UNO-3072LA Intel Atom Embedded Automation Computer with Two PCI Slot Extensions User Manual i
Copyright Notice The documentation and the software included with this product are copyrighted 2010 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
-10° C (14° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. 16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70 dB (A).
Contents Chapter 1 Overview .......................................................... 2 1.1 1.2 1.3 1.4 Introduction ....................................................................... 2 Hardware Specifications ................................................... 2 Safety Precautions ............................................................. 4 Chassis Dimensions........................................................... 5 1.5 Packing List...........................................................
Appendix A System Settings and Pin Assignments ......... 34 A.1 System I/O Address and Interrupt Assignments ...... 34 Table A.1:UNO-3072LA System I/O Port .................. 34 Table A.2:UNO-3072LA Interrupt Assignments ........ 35 A.2 Board Connectors and Jumpers....................................... 36 Figure A.1:Backplane Connector & Jumpers .............. 36 Figure A.2:Mainboard Connector & Jumpers (Front) . 36 Table A.3:Connector and Jumper Descriptions ........... 37 Table A.
CHAPTER 1 Overview This chapter provides an overview of UNO-3072LA specifications.
Chapter 1 Overview 1.1 Introduction Advantech's UNO-3072LA is an Atom-based Embedded Automation Computer with two PCI slots that provides excellent power consumption capabilities. The Gigabit LAN supports the teaming function with fault tolerance, link aggregation, and load balancing. Different from general industrial PCs, UNO-3072LA is more compact and reliable with a fanless and cableless design.
• USB Interface: External:Four USB ports, USB EHCI, Rev. 2.0 compliant Internal: One USB port, USB EHCI, Rev. 2.0 compliant (Optional cable wiring: 2 x USB ports, USB EHCI, Rev 2.0 compliant) • Compact Flash Slots: Two type I/II CompactFlash Slots, One internal and one external • HDD: SATA HDD extension kit for one standard 2.
• Watchdog Timer : Programmable 256 levels timer interval, from 1 to 255 sec, with Fintek F75111 • Keyboard & Mouse: Optional cable wiring PS/2 connector 1.3 Safety Precautions The following messages inform how to make each connection. In most cases, you will simply need to connect a standard cable. Note: Always disconnect the power cord from your chassis whenever you are working on it. Do not connect while the power is on. A sudden rush of power can damage sensitive electronic components.
1.4 Chassis Dimensions 177.00 238.00 139.60 Figure 1.
1.
CHAPTER 2 Hardware Functionality This chapter shows how to setup the UNO-3072LA hardware functions, including connecting peripherals, and setting switches and indicators.
Chapter 2 Hardware Functionality 2.1 Introduction 177.00 The two figures below show the connectors on UNO-3072LA, and following sections give you detailed information about function of each peripheral. 139.60 Figure 2.
2.2 RS-232/422/485 Interface (COM1~COM2) The UNO-3072LA offers two industrial RS-232/422/485 serial communication interface ports: COM1 and COM2. Please refer to Appendix A.5 for their pin assignments. The default setting of COM1 and COM2 are RS-422/485. (Please refer to section 2.2.4 for how to determine RS-232 or RS-422/485) 2.2.
Jumper setting for RS-422/485 interface: (Default setting). Figure 2.2: RS-422/485 Jumper Setting Jumper setting for RS-232 interface: Figure 2.
2.2.5 Terminal Resistor Setup for RS-422/485 The onboard termination resistor (120 Ohm) for COM1/COM2 can be used for long distance transmission or device matching (Default Open). Each terminal resistor responds to different channels for RS-422/485. Usually, these resistors are needed for both ends of the communication wires and the value of the resistors should match the characteristic impedance of the wires used. Table 2.1: Terminal Resistor Settings COM Port Switch No.
2.2.6 RS-485 Auto Flow/RS-422 Master/Slave Selection UNO-3072LA support "Auto Flow Control" mode of RS-485 in default without any setting or jumper required. In RS-485, the driver automatically senses the direction of the data flow and switches the direction of transmission. Then no handshaking is necessary. UNO-3072LA can also allow user to adjust "Master/Slave" mode of RS422 by changing setting in BIOS for each RS-422/485 port COM1 & COM2. 1.
2.3 Optional RS-232 Interfaces (COM3~COM4) UNO-3072LA offers two optional RS-232 serial communication interfaces: COM3 and COM4. Please refer to Appendix A.4 for their pin assignments. The default of these two COM ports is "Disabled". In order to use these two COM ports, follow these steps: 1. Take the DB-9 RS-232 cable (with brackets) from accessory box. 2. Connect the end of the cable on CN17 and CN18 of the main board.
