User Manual PPC-4211W Intel® Core i processor based microcomputer, with 21.
Copyright The documentation and the software included with this product are copyrighted 2014 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure.
Safety Instructions 1. 2. 3. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
PPC-4211W User Manual vi
Contents Chapter 1 General Information ............................1 1.1 1.2 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 1.2.1 General Specification.................................................................... 2 1.2.2 Power Specifications..................................................................... 3 1.2.
2.11 Figure 2.30ATX mode ................................................................ 14 Figure 2.31AT mode................................................................... 14 Grounding Installation ............................................................................. 15 Figure 2.32 ................................................................................. 15 Figure 2.33 ................................................................................. 15 Figure 2.34 ...................
Chapter 1 1 General Information This chapter gives background information on the PPC-4211W panel PC.
1.1 Introduction The PPC-4211W is a new generation Panel PC with WXGA (1920 x 1080) screen. The system is equipped with a high performance Intel Core i CPU and with a high efficiency fanless thermal design the heat is easily dissipated. This gives HMI a big step forward in consolidating performance and reliability in one system. Besides, with multiple I/O ports (five COM, five USB and two Gigabit ethernet) its easier to connect to devices and be integrated into machine building industry.
Power i7: 71 W (test system: Windows7 64bit) i5: 66 W (test system: Windows7 64bit) Celeron: 58 W (test system: Windows7 64bit) Output Voltage 12-32 VDC, 8~3 A The above test conditions are detailed in Note 1. 1.2.3 Touchscreen Specifications Type 5-point projected capacitive touchscreen (multi-touch function is only supported in Win 7/WES7P/Win 8/Win 8.1 OS) Light Transmission 88%+/-5% Controller USB interface 1.2.
1.3 Dimensions 548.81 7.50 63.80 41.70 349.80 340.21 558.40 Ø100 Ø75 341.80 550.30 Figure 1.1 PPC-4211W dimensions Note! Supports VESA 100 x 100mm & 75 x 75mm; please use M4 screw, 6 mm depth (maximum). Use suitable mounting apparatus to avoid risk of injury.
Chapter 2 2 System Installation & Setup Sections include: Quick Installation Guide Installation Procedures Installing Memory Installing HDD Installing Mini SATA Installing Wireless LAN Installing Expansion Card AT/ATX Function Switch Grounding Installation Hook Installation Independent Quick Installation
2.1 Quick Start Guide Before you start to set up the panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the panel PC upright on the desktop, its front panel appears as shown in Figure 2.1. 1 Figure 2.1 Front panel 1. 2. 3. I Key Home Key Power status indicator, off (S5): orange, on (S0): blue 5 3 6 1 4 2 1. 2. 3. 4. 5. 6. Figure 2.
C B E H D G I System Installation & Setup F A Figure 2.3 Location of I/O interfaces A: Power button B: Line out/Mic in C: 4 x USB 3.0 D: 2 x Giga Ethernet E: VGA F: DP G: 4 x COM RS232 H: DC power(12-32 V) I: 1 x COM RS422/485 J: PCI/PCIE x4 Expansion slot (refer to Fig 2.4) K: Grounding screw (refer to Fig 2.5) J K Figure 2.4 PCI/PCIe expansion slot Figure 2.
2.2 Installation Procedures 2.2.1 Connecting the Power Cable The panel PC has DC power socket (12-32 V). When connecting the power cable, please hold the plug end. Please follow the procedures below: 1. Connect the female end of the power cable to panel PC’s DC socket. 2. Connect the male end of the power cable to power outlet. Figure 2.6 Connecting the power cable 2.2.2 Connecting the Keyboard and Mouse Connect the keyboard and mouse to panel PC’s I/O interfaces. 2.2.
1. 2. Figure 2.7 Figure 2.8 Figure 2.9 Figure 2.10 Remove the yellow warning tag first. Then remove the screws as indicated in the red circle. (See Fig 2.11), and take out the CPU heatsink. Note! Take out the black and gray thermal grease from the accessary box (as indicated in Figure 2.12). Attach the CPU heatsink after the grease is applied. Figure 2.11 Note! Figure 2.12 CPU cooler pad surface is isolated by anodization treatment to avoid static electricity (CPU contact side excluded).
