User manual
Table Of Contents
- PCM-3353
- Contents
- 1 General Information
- 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating Connectors
- 2.4 Setting Jumpers
- 2.5 Installing SO-DIMMs
- 2.6 IDE, CDROM Hard Drive Connector (CN11)
- 2.7 Solid State Disk
- 2.8 Parallel Port Connector (CN19)
- 2.9 Keyboard and PS/2 Mouse Connector (CN18)
- 2.10 Power Connectors (CN38)
- 2.11 Audio Interfaces (CN34/35)
- 2.12 COM Port Connector (CN20,CN30)
- 2.13 VGA/LCD Interface Connections
- 2.14 Ethernet Configuration
- 2.15 Watchdog Timer Configuration
- 2.16 USB Connectors (CN15,CN17)
- 2.17 GPIO (General Purpose Input Output) (CN36/ CN37)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Load Optimized Defaults
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit without Saving
- A Pin Assignments
- A.1 Jumper and Connector Tables
- Table A.1: SW1, CF Master / Slave Selector
- Table A.2: J3, Clear CMOS
- Table A.3: CN39, COM2 Setting
- Table A.4: J5, PCI VI/O POWER
- Table A.5: J6, LVDS Power Selector
- Table A.6: CN42, LVDS LCD I/F
- Table A.7: CN38, Power Input
- Table A.8: CN4, TFT LCD I/F
- Table A.9: CN5, Inverter Power
- Table A.10: CN6, SMBus
- Table A.11: CN32, Reset / Buzzer pin header
- Table A.12: CN36, GPIO1
- Table A.13: CN37, GPIO2
- Table A.14: CN11, IDE
- Table A.15: CN27, CRT
- Table A.16: CN15, USB1/2
- Table A.17: CN17, USB3/4
- Table A.18: CN30, COM1/2/3/4
- Table A.19: CN19, Print Port
- Table A.20: CN20, RS422/485
- Table A.21: CN35, AUDIO-OUT
- Table A.22: CN34, AUDIO-IN
- Table A.23: CN23, ISA -5V & -12V Input
- Table A.24: CN26, LAN1
- Table A.25: CN18, KB/MS
- Table A.26: CN40, DDR RAM SOCKET
- Table A.27: CN41, CF SOCKET
- Table A.28: CN33, Battery Connector
- A.1 Jumper and Connector Tables
- B System Assignments
- C Watchdog Timer Sample Code
- D GPIO Sample Code
3 PCM-3353 User Manual
Chapter 1 General Information
1.3.2 VGA/LVDS Interface
Chipset: AMD Geode LX800/LX600
Memory Size: Optimized Shared Memory Architecture, supports 64 MB frame
buffer using system memory
Resolution: CRT resolution: up to 1600 x 1200 x 16 bpp at 100 Hz and up to
1024 x 768 x 32 bpp at 60 Hz for TFT LCD
LCD interface: Supports up to 24-bit TFT LCD (TTL signal)
Supports 18-bit LVDS LCD (supports 24-bit JEIDA LVDS)
Dual simultaneous display: CRT + LCD, CRT + LVDS
1.3.3 Ethernet Interface
Chipset supports: 1 x 10/100 Mbps - Intel 82541PI
Interface: 1 x internal box header
Standard IEEE 802.3u (100 BASE-T) protocol compatible
1.3.4 Audio Function
Audio controller: Realtek ALC 203 chipset, supports AC97 3D Audio stereo
sound
Audio interface: Microphone in, Line in, Line out
1.3.5 OS support
This board supports Win XP, Win CE and Win XPe.
For further information about OS support in your PCM-3353, visit the following
web resource Advantech: website: www.advantech.com or please contact tech-
nical support center
1.3.6 Mechanical and Environmental
Dimensions: 96 x 115 mm (3.77"x 4.05"), Mechanical Drawing (dxf file) is avail-
able.
Power supply type: AT
Power requirement: +5 V ± 5%, +12 V ± 5% (Optional), (5V only, 12V optional
for PC104 add on card and LCD inverter)
Power consumption: (Geode LX800, 256 MB DDR333)
– Max: +5 V @ 1.51 A, +12 V @ 0.1 A
– Typical: +5 V @ 1.35 A, +12 V @ 0.1A
Operating temperature: 0 ~ 60° C (32 ~ 140° F)
Operating humidity: 10% ~ 90% relative humidity, non-condensing
Weight: 0.85 kg (reference weight of total package)