Installation Guide

Can Changeover
Once started, do not remove applicator gun from can until can is empty. Point applicator gun in a safe direction and purge
the applicator barrel. Remove can by rotating can in a counter- clockwise direction. Clean applicator basket with AdvanTech
™
polyurethane cleaner as needed. Immediately attach new can of AdvanTech
™
subfl oor adhesive.
Coverage and Curing
One 24 oz. can of AdvanTech
subfl oor adhesive yields
approximately 400 linear feet of
gel adhesive at a ½" diameter
bead. When compared to a 28
oz. caulk cartridge of typical
subfl oor adhesive, product yield
per container is approximately
8 times that of the conventional
adhesive applied at a 3/8" bead, per
manufacturer’s instructions. The
subfl oor panel should be installed
and fastened within 20 minutes
from the time of application.
Storage and Handling
Turn off the fl ow to the gun using
the control knob at the back of the
gun. Store the can in the upright
position with the gun attached. To
resume installation, shake the can
for 30 seconds and then open the
fl ow control value. Maximum storage
is 30 days. Product will keep for 18
months in unopened can when stored between 60° F and 90° F (16° C and 32° C). Storage above 90° F (32° C) will reduce
shelf life. Do not store above 122° F (50° C).
Availability
AdvanTech subfl oor adhesive will be available through distributors in New England (ME, NH, VT, MA, CT, RI) and NY beginning
March, 2016. Check AdvanTechSFA.com for updated availability, or sign up to be notifi ed when AdvanTech subfl oor adhesive is
available in your area.
Warranty
Visit AdvanTechSFA.com for complete details.
VOC Content
VOC ≤ 15 wt. %
VOC (California) ≤ 155 g/L
Technical Service
Detailed information including specifi cations, product literature, test reports, installation instructions, and special
applications is available through Huber Engineered Woods.
Please visit AdvanTechSFA.com or call 800.933.9220 x 2716 to speak to a technical representative.
1. Coverage: One 24 oz. can of AdvanTech subfl oor adhesive yields approximately 400 linear feet of gel adhesive at ½” bead compared to applying a 28 oz. cartridge adhesive at 3/8” bead. Coverage will vary based on bead size and weather conditions.
2. Squeak Free Guarantee for AdvanTech subfl oor assembly at joist connection: Limitations and restrictions apply. Must use AdvanTech subfl oor panels with I-joists or trusses and deformed fasteners. Not applicable over dimensional lumber framing or
with other subfl oor panels. Will be available in New England (ME, NH, VT, MA, CT, RI) and NY beginning in March 2016. Applies only to one and two family dwellings, townhomes and structures permitted under IRC or governing residential code. See
SqueakFreeGuarantee.com for complete details. 3. Coverage: One 24 oz. can of AdvanTech subfl oor adhesive yields approximately 400 linear feet of gel adhesive at ½” bead compared to applying a 28 oz. cartridge adhesive at 3/8” bead. Coverage will
vary based on bead size and weather conditions. 4. Exceeds ASTM D3498 Standard Specifi cation for Field-Gluing Plywood to Lumber Framing for Floor Systems, dry, wet, frozen, and gap fi lling adhesion tests.
© 2015 Huber Engineered Woods LLC. AdvanTech, FLAT OUT BEST, the AdvanTech logo and design are trademarks of Huber Engineered Woods LLC. HUB 9008 REV 2/16
ADVANTECH
™
SUBFLOOR ADHESIVE - PHYSICAL PROPERTIES
ASTM D3498
Shear Strength (Dry Lumber), aged Douglas Fir: > 500 psi (req > 150)
Shear Strength (Wet Lumber), aged
Douglas Fir: > 300 psi (req > 150)
Southern Pine: > 400 psi (req > 150)
Shear Strength (Frozen Lumber), aged
Douglas Fir: > 300 psi (req > 100)
Southern Pine: > 500 psi (req > 100)
Gap Filling Shear Strength, aged > 400 psi (req > 100)
Durability - Moisture Resistance, aged > 500 psi (req > 150)
Durability - Oxidation, aged Shear Strength, Flexibility Pass
ASTM C557 / ASTM D6464 ASTM C557 ASTM D646
Shear Strength, 24 Hours 91 psi 95 psi
Shear Strength, 24 Hours 104 psi 89 psi
Shear Strength, 24 Hours 108 psi 104 psi
Tensile Strength, 24 Hours 36 psi 45 psi
Tensile Strength, 24 Hours 39 psi 34 psi
Shear Strength, Freeze/Thaw 102 psi 111 psi
Shear Strength under Static Load, 20 lb., 40 lb. Pass, Pass Pass, Pass
Wet Out, Plywood, Drywall Pass -
Aging Pass Pass
Laminating Suitability, Compatibility, Staining Pass, Pass -
Gap Filling / Bridging Pass, 42 inches Pass, 42 inches
PRODUCT DATA SHEET