PPC-L156T Pentium M and Celeron M processor based Panel PC with 15" LCD User Manual
Copyright This document is copyrighted, © 2006. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable.
FCC Class B This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with this user's manual, it may cause harmful interference to radio communications.
Packing List Before you begin installation, please make sure that the following materials have been shipped: • PPC-L156T series Panel PC • User manual • Accessories for PPC-L156T - HDD bracket module - Power cord (1.8 m) - USA type (other types are available on request) - Mounting kits and packet of screws - Warranty card - AC/DC power adapter If any of these items are missing or damaged, contact your distributor or sales representative immediately. Additional Information and Assistance Step 1.
Warning! 1 Input voltage rated 100 ~ 240 V, 60/50 Hz at 1.5 A for external power adaptor 2 Input voltage rated 18 ~ 25 V DC at 3.16 A maximum for power supply 3 Use the Spectrum brand (Rayovac), type BR20324. 4 Packing: please carry the unit with both hands, handle with care 5 Maintenance: to properly maintain and clean the surfaces, use only approved products or clean with a dry applicator 6 CompactFlash: Turn off power before inserting or removing CompactFlash storage card.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
Wichtige Sicherheishinweise 1. Bitte lesen sie Sich diese Hinweise sorgfältig durch. 2. Heben Sie diese Anleitung für den späteren Gebrauch auf. 3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein angefeuchtetes Tuch zur Reinigung. 4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein. 5. Das Gerät ist vor Feuchtigkeit zu schützen. 6.
Caution! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer's instructions.
Contents Chapter 1 General Information ........................................2 1.1 1.2 1.3 Chapter Introduction ....................................................................... 2 General Specifications....................................................... 3 Dimensions........................................................................ 7 2 System Setup...................................................10 2.1 2.2 A Quick Tour of the Panel PC ........................................
B.2 B.3 B.4 B.5 B.6 B.7 B.8 B.9 B.10 B.11 USB port (CN20) ............................................................ 38 COM1 RS-232 serial port (CN24) .................................. 38 COM2 (CN25)................................................................. 39 COM3 RS-232 serial port (CN26) .................................. 39 Parallel Port Connector (CN12) ...................................... 40 VGA Connector (CN27) ................................................. 41 GPIO connector (CN13)...
CHAPTER 1 General Information This chapter gives background information on the PPC-L156T panel PC.
Chapter 1 General Information 1.1 Introduction The PPC-L156T panel PC is a multimedia Pentium M and Celeron M processor-based computer that is designed to serve as a human machine interface (HMI) and as a desktop computer. It is a PC-based system with 15" color TFT LCD, on-board PCI Ethernet controller, multiple COM ports, and a 16-bit stereo audio controller. With a built-in CD-ROM drive, floppy drive and PCMCIA expansion sockets, the PPC-L156T is as compact and user-friendly as a notebook computer.
1.2 General Specifications General • Dimensions (W x H x D): 415 x 333 x 76.5 mm (16.3" x 13.1" x 3.0") • Weight: 6 kg (13.2 lb) • Power adapter: AC/DC • Power adaptor output: 19 V at 3.16 A • Disk drive housing: Space for one 2.5" HDD, one slim type CD-ROM (Optional) • Front panel: IP65 protection, NEMA4 compliant Standard PC functions • CPU: Intel Celeron M 600 MHz or Pentium M 1.
• Solid State Disk: Supports one 50-pin socket for CFC type I/II • Watchdog timer: 255-level timer intervals, from 15 sec to 14835 sec, setup by software, jumperless selection, generates system reset • Battery: 3.0 V @ 195 mA lithium battery Spectrum brand (Rayovac), type BR2032 • Power management: Supports power saving modes including Normal/ Standby/Suspend modes. APM 1.
