User Manual SOM-7565 A2
Copyright The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g. There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
9. Position the power cord so that people cannot step on it. Do not place anything over the power cord. 10. All cautions and warnings on the equipment should be noted. 11. If the equipment is not used for a long time, disconnect it from the power source to avoid damage by transient overvoltage. 12. Never pour any liquid into an opening. This may cause fire or electrical shock. 13. Never open the equipment. For safety reasons, the equipment should be opened only by qualified service personnel. 14.
Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
Contents Chapter 1 General Information ............................1 1.1 1.2 1.4 Introduction ............................................................................................... 2 Specifications ............................................................................................ 2 1.2.1 Board Information ......................................................................... 2 1.2.2 System Information ....................................................................... 2 1.2.
Appendix B Programming GPIO........................... 21 B.1 GPIO Register......................................................................................... 22 Appendix C System Assignments........................ 23 C.1 System I/O Ports..................................................................................... 24 Table C.1: System I/O ports....................................................... 24 DMA Channel Assignments .............................................................
Chapter 1 1 General Information This chapter gives background information on the SOM-7565 A2 CPU Computer on Module Sections include: Introduction Specification Functional Block Diagram SOM-7565 A2 Type 10 Pin Assignment
1.1 Introduction SOM-7565 A2 is a COM-Express Mini module with pin-out Type 10 that fully complies with the PICMG (PCI Industrial Computer Manufactures Group) COM.0 R2.1 specification. The new CPU module uses an Intel Atom processor N2800/N2600 which contains Intel GFX Core GMA3600 supports full MPEG2, AVC/H.264, and VC1 HW decode/acceleration, with NM10 chipset which supports advance expansion interface like PCI Express and I/O interface like Serial ATA (SATA), USB2.0.
1.2.6 iManager 2.0 Refer to section 4.3. 1.2.7 Mechanical and Environmental Specification Dimensions: 84 x 55 mm (3.3" x 2.17") Power Type and Supply Voltage: ATX: +12V and +5VSB (standby power) AT: +12V Power Requirement: Test Condition: Win7 32-bit standard, under 12V and 5VSB input power supply.
1.3 Functional Block Diagram Block Diagram Up to 4GB Onboard Memory IMVP 7 DDR3 800/1066 Intel Atom N2600/ N2800 Single Channel 18-bit LVDS 1 HDMI/DVI/DP Port DMI HDA 8 USB 2.0 3 PCIe x1 SATAII NM10 Onboard Flash Giga LAN 82574L 1 PCIe x1 Ethernet Connector Row A,B 1 SATA II LPC BUS WDT / GPIO / I2C iManager Serial Port/ FAN SMBus SPI Bus SPI BIOS Figure 1.1 Functional Block Diagram 1.
SATA0_TX- B17 SATA1_TX- (Optional) A18 SUS_S4# B18 SUS_STAT# A19 SATA0_RX+ B19 SATA1_RX+ (Optional) SATA0_RX- B20 SATA1_RX- (Optional) A21 GND (FIXED) B21 GND (FIXED) A22 RSVD B22 RSVD A23 RSVD B23 RSVD A24 SUS_S5# B24 PWR_OK A25 RSVD B25 RSVD A26 RSVD B26 RSVD A27 BATLOW# B27 WDT A28 SATA_ACT# B28 N/A A29 HDA_SYNC B29 HDA_SDIN1 A30 HDA_RST# B30 HDA_SDIN0 A31 GND (FIXED) B31 GND (FIXED) A32 HDA_BITCLK B32 SPKR A33 HDA_SDOUT B33 I2C_CK A34 BI
A65 PCIE_TX1- B65 PCIE_RX1- A66 GND B66 WAKE0# A67 GPI2 B67 WAKE1# A68 PCIE_TX0+ B68 PCIE_RX0+ A69 PCIE_TX0- B69 PCIE_RX0- A70 GND (FIXED) B70 GND (FIXED) A71 LVDS_A0+ B71 DDI0_PAIR0+ A72 LVDS_A0- B72 DDI0_PAIR0- A73 LVDS_A1+ B73 DDI0_PAIR1+ A74 LVDS_A1- B74 DDI0_PAIR1- A75 LVDS_A2+ B75 DDI0_PAIR2+ A76 LVDS_A2- B76 DDI0_PAIR2- A77 LVDS_VDD_EN B77 N/A A78 LVDS_A3+ B78 N/A A79 LVDS_A3- B79 LVDS_BKLT_EN A80 GND (FIXED) B80 GND (FIXED) A81 LVDS_A_
Chapter 2 2 Mechanical Information This chapter gives mechanical information on the SOM-7565 A2 CPU Computer on Module Sections include: Board Information Mechanical Drawing
2.1 Board Information The figures below indicate the main chips on SOM-7565 A2 Computer-on-Module. Please aware of these positions when designing the customer’s own carrier board to avoid mechanical and thermal problems. Intel Atom N2600 or N2800 DDR3 Memory Intel NM10 Chipset Figure 2.
