (JOBS1)
- B.19 USB Connector (USB12, USB34, USB56, USB78)
- B.20 Case Open Connector (JCASE1)
- B.21 GPIO Pin Header (GPIO1)
- B.22 System I/O Ports
- B.23 DMA Channel Assignments
- B.24 Interrupt Assignments
- B.25 1st MB Memory Map
- B.26 PCI Bus Map
3 PCA-6011 User Manual
Chapter 1 Hardware Configuration
1.3 Specifications
1.3.1 System
CPU: Intel® LGA 775 Core
TM
2 Quad, Core
TM
2 Duo, Celeron® 440 up to 2.66/
3.33/2.2 GHz, (refer to “Processor Support” on page iv), FSB 800/1066/1333
MHz. PCA-6011 also has an optional CPU cooler (1750000332) for customers
who use high-speed CPUs in 2U chassis or in a high-temperature environment.
L2 cache: CPU has built-in 6 MB (for Core™ 2 Quad), 6 MB (for Core
TM
2
Duo), 512 KB (for Celeron 440 CPU) full-speed L2 cache
BIOS: AMI 16 MB SPI Flash
System chipset: Intel G41 + ICH7/ICH7R(Only for G2 SKU)
SATA/EIDE hard disk drive interface: Four on-board SATA2 connectors with
data transmission rate up to 300 MB/s. One on-board IDE connector supporting
up to two
enhanced IDE devices. Supports PIO mode 4 (16.67MB/s data transfer
rate) and ATA 33/66/100 (33/66/100MB/s data transfer rate.) BIOS enabled/dis-
abled.
Floppy disk drive interface: Supports one floppy disk drive, 5¼" (360 KB and
1.2 MB) or 3½" (720 KB, 1.44 MB). BIOS enable/disable.
1.3.2 Memory
RAM:
Up to 4 GB in two 240-pin DIMM sockets. Supports dual-channel DDR3
800/1066 SDRAM.
1.3.3 Input/Output
PCI bus: 32 bit / 33MHz to the backplane
Enhanced parallel port: Configured to LPT1, or disabled. Standard DB-25
female connector provided. Supports EPP/SPP/ECP
Serial ports: Two serial ports on-board. One pin header and one 9-pin D Sub
connector located on the mounting bracket for easy connection
Keyboard and PS/2 mouse connector:
One 6-pin mini-DIN connector is
located on the mounting bracket for easy connection to a keyboard or PS/2
mouse. An on board keyboard pin header connector is also available
USB port: Supports up to eight USB 2.0 ports with transmission rate up to 480
Mbps
1.3.4 Ethernet LAN
Supporting dual 10/100/1000 Mbps Ethernet port(s) via PCI Express x1 bus
which provides 500 MB/s data transmission rate
Controller:
– LAN 1: Intel® 82583V
– LAN 2: Intel® 82583V
1.3.5 Industrial features
Watchdog timer: Can generate a system reset. The watchdog timer is pro-
grammable to 255 levels, with each unit set to equal either one second or one
minute.