3. Boot up or reset the system, press Del to enter into BIOS 4. Select Integrated Peripherals →Super I/O device → Onboard Serial Port 1 and Onboard Serial Port 2, 5. Change the IRQ and IO address from Disablde to the above setting. 6. Press F10 or Back to "Save and Exit Setup" to finish setup change. 7. Fasten the COM port bracket on the UNO-3072LA system .
2.4 LAN: Ethernet Connector The UNO-3072LA is equipped with a Realtek RTL8139C Ethernet LAN controller that is fully compliant with IEEE 802.3u 10/100Base-T CSMA/ CD standards. The Ethernet port provides a standard RJ-45 jack on board, and LED indicators on the front side to show its Link (Green LED) and Active (Yellow LED) status. 2.5 Power Inputs UNO-3072LA comes with a Phoenix connector that carries 9~36 VDC external power input, and features reversed wiring protection.
Figure 2.5: Programmable LED In order to use programmable LED, user needs to change BIOS setting to switch the LED for COM port Tx & Rx to programmable LED function. Please follow the steps below: 1. Boot up or reset the system, press Del to enter into BIOS 2. Select Integrated Peripherals →Onboard Device → LED Select, Default setting is "Comport TX-RX", change the setting to "Programmable LED". 3. Press F10 or Back to "Save and Exit Setup" to finish setup change. Table 2.
2.6 USB Connector The USB connector is used for connecting any device that conforms to the USB interface. Many recent digital devices conform to this standard. The USB interface supports Plug and Play, which enables you to connect or disconnect a device whenever you want, without turning off the computer. The UNO-3072LA provides four connectors of USB interfaces. The USB interface complies with USB UHCI, Rev. 2.0 compliant. The USB interface can be disabled in the system BIOS setup.
Note: 1. UNO-3072LA also support 16:9 widescreen. 2. While using Microsoft Windows, if plug-n-play didn't work properly and cause no image on the monitor, please try hot key "CTRL+ALT+F1" for VGA output and "CTRL+ALT+F4" for DVI in order to manually switch video output. 2.7.
Dual Display: DVI-I + VGA (DVI through converter), can be clone mode or extend mode (independent display) Note: Be sure to check the resolution that monitor support first and only use the resolution support by monitor. 2.8 Reset Button Press the "Reset" button to activate the reset function.
2.9 Power Button UNO-3072LA standard power is ATX type. Please press the "Power" button to power on or power off. The power switch bottom featured "safety switch" which user need to use finger tip to continue press 4 second to shut the system down. It protect the system won't be accidently shut down. UNO-3072LA had also offers "AT power mode" available. Please close the jumper on CN5 in order to use AT mde Figure 2.6: Hardware AT mode Jumper Location 2.10 Audio UNO-3072LA supports audio Line out function.
CHAPTER 3 Initial Setup This chapter introduces how to initialize the UNO-3072LA.
Chapter 3 Initial Setup 3.1 Inserting a CompactFlash Card UNO-3072LA provides two CompactFlash slots. One slot (CF2) on the daughterboard is accessible from the top of the system, where you can insert your CompactFlash card directly. The other slot (CF1) is inside UNO-3072LA on its motherboard. You can set SW3-1 to decide which one is the master. SW3-1 on motherboard (refer to Figure A.
3.3 Installing a Hard Disk The procedure for installing a hard disk is listed below. Please follow these steps carefully. 1. Remove the power cord. 2. Unscrew the six screws from the bottom cover (as shown below) 3. Unscrew the HDD bracket from the upper cover.
4. Install the HDD in HDD bracket and secure with the four screws. Please refer to pictures below. Please mind the direction of the SATA hard drive connector like below. 5. SATA HDD Installation Install HDD into HDD bracket and fix with screw 6. Connect SATA cable and SATA power cable on HDD side and motherboard side. The correct connection way is shown below.
7. Re-fasten the upper cover with the six screws.
3.4 Installing a PCI-bus Card The procedure for installing a PCI-bus card into the UNO-3072LA is listed below. Please follow these steps carefully. 1. Remove the power cord. 2. Remove the upper cover of UNO-3072LA. 3. Unscrew the screw of a PCI bracket, and remove it. 4.
5. Plug-in PCI-bus card in a PCI-slot of UNO-3072LA.
6. Screw back the upper cover with the eight screws. 7.
8. Insert the PCI Anti-Vibration support kit through the hole shown till it insert tight. Cut the overhang part and fasten screws.
3.5 Mounting UNO-3072LA There are 3 types of mounting kits for UNO-3000 series: • Panel mount • Stand mount • Wallmount Pls refer to UNO-3000 Series Accessories Manual Note: Due to thermal performance issues, Wallmount will only support specific models 3.6 Installing Power Cable UNO-3072LA provides an internal backup power source so that it can provide power for a PCI Blower, external video card that required additional power or other external devices.