Touchscreen (Optional) Type Resolution Light Transmission Controller Power Consumption Analog Resistive Capacitive Infrared Continuous 1024 x 1024 4096 x 4096 80% 91% 91% RS-232 interface (uses COM4) <5 V @ 200 mA Software Driver Durability (touches in a lifetime) 5V @ 100 mA 5V @ 100 mA Supports Windows 2000/XP 35 million 225 million 100,000 hrs LCD Specifications Display Type 15" TFT LCD Max. Resolution 1024 x 768 Colors 262K Dot Size 0.297 x 0.
Optional modules • Memory: 128/256/512/1024 MB SDRAM • HDD: 2.5" HDD • Touchscreen: Analog resistive, capacitive, or Infrared • CD-ROM drive: Compact 24X CD-ROM or above • DVD-ROM drive: Compact 6X DVD-ROM or above • PCMCIA interface: Complies with 1995 PCMCIA card standard. Supports two PCMCIA card/CardBus slots. Two sockets support both a 16-bit PCMCIA card and a 32-bit CardBus simultaneously. Hot insertion and removal.
1.3 Dimensions 333.3 66.2 312.7 10.0 414.6 394.7 395.5 313.5 CUTOUT Panel Mount (PPC-L156T) Unit : mm Figure 1.
PPC-L156T User Manual 8
CHAPTER 2 System Setup This chapter details system setup on the PPC-L156T Panel PC.
Chapter 2 System Setup 2.1 A Quick Tour of the Panel PC Before you start to set up the panel PC, take a moment to become familiar with the locations and purposes of the controls, drives, connectors and ports, which are illustrated in the figures below. When you place the panel PC upright on the desktop, its front panel appears as shown in Figure 2-1. Figure 2.1: Front view of PPC-L156T panel PC When you turn the panel PC around and look at its rear cover, you will find the I/O section as shown in Fig. 2-2.
VGA Port USB Ports Ethernet Jack Line In PS/2 Mouse and Keyboard Line out Serial Ports Microphone In Parallel Port Figure 2.2: Bottom view of the panel PC Hard Disk Drive CF Socket CD-ROM Option PCMCIA Socket PCMCIA Eject Button Figure 2.
HDD & CF Card Cover PCI Expansion Slot Cover Battery Cover Product Label Figure 2.4: Rear view of the panel PC 2.2 Installation Procedures 2.2.1 Connecting the power cord The panel PC can only be powered by a DC electrical outlet. Be sure to always handle the power cords by holding the plug ends only. Please follow Figure 2-5 to plug the power cord into the DC inlet of the panel PC. Use an M3 screw to fix the power clamp. You can find the power cord, adapter, and power clamp in the accessory box. 2.2.
M3 Screw Power Adapter Power Clamp Figure 2.5: Connect the power cord to the DC inlet 2.3 Running the BIOS Setup Program Your panel PC is likely to have been properly set up and configured by your dealer prior to delivery. You may still find it necessary to use the panel PC's BIOS (Basic Input-Output System) setup program to change system configuration information, such as the current date and time or your type of hard drive. The setup program is stored in read-only memory (ROM).
2.4 Installing System Software Recent releases of operating systems from major vendors include setup programs which load automatically and guide you through hard disk preparation and operating system installation. The guidelines below will help you determine the steps necessary to install your operating system on the panel PC hard drive. Note: Some distributors and system integrators may have already pre-installed system software prior to shipment of your panel PC.
2.4.4 Method 4: Use a USB Disk or USB CD-ROM You can use a USB disk or USB CD-ROM to download the software to your HDD. 2.5 Installing the Drivers After installing your system software, you will be able to set up the Ethernet, XGA, audio, PCMCIA, and touchscreen functions. All drivers are stored in a CD-ROM disc entitled “Drivers and Utilities” which can be found in your accessory box.
PPC-L156T User Manual 16
CHAPTER 3 Hardware Installation and Upgrading This chapter details installing the PPCL156T panel PC hardware. Sections include: • Overview of Hardware Installation and Upgrading • Installing the 2.
