User manual
Table Of Contents
- PCM-3353
- Contents
- 1 General Information
- 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating Connectors
- 2.4 Setting Jumpers
- 2.5 Installing SO-DIMMs
- 2.6 IDE, CDROM Hard Drive Connector (CN11)
- 2.7 Solid State Disk
- 2.8 Parallel Port Connector (CN19)
- 2.9 Keyboard and PS/2 Mouse Connector (CN18)
- 2.10 Power Connectors (CN38)
- 2.11 Audio Interfaces (CN34/35)
- 2.12 COM Port Connector (CN20,CN30)
- 2.13 VGA/LCD Interface Connections
- 2.14 Ethernet Configuration
- 2.15 Watchdog Timer Configuration
- 2.16 USB Connectors (CN15,CN17)
- 2.17 GPIO (General Purpose Input Output) (CN36/ CN37)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Load Optimized Defaults
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit without Saving
- A Pin Assignments
- A.1 Jumper and Connector Tables
- Table A.1: SW1, CF Master / Slave Selector
- Table A.2: J3, Clear CMOS
- Table A.3: CN39, COM2 Setting
- Table A.4: J5, PCI VI/O POWER
- Table A.5: J6, LVDS Power Selector
- Table A.6: CN42, LVDS LCD I/F
- Table A.7: CN38, Power Input
- Table A.8: CN4, TFT LCD I/F
- Table A.9: CN5, Inverter Power
- Table A.10: CN6, SMBus
- Table A.11: CN32, Reset / Buzzer pin header
- Table A.12: CN36, GPIO1
- Table A.13: CN37, GPIO2
- Table A.14: CN11, IDE
- Table A.15: CN27, CRT
- Table A.16: CN15, USB1/2
- Table A.17: CN17, USB3/4
- Table A.18: CN30, COM1/2/3/4
- Table A.19: CN19, Print Port
- Table A.20: CN20, RS422/485
- Table A.21: CN35, AUDIO-OUT
- Table A.22: CN34, AUDIO-IN
- Table A.23: CN23, ISA -5V & -12V Input
- Table A.24: CN26, LAN1
- Table A.25: CN18, KB/MS
- Table A.26: CN40, DDR RAM SOCKET
- Table A.27: CN41, CF SOCKET
- Table A.28: CN33, Battery Connector
- A.1 Jumper and Connector Tables
- B System Assignments
- C Watchdog Timer Sample Code
- D GPIO Sample Code
PCM-3353 User Manual 20
IDE Primary Slave UDMA [Auto]
This item allows adjustment of primary slave IDE mode or type for modification
purposes. Suggested BIOS default value is "Auto".
IDE DMA transfer access [Enabled]
This item allows adjustment of IDE DMA mode. Enabling increases IDE Data
transfer speed. Suggested BIOS default value is "Enabled".
LAN1 controller [Enabled]
This item enables/disables the onboard LAN switch.
ITE8888 Configure [Press Enter]
This item allows user to make detailed ITE8888 adjustments.
IDE HDD Block Mode [Enabled]
This item allows enabling or disabling IDE block data transfer mode. When
enabled, it will speed up HDD data transfer of efficiency. Suggested BIOS
default value is "Enabled".
LPT/FDC switch: [Disabled]
This item enables/disables the LPT/FDC port switch. When enabled, it will
change from LPT to FDC port. Suggested BIOS default value is "Disabled".
Onboard Serial Port 1 [3F8]
This item allows user to change COM 1 address. Suggested BIOS default value
is "3F8".
Onboard Serial Port 1 use [IRQ4]
This item allows user to change COM 1 IRQ. Suggested BIOS default value is
"IRQ4".
Onboard Serial Port 2 [2F8]
This item allows user to change COM 2 address. Suggested BIOS default value
is "2F8".
Onboard Serial Port 2 use [IRQ3]
This item allows user to change COM 2 IRQ. Suggested BIOS default value is
"IRQ3".
Onboard Serial Port 3 [3E8]
This item allows user to change COM 3 address. Suggested BIOS default value
is "3E8".
Onboard Serial Port 3 use [IRQ10]
This item allows user to change COM 3 IRQ. Suggested BIOS default value is
"IRQ10".
Onboard Serial Port 4 [2E8]
This item allows user to change COM 4 address. Suggested BIOS default value
is "3E8".
Onboard Serial Port 4 use [IRQ5]
This item allows user to change COM 4 IRQ. Suggested BIOS default value is
"IRQ5".
Auto Flow Control [Disabled]
This item allows user to control COM port auto flow transfer. Suggested BIOS
default value is "Disabled".
Onboard Parallel Port [378/IRQ7]
This item allows user to change parallel port address. Suggested BIOS default
value is "378/IRQ7".