3.7 BIOS Setup and System Assignments UNO-3072LA adapts Advantech’s SOM-5786 CPU module. Further information about the SOM-5786CPU module can be found in user manual of SOM-5786. You can find this manual on the driver and utility CD of UNO-3072LA in the accessory package. Please note that you can try to “LOAD BIOS DEFAULTS” from the BIOS Setup manual if the UNO-3072LA does not work properly.
3.8 Rubber Foot Installation UNO-3072LA provides Rubber Foot for two purpose: <1> Anti-Shock/ Vibration purpose and <2> protect the surface of Chassis from scratch. Please find the rubber foot in accessory box shown below. Please peel the non-stick paper and put the rubber foot on the location that has been circled in red.
APPENDIX A System Settings and Pin Assignments
Appendix A System Settings and Pin Assignments A.1 System I/O Address and Interrupt Assignments Table A.
0778 - 077B Printer Port (LPT1) 0D00 - FFFF PCI bus F800 - F80F Standard Dual Channel IDE Controller FC00 - FC1F Intel SCH Family USB Universal Host Controller - 8116 FD00 - FD1F Intel SCH Family USB Universal Host Controller - 8115 FE00 - FE1F Intel SCH Family USB Universal Host Controller - 8114 FF00 - FF07 Intel Corporation US15 Embedded Graphics 443 Watchdog timer DC000-DFFFF Battery backup resource Table A.
A.2 Board Connectors and Jumpers There are several connectors and jumpers on the UNO-3072LA board. The following sections tell you how to configure the UNO-3072LA hardware setting. Figures A.1 to A.5 show the location of the connectors and jumpers. Figure A.1: Backplane Connector & Jumpers Figure A.
Table A.
Table A.
A.3 RS-232 Standard Serial Port (COM3~COM4) Table A.
A.4 RS-232/422/485 Serial Port (COM1~COM2) Table A.6: RS-232/422/485 Serial Port Pin Assigns Pin RS-232 RS-422 RS-485 1 DCD Tx- DATA- 2 RxD Tx+ DATA+ 3 TxD Rx+ NC 4 DTR Rx- NC 5 GND GND GND 6 DSR NC NC 7 RTS NC NC 8 CTS NC NC 9 RI NC NC A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.
A.6 Power Connector (PWR) Table A.8: Power connector pin assignments Pin 1 V+ (9~36VDC) 2 V- 3 Field Ground A.7 PS/2 Keyboard and Mouse Connector Table A.
A.8 USB Connector (USB1~USB4 & CN7) Table A.
A.9 VGA Display Connector DVI-I to DVI & VGA Cable or Converter Table A.
A.10 DVI-I Connector Table A.
A.11 Clear CMOS (CN3) This jumper is used to erase CMOS data and reset system BIOS information. Follow the procedures below to clear the CMOS. 1. Turn off the system. 2. Close jumper CN3 (1-2) to clear CMOS . 3, Remove jumper CN3(1-2) 3. Turn on the system. The CMOS is now cleared. 4. Turn on the system. The BIOS is reset to its default setting. Table A.
A.12 External & Internal SATA Connectors Table A.14: External SATA connector pin assignment Pin Signal name 1 2 3 4 5 6 7 GND TX+ TXGND RXRX+ GND Table A.
Table A.
UNO-3072LA User Manual 48
APPENDIX B Programming the Watchdog Timer
Appendix B Programming the Watchdog Timer To program the watchdog timer, you must write a program which writes I/ O port address 443 (hex). The output data is a value of time interval. The value range is from 01 (hex) to 3E (hex), and the related time interval is 1 sec. to 62 sec. Data Time Interval 01 1 sec. 02 2 sec. 03 3 sec. 04 4 sec. .. .. .. 3E 62 sec. After data entry, your program must refresh the watchdog timer by rewriting the I/O port 443 (hex) while simultaneously setting it.
The following example shows how you might program the watchdog timer in BASIC: 10 REM Watchdog timer example program 20 OUT &H443, data REM Start and restart the watchdog 30 GOSUB 1000 REM Your application task #1, 40 OUT &H443, data REM Reset the timer 50 GOSUB 2000 REM Your application task #2, 60 OUT &H443, data REM Reset the timer 70 X=INP (&H443) REM, Disable the watchdog timer 80 END 1000 REM Subroutine #1, your application task .. .. .. 1070 RETURN 2000 REM Subroutine #2, your application task .. ..
UNO-3072LA User Manual 52