2.4 Installing the HDD 1. 2. 3. 4. Follow the procedures in Section 2.3 to open the rear cover and remove the screws as indicated in the red circles in Fig 2.13. Remove the HDD bracket from the strength-plate. (See Fig 2.14 and Fig 2.15) Install the HDD (see Fig 2.16 and Fig 2.17), and take out the 4 screws from the accessory box to fix the HDD and then fix the strength-plate (8 screws will be needed if using two HDDs). Lock the HDD bracket, and connect the HDD cable to the mainboard. (See Fig 2.
1. 2. 3. Follow the procedures in Section 2.3 to remove the rear cover and strengthplate. (See Fig 2.19) Plug the MiniSATA into the mainboard interface, and remove the 2 M2.5x4 screws from the accessory box to fix it (See Fig 2.20). Return the rear cover and strength-plate. Chapter 2 2.5 Installing Mini SATA System Installation & Setup Figure 2.19 Figure 2.
2.6 Installing Wireless LAN Card 1. Follow the procedures in Section 2.3 to open the rear cover and strength-plate. The wireless LAN card can be installed to the locations as indicated in Fig 2.21 and 2.22; for the wireless short card, you need to take out one hexagonal screw from the accessory box to fix it. Figure 2.21 2. 3. 4. Figure 2.22 Connect the wireless LAN card module cable to the antenna bracket, please note the installation direction of cable end and screws/cushions. (See Fig 2.
Chapter 2 System Installation & Setup Figure 2.
2.7 Installing the Riser Card 1. 2. 3. Remove the rear cover of the Panel PC. Then remove the screws and shield as indicated in the red circle in Fig 2.26 and install the expansion card. The original machine provides PCIe x4 riser card (PCM-939), and the installation is shown as Fig 2.26 and 2.27). The installation of expansion PCI riser card is shown as Fig 2.28 and Fig 2.29. Note! The maximum dimensions of the expansion card is 167.65 mm x 106.7mm. Figure 2.26 Figure 2.27 Figure 2.28 Figure 2.29 2.
Loosen the screws, remove down the plastic cover, plug in the grounding cable, and then fix the screws. (See Fig 2.32 ~ Fig 2.35) Figure 2.33 Figure 2.34 Figure 2.35 The grounding cable is not provided in the accessory box. 15 PPC-4211W User Manual System Installation & Setup Note! Figure 2.32 Chapter 2 2.
2.10 Hook Installation Follow the figures below: Hook Put the machine into the carbinet, and prepare the hook. Install the hook into the hole to hold the machine as shown above Screw Secure the machine by fastening the screws Figure 2.
Users can independently complete the panel wallmount installation by quick installation Guide. Follow the procedures below: 1. Loosen the two screws at the base, see the figure below. Push the machine into a gap in the wall, the spring hook will lock the machine into the wall. 17 PPC-4211W User Manual System Installation & Setup 2. Chapter 2 2.
3. Installation is complete as shown in the figure below. Then in the rear of the machine, lock the hook screw and fix the machine according to Section 2.10 “Hook Installation”. Note! It is recommend that the mount thickness is smaller than 2 mm (0.079”) according to quick installation guide. For other situations, the recommended thickness is less than 6 mm (0.236”).
Chapter 3 3 Jumper Configuration Sections include: Jumper & Connectors External COM Port Pin Definition
3.1 Jumper & Connectors SW1 CN17 CN20 CN15 CN45 CN46 SW2 Figure 3.1 PCM-8209 front view SW1 Panel Resolution Selection Setting Function 1000 for 15.6" LCD 1110 for 21.
