User manual
Table Of Contents
- PCM-3353
- Contents
- 1 General Information
- 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating Connectors
- 2.4 Setting Jumpers
- 2.5 Installing SO-DIMMs
- 2.6 IDE, CDROM Hard Drive Connector (CN11)
- 2.7 Solid State Disk
- 2.8 Parallel Port Connector (CN19)
- 2.9 Keyboard and PS/2 Mouse Connector (CN18)
- 2.10 Power Connectors (CN38)
- 2.11 Audio Interfaces (CN34/35)
- 2.12 COM Port Connector (CN20,CN30)
- 2.13 VGA/LCD Interface Connections
- 2.14 Ethernet Configuration
- 2.15 Watchdog Timer Configuration
- 2.16 USB Connectors (CN15,CN17)
- 2.17 GPIO (General Purpose Input Output) (CN36/ CN37)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Load Optimized Defaults
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit without Saving
- A Pin Assignments
- A.1 Jumper and Connector Tables
- Table A.1: SW1, CF Master / Slave Selector
- Table A.2: J3, Clear CMOS
- Table A.3: CN39, COM2 Setting
- Table A.4: J5, PCI VI/O POWER
- Table A.5: J6, LVDS Power Selector
- Table A.6: CN42, LVDS LCD I/F
- Table A.7: CN38, Power Input
- Table A.8: CN4, TFT LCD I/F
- Table A.9: CN5, Inverter Power
- Table A.10: CN6, SMBus
- Table A.11: CN32, Reset / Buzzer pin header
- Table A.12: CN36, GPIO1
- Table A.13: CN37, GPIO2
- Table A.14: CN11, IDE
- Table A.15: CN27, CRT
- Table A.16: CN15, USB1/2
- Table A.17: CN17, USB3/4
- Table A.18: CN30, COM1/2/3/4
- Table A.19: CN19, Print Port
- Table A.20: CN20, RS422/485
- Table A.21: CN35, AUDIO-OUT
- Table A.22: CN34, AUDIO-IN
- Table A.23: CN23, ISA -5V & -12V Input
- Table A.24: CN26, LAN1
- Table A.25: CN18, KB/MS
- Table A.26: CN40, DDR RAM SOCKET
- Table A.27: CN41, CF SOCKET
- Table A.28: CN33, Battery Connector
- A.1 Jumper and Connector Tables
- B System Assignments
- C Watchdog Timer Sample Code
- D GPIO Sample Code
iii PCM-3353 User Manual
Declaration of Conformity
FCC Class A
Note: This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications. Opera-
tion of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Technical Support and Assistance
1. Visit the Advantech web site at http://support.advantech.com where you can find
the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service
center for technical support if you need additional assistance. Please have the
following information ready before you call:
– Product name and serial number
– Description of your peripheral attachments
– Description of your software (operating system, version, application software,
etc.)
– A complete description of the problem
– The exact wording of any error messages
Warning! There is a danger of a new battery exploding if it is incorrectly installed.
Do not attempt to recharge, force open, or heat the battery. Replace the
battery only with the same or equivalent type recommendedby the man-
ufacturer. Discard used batteries according to the manufacturer’s
instructions.