User manual
Table Of Contents
- PCM-3353
- Contents
- 1 General Information
- 2 Installation
- 2.1 Jumpers
- 2.2 Connectors
- 2.3 Locating Connectors
- 2.4 Setting Jumpers
- 2.5 Installing SO-DIMMs
- 2.6 IDE, CDROM Hard Drive Connector (CN11)
- 2.7 Solid State Disk
- 2.8 Parallel Port Connector (CN19)
- 2.9 Keyboard and PS/2 Mouse Connector (CN18)
- 2.10 Power Connectors (CN38)
- 2.11 Audio Interfaces (CN34/35)
- 2.12 COM Port Connector (CN20,CN30)
- 2.13 VGA/LCD Interface Connections
- 2.14 Ethernet Configuration
- 2.15 Watchdog Timer Configuration
- 2.16 USB Connectors (CN15,CN17)
- 2.17 GPIO (General Purpose Input Output) (CN36/ CN37)
- 3 Award BIOS Setup
- 3.1 Introduction
- 3.2 Entering Setup
- 3.3 Standard CMOS Setup
- 3.4 Advanced BIOS Features
- 3.5 Advanced Chipset Features
- 3.6 Integrated Peripherals
- 3.7 Power Management Setup
- 3.8 PnP/PCI Configurations
- 3.9 PC Health Status
- 3.10 Load Optimized Defaults
- 3.11 Password Setting
- 3.12 Save & Exit Setup
- 3.13 Exit without Saving
- A Pin Assignments
- A.1 Jumper and Connector Tables
- Table A.1: SW1, CF Master / Slave Selector
- Table A.2: J3, Clear CMOS
- Table A.3: CN39, COM2 Setting
- Table A.4: J5, PCI VI/O POWER
- Table A.5: J6, LVDS Power Selector
- Table A.6: CN42, LVDS LCD I/F
- Table A.7: CN38, Power Input
- Table A.8: CN4, TFT LCD I/F
- Table A.9: CN5, Inverter Power
- Table A.10: CN6, SMBus
- Table A.11: CN32, Reset / Buzzer pin header
- Table A.12: CN36, GPIO1
- Table A.13: CN37, GPIO2
- Table A.14: CN11, IDE
- Table A.15: CN27, CRT
- Table A.16: CN15, USB1/2
- Table A.17: CN17, USB3/4
- Table A.18: CN30, COM1/2/3/4
- Table A.19: CN19, Print Port
- Table A.20: CN20, RS422/485
- Table A.21: CN35, AUDIO-OUT
- Table A.22: CN34, AUDIO-IN
- Table A.23: CN23, ISA -5V & -12V Input
- Table A.24: CN26, LAN1
- Table A.25: CN18, KB/MS
- Table A.26: CN40, DDR RAM SOCKET
- Table A.27: CN41, CF SOCKET
- Table A.28: CN33, Battery Connector
- A.1 Jumper and Connector Tables
- B System Assignments
- C Watchdog Timer Sample Code
- D GPIO Sample Code
PCM-3353 User Manual 22
Max. Power Saving Maximum power management., Suspend Mode =
1 min., and HDD Power Down = 1 min.
User Defined (Default) Allows you to set each mode individually. When not
disabled, each of the ranges are from 1 min. to 1 hr. except for HDD Power
Down which ranges from 1 min. to 15 min. and disable.
Modem Use IRQ
This determines the IRQ which the MODEM can use. The choices: 3, 4, 5, 7, 9,
10, 11, NA.
Power-On by Alarm [Disabled]
This item allows users to power on the system at a specified date and time.
Disabled Disables this function.
Enabled Enables alarm function to power on system Day (of the
month) Alarm 1-31 Time (HH:MM:SS) Alarm (0-23):
(0-59): 0-59)
IRQ Wakeup Events [Press Enter]
This item allows user to control wakeup from an IRQ event.
3.8 PnP/PCI Configurations
Figure 3.7 PnP/PCI configurations screen
PnP OS Installed
Select Yes if you are using a plug and play capable operating system. Select No
if you need the BIOS to configure non-boot device.
Init Display First [Onboard]
This item allows user to change boot display sequence.
PNP OS Installed [No]
Usually best set to No. Some rare cases may need to set to Yes.
Reset Configuration Data [Disabled]
This item allows user to clear any PnP configuration data stored in the BIOS.