User manual
Table Of Contents
- PCA-6011
- Contents
 - 1 Hardware Configuration
- 1.1 Introduction
 - 1.2 Features
 - 1.3 Specifications
 - 1.4 Jumpers and Connectors
 - 1.5 Board Layout: Jumper and Connector Locations
 - 1.6 PCA-6011 Block Diagram
 - 1.7 Safety Precautions
 - 1.8 Jumper Settings
 - 1.9 System Memory
 - 1.10 Memory Installation Procedures
 - 1.11 Cache Memory
 - 1.12 Processor Installation
 - 1.13 Power Model Setting and Installation
 - 1.14 ATX Mode
 
 - 2 Connecting Peripherals
- 2.1 Introduction
 - 2.2 IDE Connectors (IDE1)
 - 2.3 Floppy Drive Connector (FDD1)
 - 2.4 Parallel Port (LPT1)
 - 2.5 VGA Connector (VGA1)
 - 2.6 Serial Ports (COM1, COM2)
 - 2.7 PS/2 Keyboard and Mouse Connector (KBMS1)
 - 2.8 External Keyboard & Mouse (KBMS2)
 - 2.9 CPU Fan Connector (CPUFAN1)
 - 2.10 Front Panel Connectors (JFP1, JFP2, JFP3)
 - 2.11 H/W Monitor Alarm (JOBS1)
 - 2.12 LAN RJ45 connector (LAN1/LAN2)
 - 2.13 HD Link connector (HDAUD1)
 - 2.14 Serial ATA2 Interface (SATA1 ~ SATA4)
 - 2.15 LAN LED connector (LAN LED1)
 - 2.16 USB (USB12, USB34, USB56, USB78)
 - 2.17 Case open (JCASE1)
 
 - 3 AMI BIOS Setup
- 3.1 Introduction
 - 3.2 Entering Setup
- 3.2.1 Main Setup
 - 3.2.2 Advanced BIOS Features Setup
 - 3.2.3 PCI/PNP Setup
 - 3.2.4 Boot Settings
 - 3.2.5 Security Settings
 - 3.2.6 Advanced Chipset Settings
 - 3.2.7 Exit Options
 
 
 - 4 Chipset Software Installation Utility
 - 5 VGA Setup
 - 6 LAN Configuration
 - A Programming the Watchdog Timer
 - B I/O Pin Assignments
- B.1 IDE Hard Drive Connector (IDE1)
 - B.2 Floppy Drive Connector (FDD1)
 - B.3 Parallel Port Connector (LPT1)
 - B.4 VGA Connector (VGA1)
 - B.5 RS-232 Serial Port (COM1, COM2)
 - B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
 - B.7 External Keyboard Connector (KBMS2)
 - B.8 CPU Fan Power Connector (CPUFAN1)
 - B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)
 - B.10 External Speaker Connector (JFP2 / SPEAKER)
 - B.11 Reset Connector (JFP1 / RESET)
 - B.12 HDD LED (JFP2 / HDDLED)
 - B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
 - B.14 SM Bus Connector (JFP2/SNMP)
 - B.15 HD Link connector (HDAUD1)
 - B.16 LAN LED Connector (LAN LED1)
 - B.17 AT Power Connector (ATXF1)
 - B.18 H/W Monitor Alarm (JOBS1)
 - B.19 USB Connector (USB12, USB34, USB56, USB78)
 - B.20 Case Open Connector (JCASE1)
 - B.21 GPIO Pin Header (GPIO1)
 - B.22 System I/O Ports
 - B.23 DMA Channel Assignments
 - B.24 Interrupt Assignments
 - B.25 1st MB Memory Map
 - B.26 PCI Bus Map
 
 
 

43 PCA-6011 User Manual
Chapter 3
A
MI BIOS Setup
3.2.6.2 South Bridge Chipset Configuration
Allows user to set I/O port configurations.
Figure 3.19 South Bridge Chipset Configuration
 USB Functions
Select: Disabled, 2 USB Ports, 4 USB Ports, 6 USB Ports or 8 USB Ports.
 USB 2.0 Controller
Enables or disables the USB 2.0 controller.
 Audio controller
Allows user to choose Auto or Azalia to manage the audio controller.
 SMBUS Controller
Enables or disables the SMBUS controller.
 Reserved Page Route
Allows user to set Port 80 information output port. Available options include PCI,
LPC.
 Restore on AC Power Loss
This option allows user to set system action when AC power restores after AC
power loss. Available options include Power Off, Power On, Last Status.
 Power Type
ATX or AT.
 LAN 1/2 Controller
Enables or disables the LAN 1/2 GbE controller(s). The options below are also
available.
– Boot from LAN1/2
Allows user to enable or disable the function of LAN booting from a PXE server.
– Resume on LAN 1/2
Allows user to enable or disable the function of system resuming from LAN 1/
2.