Onboard SSD Figure 2.2 Board chips identify - Back 2.2 Mechanical Drawing For more detail about 2D/3D models, please find on Advantech COM support service website http://com.advantech.com. Figure 2.
Figure 2.
Chapter 3 BIOS Sections include: Entering Setup Hot/Operation key Exit BIOS Setup Utility 3
AMI BIOS has been integrated into many motherboards for over a decade. With the AMI BIOS Setup Utility, users can modify BIOS settings and control various system features. This chapter describes the basic navigation of the BIOS Setup Utility. Figure 3.1 BIOS Setup Utility Main Screen AMI BIOS ROM has a built-in BIOS Setup Utility that allows users to modify the basic system configuration. This information is stored in flash ROM so it retains the Setup information when the power is turned off. 3.
Chapter 3 3.2.4 + / - key Use this key to switch item option. 3.2.5 F1 key Use this key to display the help txt of this item. 3.2.6 F2 key Use this key to load previous all of item setting. BIOS 3.2.7 F3 key Use this key to load default setting all of items. 3.2.8 F4 key Use this key to save and exit BIOS Setup Utility.. 3.3 Exit BIOS Setup Utility Switch the Exit tab of BIOS Setup Utility and select "Save changes and Exit". The system would be restart or boot up continue.
SOM-7565 A2 User Manual 14
Chapter 4 4 S/W Introduction & Installation Sections include: S/W Introduction Driver Installation Advantech iManger
4.1 S/W Introduction The mission of Advantech Embedded Software Services is to “Enhance quality of life with Advantech platforms and Microsoft Windows embedded technology." We enable Windows Embedded software products on Advantech platforms to more effectively support the embedded computing community. Customers are freed from the hassle of dealing with multiple vendors (Hardware suppliers, System integrators, Embedded OS distributor) for projects.
GPIO Monitor General Purpose Input/Output is a flexible parallel interface that allows a variety of custom connections. It allows users to monitor the level of signal input or set the output status to switch on/off a device. Our API also provides Programmable GPIO, which allows developers to dynamically set the GPIO input or output status.
SOM-7565 A2 User Manual 18
Appendix A A Watchdog Timer This appendix gives you the information about the watchdog timer programming on the SOM-7565 A2 CPU System on Module Sections include: Watchdog Timer Programming
A.
Appendix B B Programming GPIO This Appendix gives the illustration of the General Purpose Input and Output pin setting.
B.
Appendix C C System Assignments This appendix gives you the information about the system resource allocation on the SOM-7565 A2 CPU System on Module.
C.1 System I/O Ports Table C.1: System I/O ports Addr.
0A00 - 0A0F Motherboard resources 0A79 - 0A79 ISAPNP Read Data Port 0D00 - FFFF PCI bus D080 - D087 Intel(R) Graphic Media Accelerator 3150 D400 - D41F Intel 82567V-3 Gigabit Network Connection D480 - D49F Standard Universal PCI to USB Host Controller D800 - D81F Intel ICH8 Family USB Universal Host Controller - 2832 D880 - D89F Intel ICH8 Family USB Universal Host Controller - 2831 DC00 - DC1F Intel ICH8 Family USB Universal Host Controller - 2830 E080 - E08F Intel ICH8M 3 port Serial AT
Table C.
FED20000 - FED3FFFF Motherboard resources FED40000 - FED8FFFF Motherboard resources FED90000 - FED93FFF System board FED90000 - FFFFFFFF System board FEE00000 - FEE00FFF Motherboard resources FFB00000 - FFBFFFFF Intel 82802 Firmware Hub Device FFC00000 - FFEFFFFF Motherboard resources FFF00000 - FFFFFFFF Intel 82802 Firmware Hub Device 27 SOM-7565 A2 User Manual Appendix C System Assignments Table C.
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
