POC- 195 Pentium® M processor-based Point of Care Terminal with 19” TFT LCD User’s Manual
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Warning 1. Input voltage rated 100-240 VAC, 50-60 Hz, 4-2 A (AC Mode) 2. Use a 3 V @ 195 mA lithium battery (Model No. BR2032) 3. Packing: please carry the unit with both hands, handle with care 4. Our European representative: Advantech Europe GmbH Kolberger Straße 7 D-40599 Düsseldorf, Germany Tel: 49-211-97477350 Fax: 49-211-97477300 5. Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator Safety Instructions 1.
Supply Class I adapter No applied part IPX1 Continuous Operation Not AP or APG category 19. Disconnect device: Appliance inlet. 20. Follow the national requirement to dispose unit. 21. Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a dry applicator. 22. Contact information: No.1, Alley 20, Lane 26, Reuiguang Road Neihu District, Taipei, Taiwan 114, R.O.C. TEL: (02)27927818 23. 24. This equipment shall not be used for life support system. 25.
Chapter 1General Information 1.1 Introduction The POC-195 is a multimedia Pentium® Mobile processor-based computer that is designed to serve as a Point of Care terminal (POC.) It is a PC-based system with 19" color TFT LCD display, on-board PCI express Ethernet controller, multi-COM port interfaces and 18-bit stereo audio controller. With a built-in CD-ROM drive and mini PCI expansion slot, the POC195 is as compact and user-friendly as a notebook computer.
• • • Audio controller: 18-bit codec, full-duplex stereo codec Audio interface: Microphone-in, Line-in, Line-out Internal Speaker: 1W speaker x 2, Full alarm volume > 70 dB(A) 1 meter Ethernet interface • • Chipset: Marvell 88E8053 PCI express high performance Gigabit Ethernet controller Ethernet interface: Gigabit Ethernet port x 2, full integrated Gigabit Ethernet Media Access Control (MAC) and Physical Layer (PHY) functions, and each provides a standard IEEE 803.
Cleaning/Disinfecting During normal use of the POC-195 may become soiled and should, therefore, be cleaned regularly. Agents: Green tinctured soap and Enzymatic detergents Steps: 1. Wipe the POC-195 with a clean cloth that has been moistened in the cleaning solution. 2. Prepare agent per manufacturer’s instructions or hospital protocol. 3. Wipe thoroughly with a clean cloth Cautions Do not immerse or rinse the POC-195 and its peripherals.
2.1 A Quick Tour of the POC-195 Before you start to set up the POC-195, take a moment to become familiar with the locations and purposes of the controls, drives, connections and ports, which are illustrated in the figures below. When you place the POC-195 upright on the desktop, its front panel appears as shown in Figure 2-1.
A B B D E F G H I Isolated RS-232 COM port (COM1 /COM2/COM3 ) PS/2 Mouse/Keyboard Port IEEE-1394a Port Parallel Port Line-out/Line-in/MIC-in Port ( From left to right) D-sub VGA port USB 2.0 Ports RJ-45 Gigabit LAN Port Functional Earth Ground Connector Figure 2-3: Rear view of the Point of Care Terminal 2.2 Installation Procedures 2.2.1 Connecting the power cord Be sure to always handle the power cords by holding the plug ends only. Follow these procedures in order: 1.
Figure 2-5: Connecting the power cord 2.2.2 Connecting the keyboard and mouse 1. Connect the Y-shaped adapter to the PS/2 mouse and keyboard port on the I/O section of the POC-195. (See Figure 2-6.) 2. Connect the PS/2 mouse and keyboard to the Y-shaped adapter. (See Figure 2-12.) If you use a serial mouse, you can connect the mouse to any COM port in the I/O section. 2.2.3 Switching on the power Switch on the power switch on the rear cover 2.
If required, insert your operating system's installation or setup diskette into the optical drive until the release button pops out. (See Figure 2-14) The BIOS supports system boot-up directly from the CD-ROM drive. You may also insert your system installation CD-ROM disk into the CD-ROM drive.. Power on or reset the system by pressing the "Ctrl"+"Alt"+"Del" keys simultaneously. The Point of Care Terminal will automatically load the operating system from the diskette or CDROM.
Max memory allocation support based on total system memory 1-MB or 8 MB of pre-allocated memory supported. 3.1.3 LVDS Transmitter The POC-195 uses Chrontel CH7308A for driving its LCD panel. The CH7308A is a display controller device, which accepts digital graphics input signals, upscales, encodes, and transmits data through an LVDS transmitter to a LCD panel. The CH7308A operates at pixel rates of up to 140MHz, and support 18-bit/24-bit LCD panels. 3.1.
Step 1-3 Read License Agreement and click ‘Yes’ to proceed. Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart your computer.
Step 2-1 Click the 'Start' button in the task bar, click 'Run' and then select ‘Setup.exe’ from the drive directory “D://VGA/” where the driver files are stored. The Install dialog will appear. Step 2-2 click 'Next' to continue.
Step 2-3 Read License Agreement and click ‘Yes’ to proceed. Step 2-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart your computer.
3.3 Further information For further information about the VGA installation in your POC-195, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. Intel website: www.intel.com.tw Advantech websites: www.advantech.com www.advantech.com.tw Chapter 4 Audio Interface 4.1 Introduction The POC-195's onboard audio interface provides high-quality stereo sound and FM music synthesis (ESFM) by using the ALC202 audio controller from Realtek.
Note2 means pressing the “Enter” key on the keyboard. 4.2.1 Installation for Windows 2000/XP Step 1-1 Click the 'Start' button in the task bar, click 'Run' and then select ' infinst_autol.exe' from the drive directory “D://Audio/” where the driver files are stored. The Install dialog will appear. Step 1-2 click 'Next' to continue. Step 1-3 click 'Next' to continue.
Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart your computer. 4.3 Further information For further information about the Audio interface installation in your POC-195, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. Realtek website: www.realtek.com.tw Advantech websites: www.advantech.com www.advantech.com.tw Chapter 5 Touch screen Interface 5.1 Introduction 5.1.
Step 1-1 Click the 'Start' button in the task bar, click 'Run' and then select ' sw500930.exe' from the drive directory “D://Elotouch/” where the driver files are stored. The Install dialog will appear. Step 1-2 click 'Ok' to continue. Step 1-3 click 'Unzip' to continue. Step 1-4 click 'Ok' to continue.
Step 1-5 click 'Next' to continue. Step 1-6 Read License Agreement and click ‘Yes’ to proceed.
Step 1-7 click 'Next' to continue. Step 1-8 click 'Next' to continue.
Step 1-9 click 'Next' to continue.
Step 1-10 When the 'Setup COMPLETE' message appears click 'Finish'. And follow up the software guiding to complete touch screen calibration procedures.
5.3 Further information For further information about the Touchscreen installation in your POC-195, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. Elo website: www.elotouch.com Advantech websites: www.advantech.com www.advantech.com.tw Chapter 6 PCI Express Ethernet Interface 6.1 Introduction The POC-195 is equipped with a high performance PCIe Ethernet chipset Marvell 88E8053 which is fully compliant with IEEE 802.3 10/100/1000 Mbps standards.
Step 1-3 click 'Next' to continue. Step 1-4 When the 'Setup COMPLETE' message appears click 'Finish' to restart your computer.
6.3 Further information For further information about the Ethernet installation in your POC-195, included Driver updates, troubleshooting guides and FAQ lists please visit the following web resources. Marvell website: www.marvell.com Advantech websites: www.advantech.com www.advantech.com.
