User manual
Table Of Contents
- PCM-3353
- Contents
- 1 General Information
- 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating Connectors
- 2.4 Setting Jumpers
- 2.5 Installing SO-DIMMs
- 2.6 IDE, CDROM Hard Drive Connector (CN11)
- 2.7 Solid State Disk
- 2.8 Parallel Port Connector (CN19)
- 2.9 Keyboard and PS/2 Mouse Connector (CN18)
- 2.10 Power Connectors (CN38)
- 2.11 Audio Interfaces (CN34/35)
- 2.12 COM Port Connector (CN20,CN30)
- 2.13 VGA/LCD Interface Connections
- 2.14 Ethernet Configuration
- 2.15 Watchdog Timer Configuration
- 2.16 USB Connectors (CN15,CN17)
- 2.17 GPIO (General Purpose Input Output) (CN36/ CN37)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Load Optimized Defaults
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit without Saving
- A Pin Assignments
- A.1 Jumper and Connector Tables
- Table A.1: SW1, CF Master / Slave Selector
- Table A.2: J3, Clear CMOS
- Table A.3: CN39, COM2 Setting
- Table A.4: J5, PCI VI/O POWER
- Table A.5: J6, LVDS Power Selector
- Table A.6: CN42, LVDS LCD I/F
- Table A.7: CN38, Power Input
- Table A.8: CN4, TFT LCD I/F
- Table A.9: CN5, Inverter Power
- Table A.10: CN6, SMBus
- Table A.11: CN32, Reset / Buzzer pin header
- Table A.12: CN36, GPIO1
- Table A.13: CN37, GPIO2
- Table A.14: CN11, IDE
- Table A.15: CN27, CRT
- Table A.16: CN15, USB1/2
- Table A.17: CN17, USB3/4
- Table A.18: CN30, COM1/2/3/4
- Table A.19: CN19, Print Port
- Table A.20: CN20, RS422/485
- Table A.21: CN35, AUDIO-OUT
- Table A.22: CN34, AUDIO-IN
- Table A.23: CN23, ISA -5V & -12V Input
- Table A.24: CN26, LAN1
- Table A.25: CN18, KB/MS
- Table A.26: CN40, DDR RAM SOCKET
- Table A.27: CN41, CF SOCKET
- Table A.28: CN33, Battery Connector
- A.1 Jumper and Connector Tables
- B System Assignments
- C Watchdog Timer Sample Code
- D GPIO Sample Code
PCM-3353 User Manual 6
2.1 Jumpers
The PCM-3353 has a number of jumpers that allow you to configure your system to
suit your application. The table below lists the functions of the various jumpers.
2.2 Connectors
Onboard connectors link the PCM-3353 to external devices such as hard disk drives,
a keyboard, or floppy drives. The table below lists the function of each of the board’s
connectors.
Table 2.1: Jumper/Switch Setting
J3 Clear CMOS
J5 PCI VI/O Power Selector
CN39 COM2 Setting
SW1 CF Master / Slave Selector
J6 LVDS Power Selector
Table 2.2: Connector Table
CN4 TFT LCD I/F
CN5 Inverter Power
CN6 SMBus
CN11 IDE
CN15 USB1/2 / CN17 USB 3/4
CN18 KB/MS
CN19 Print Port
CN20 RS422/485
CN23 ISA -5 V & -12 V Input
CN26 LAN
CN27 CRT
CN30 COM1/2/3/4
CN32 Reset / Buzzer pin header
CN33 Battery Connector
CN35 AUDIO-OUT / CN34 AUDIO-IN
CN36 GPIO1
CN37 GPIO2
CN38 Power Input
CN40 DDR RAM Socket
CN41 CF Socket
CN42 LVDS LCD I/F
CN43 Inverter Power (LVDS)