Chapter 3 CN17 clean CMOS Setting Function (1-2) Clear CMOS (2-3) Keep CMOS (default) Jumper Configuration SW2 ATX/AT Mode Selection Pin Pin Name 1-3 ATX Power(default) 2-3 AT Power CN15 GPIO Pin Pin Name 1 GND 2 GPIO4 3 GPIO0 4 GPIO5 5 GPIO1 6 GPIO6 7 GPIO2 8 GPIO7 9 GPIO3 10 5V 21 PPC-4211W User Manual
3.2 External COM Port Pin Definition COM1~4 COM5 Figure 3.2 COM ports COM 1 and COM 2 (RS232, pin9 supports 5 V/12 V output) COM 3 and COM 4 (RS232) COM 5 RS-422/485 Note! COM4 doesn’t support RING function.
Pin 1 3 4 RX+ RX- RS422 TX+ TX- RS485 D+ D- 5 GND GND UART RS485 Auto Flow Control COM5 supports RS485 auto flow control function for all UART. When enabling the RS485 auto control function, it will automatically drive RTS# pin to logic high or low for flow control.
PPC-4211W User Manual 24
Chapter 4 Software Configuration Sections include: Installing Drivers BIOS Setup Program 4
4.1 Install Divers When first using the system, users need to set up corresponding drivers, in order to ensure all functions are normal. Remove the DVD-ROM from the accessory box and open it in the system: Follow the instructions to install the drivers. The drivers in the accompanied DVDROM may not be the latest version, if needed, find it at: http://www.advantech.com/ 4.2 BIOS Setup 4.2.1 Enter BIOS Start the computer and press the “Delete” key to enter BIOS.
Chapter 4 4.2.2 Display Brightness Adjustment Select “Brightness Control” under “Chipset”. 2. Select “Brightness Manual Control” under “Brightness Control”, and there will be six [6] options: Note! If you want to adjust brightness through AP in the OS, it will keep AP configuration mainly, and BIOS configuration will not be saved. 27 PPC-4211W User Manual Software Configuration 1.
4.2.3 COM5 Mode Selection (RS422/485) 1. Select “Super IO Configuration” under “Advanced”. 2. Select “Serial Port 5 Configuration” and then select the operation mode of COM5 by "Serial Port5 Mode".
Select “ACPI Settings” under “Advanced”. 2. Set “Wake On By LAN or RI” as “Enabled”. Software Configuration 1. Chapter 4 4.2.
3. 4. Then save the configuration and exit the OS. Right click “Computer” and click “Manage”, then open “Computer Management”.
6. Select “Work On Magic Packet”, “Work On Pattern Match” and “Work On Magic Packet From Power Off State” under “Power Management”. Software Configuration Click “Network adapters” in “Device Management”, then right click and select the needed LAN port, then select “Properties” and open “Intel(R) Ethernet”. Chapter 4 5.
4.2.5 RAID Installation 1. Enter BIOS when boot up, and click “SATA Configuration” under Advanced. 2. Set “SATA Mode Selection” as “RAID”, then save and exit.
4. Enter “Create RAID Volume”. Software Configuration Press “Ctrl + I” to enter RAID configuration utility when entering the second start-up screen. Chapter 4 3.
5. Input “Name” and select “RAID Level”, and then save and exit “Create Volume” menu. 6. Click “Exit”, the device will start the normal RAID installation.
8. Select RAID driver folder and click “OK”. 35 Software Configuration Take out the OS setup disk when you see this screen, then insert the driver disk and click “Load driver”. Chapter 4 7.
9. Click “Next”. 10. Replace the driver disk with system setup disk after installation of RAID driver is finished, then click “Next” to return the normal system installation.
37 PPC-4211W User Manual Software Configuration 12. Click the icon in the lower-right corner of the screen to check the working status of RAID Volume. Chapter 4 11. After installing all the drivers, click the “SetupRST.exe” in the driver folder.
13. If RAID 1 mode is installed and when one the HDDs fails, a pop-up message will appear in the lower right corner. Click the message box to check details of the problem. 14. At this time, you will need to turn off the computer to change the failed HDD. After entering the system, click “Rebuild to another disk” to back up the system to the new hard disk.
Chapter 4 15. When the rebuilding status shows 100%, system backup is complete and RAID 1 function will work again.
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
