User manual
Table Of Contents
- PCA-6011
- Contents
- 1 Hardware Configuration
- 1.1 Introduction
- 1.2 Features
- 1.3 Specifications
- 1.4 Jumpers and Connectors
- 1.5 Board Layout: Jumper and Connector Locations
- 1.6 PCA-6011 Block Diagram
- 1.7 Safety Precautions
- 1.8 Jumper Settings
- 1.9 System Memory
- 1.10 Memory Installation Procedures
- 1.11 Cache Memory
- 1.12 Processor Installation
- 1.13 Power Model Setting and Installation
- 1.14 ATX Mode
- 2 Connecting Peripherals
- 2.1 Introduction
- 2.2 IDE Connectors (IDE1)
- 2.3 Floppy Drive Connector (FDD1)
- 2.4 Parallel Port (LPT1)
- 2.5 VGA Connector (VGA1)
- 2.6 Serial Ports (COM1, COM2)
- 2.7 PS/2 Keyboard and Mouse Connector (KBMS1)
- 2.8 External Keyboard & Mouse (KBMS2)
- 2.9 CPU Fan Connector (CPUFAN1)
- 2.10 Front Panel Connectors (JFP1, JFP2, JFP3)
- 2.11 H/W Monitor Alarm (JOBS1)
- 2.12 LAN RJ45 connector (LAN1/LAN2)
- 2.13 HD Link connector (HDAUD1)
- 2.14 Serial ATA2 Interface (SATA1 ~ SATA4)
- 2.15 LAN LED connector (LAN LED1)
- 2.16 USB (USB12, USB34, USB56, USB78)
- 2.17 Case open (JCASE1)
- 3 AMI BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.2.1 Main Setup
- 3.2.2 Advanced BIOS Features Setup
- 3.2.3 PCI/PNP Setup
- 3.2.4 Boot Settings
- 3.2.5 Security Settings
- 3.2.6 Advanced Chipset Settings
- 3.2.7 Exit Options
- 4 Chipset Software Installation Utility
- 5 VGA Setup
- 6 LAN Configuration
- A Programming the Watchdog Timer
- B I/O Pin Assignments
- B.1 IDE Hard Drive Connector (IDE1)
- B.2 Floppy Drive Connector (FDD1)
- B.3 Parallel Port Connector (LPT1)
- B.4 VGA Connector (VGA1)
- B.5 RS-232 Serial Port (COM1, COM2)
- B.6 PS/2 Keyboard/Mouse Connector (KBMS1)
- B.7 External Keyboard Connector (KBMS2)
- B.8 CPU Fan Power Connector (CPUFAN1)
- B.9 Power LED and Keyboard Lock Connector (JFP3 / PWR_LED & KEY LOCK)
- B.10 External Speaker Connector (JFP2 / SPEAKER)
- B.11 Reset Connector (JFP1 / RESET)
- B.12 HDD LED (JFP2 / HDDLED)
- B.13 ATX Soft Power Switch (JFP1 / PWR_SW)
- B.14 SM Bus Connector (JFP2/SNMP)
- B.15 HD Link connector (HDAUD1)
- B.16 LAN LED Connector (LAN LED1)
- B.17 AT Power Connector (ATXF1)
- B.18 H/W Monitor Alarm (JOBS1)
- B.19 USB Connector (USB12, USB34, USB56, USB78)
- B.20 Case Open Connector (JCASE1)
- B.21 GPIO Pin Header (GPIO1)
- B.22 System I/O Ports
- B.23 DMA Channel Assignments
- B.24 Interrupt Assignments
- B.25 1st MB Memory Map
- B.26 PCI Bus Map
www.advantech.com
Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permis-
sion of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2011