Chapter 3 Hardware Installation and Upgrading 3.1 Introduction The panel PC consists of a PC-based computer that is housed in a plastic rear panel and a metal shielding case. You can install a HDD, SDRAM module, CF card, MiniPCI card, and battery pack by removing the rear panel and shielding case. Any maintenance or hardware upgrades can be easily completed after removing the rear panel and shielding case.
1. Detach and remove the plastic HDD cover. Figure 3.1: Removing the HDD cover 2. Get the HDD bracket module from assembly box. 3. Place the HDD in the HDD bracket module and tighten the screws on the two side’s brackets. Figure 3.2: Installing the 2.
4. Place the HDD on the metal plate, and tighten the screws. Figure 3.3: Installing primary 2.5" HDD 5. The HDD cable (1 x 44-pin to 1 x 44-pin) is next to the Mini PCI socket, Connect the HDD cable to the PC board (CN6). Make sure that the red wire corresponds to Pin 1 on the connector, which is labeled on the board. Plug the other end of the cable into the IDE hard drive, with Pin 1 on the cable corresponding to pin 1 on the hard drive. 6. Put the plastic HDD cover and tighten the screws.
3.3 Installing the battery pack 1. Detach and remove the metal battery cover. 2. Put the battery pack in, and then connect the battery cable to the battery connector (PC board –CN11). Make sure that the red wire corresponds to Pin 1 on the connector, which is labeled on the board. 3. Put the metal battery cover and tighten the screws. Figure 3.
3.4 Installing the DDR SDRAM Memory Module You can install from 128 to 1024 MB of DDR SDRAM memory. The Panel PC system provides two 200 pin DDR SODIMM sockets and supports 2.5 V DDR SDRAM. 1. Detach and remove the plastic HDD cover. 2. Detach and remove the plastic rear cover. 3. Insert the memory in the correct location.
CHAPTER 4 Jumper Settings and Connectors This chapter tells how to set up the panel PC hardware, including instructions on setting jumpers and connecting peripherals, switches and indicators. Be sure to read all the safety precautions before you begin the installation procedures.
Chapter 4 Jumper Settings and Connectors 4.1 Jumpers and Connectors 4.1.1 Setting jumpers You can configure your panel PC to match the needs of your application by setting jumpers. A jumper is the simplest kind of electrical switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper, you connect the pins with the clip. To “open” a jumper you remove the clip.
4.1.2 Locating jumpers and switches The motherboard of the PPC-L156T has a number of jumpers that allow you to configure your system to suit your applications. JP1 SW1 JP3 JP4 Label Function JP1 Watchdog timer configuration JP3 LCD voltage setting JP4 COM2 RS-232/422/485 setting SW1 Clear CMOS Figure 4.
4.1.3 Locating connectors The motherboard of the PPC-L156T has a number of connectors that allow you to link external devices such as external hard disk drives.
4.2 CMOS Clear for External RTC (S1) Warning! To avoid damaging the computer, always turn off the power supply before setting “Clear CMOS”. Set the jumper back to “Normal operation” before turning on the power supply. This switch is used to erase CMOS data and reset system BIOS information. The procedure for clearing CMOS is: 1. Turn off system. 2. Push SW1. 3. Turn on the system. The BIOS is now reset to its default setting.
4.3 COM Port Interface The panel PC provides three serial ports (COM1, 3: RS-232; COM2: RS232/422/485) in one COM port connector. 4.3.1 COM2 RS-232/422/485 setting (JP4) COM2 can be configured to operate in RS-232, RS-422, or RS-485 mode. This is done via JP4. Table 4.
4.3.2 COM port address & IRQ settings The default COM port settings are as follows. Table 4.2: Serial port default settings Port Address Range Interrupt COM1 3F8 ~ 3FF IRQ4 COM2 2F8 ~ 2FF IRQ3 COM3 3E8 ~ 3EF IRQ10 COM4 2E8 ~ 2EF IRQ5 COM ports can be disabled or have their IRQ and address ranges changed in the BIOS setup utility. COM1 and COM2 are one set. You can exchange the address range and interrupt of COM1 for the address range and interrupt of COM2.
PPC-L156T User Manual 30
Appendix A GPIO & Watchdog Timer This appendix gives details of programming the GPIO and watchdog timer.
Appendix A GPIO & Watchdog Timer The PPC-L156T is equipped with a watchdog timer that resets the CPU or generates an interrupt if processing comes to a standstill for any reason. This feature ensures system reliability in industrial standalone or unmanned environments. A.1 Supported GPIO Registers Bellow are detailed description of the GPIO addresses and programming sample. A.1.1 GPIO Registers CRF0 (GP10-GP17 I/O selection register.
A.1.2 GPIO Example program-1 -----------------------------------------------Enter the extended function mode, interruptible double-write -----------------------------------------------MOV DX,2EH MOV AL,87H OUT DX,AL OUT DX,AL --------------------------------------------------------------Configured logical device 7(GP10~GP17), configuration register CRF0, CRF1, CRF2 --------------------------------------------------------------MOV DX,2EH MOV AL,07H; point to Logical Device Number Reg.
OUT DX,AL MOV DX,2FH MOV AL,??H; Put the output value into AL ??H OUT DX,AL -----------------------------------------Exit extended function mode | -----------------------------------------MOV DX,2EH MOV AL,AAH OUT DX,AL PPC-L156T User Manual 34
A.2 Watchdog programming Bellow is a sample of programming code for controlling the Watchdog Timer function.
MOV DX,2EH MOV AL,F6H OUT DX,AL MOV DX,2FH MOV AL,05H; Set 5 seconds OUT DX,AL ;-----------------------------------------; Exit extended function mode | ;-----------------------------------------MOV DX,2EH MOV AL,AAH OUT DX,AL PPC-L156T User Manual 36
Appendix B I/O Pin Assignments
Appendix B Pin Assignments B.1 Keyboard and PS/2 Mouse Connector (CN23) Table B.1: Keyboard and mouse connector (CN23) Pin Signal 1 2 3 4 5 6 KB_DAT MS-DAT GND +5 V KB_CLK MS-CLK B.2 USB port (CN20) Table B.2: USB port (CN20) Pin Signal 1 2 3 4 VCC DATADATA+ GND B.3 COM1 RS-232 serial port (CN24) Table B.
B.4 COM2 (CN25) Table B.4: COM2 (CN24) Pin Signal RS-232 RS-422 RS-485 1 2 3 4 5 6 7 8 9 DCD RX TX DTR GND DSR RTS CTS RI TXTX+ RX+ RXGND DATADATA+ B.5 COM3 RS-232 serial port (CN26) Table B.
B.6 Parallel Port Connector (CN12) Table B.
B.7 VGA Connector (CN27) Table B.7: VGA connector (CN27) Pin Signal 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 RED GREEN BLUE N/A GND GND GND GND N/A GND N/A SPDAT HSYNC VSYNC SPCLK B.8 GPIO connector (CN13) Table B.
B.9 USB3, USB4 (CN16) 2 4 1 6 8 10 3 5 7 9 Table B.
B.10 PCI BUS connector Table B.10: PCI BUS connector 5 V System Environment 5 V System Environment Pin Side B Side A Pin Side B 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 -12 V TCK Ground TDO +5 V +5 V INTB# INTD# PRSNT1# Reserved PRSNT2# Ground Ground Reserved Ground CLK Ground REQ# +5 V (I/O) AD[31] AD[29] Ground AD[27] AD[25] 3.3 V C/BE[3]# AD[23] Ground AD[21] AD[19] +3.3 V TRST +12 V TMS TDI +5 V INTA# INTC# +5 V Reserved +5 V Reserved Ground Ground 3.
B.11 PCI Bus connector (PCI1) Figure B.
