SPC-530 Rackmount Server PC User's Manual
Copyright Notice This document is copyrighted, April 2000, by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements to the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
Contents Chapter 1 General Information ................................................................... 1 1.1 Introduction ................................................................................................................. 1 1.2 Model list ................................................................................................................... 1 1.3 Specifications ............................................................................................................ 1 1.
Chapter 1 General Information 1.1 Introduction The SPC-530MB / SPC-530BP, the PC/AT-compatible computer, is designed for high-reliability applications. Not only easily installed and maintained in mission critical applications and harsh environments, it is also a high-end rackmount fault-resilient server PC. The SPC-530BP can be fitted with a 20-slot PC-bus compatible passive backplane. The SPC-530MB can be fitted with an ATX motherboard.
• Paint color: Front panel: Pantone Black 4C 2X; Chassis: Brushed finish, Ni • Operating temperature: 0 to 50o C (32 to 122o F) • Relative humidity: 20 to 90% • CE compliant Hot-swap AC-DC 400-watt ATX redundant power supply (RPS-400ATX) • Output rating: 400 watts (max.) • Input voltage: 90 to 132 VAC or 180 to 264 VAC @ 47 ~ 63 Hz, switchable • Output voltages: +5 V @ 42 A, +3.3 V @ 20 A, +12 V @ 14 A, -5 V @ 1 A, -12 V @ 1 A +5 Vsb @ 0.75 A (+5 V / +3.3 V; Total: 210 watts) • Minimum load: +5 V @ 2 A, +3.
Fault detection and alarm notification • Power failure: This operates only when you have installed the redundant power supply (RPS-400ATX). If either of the two power modules fails, the dedicated LED (PWR) changes color from green to red, and an audio alarm also sounds. The dedicated LED remains red for the failed power module until it is fixed. • Fan failure: If any of the three cooling fans fails, the dedicated LED changes color from green to red, and an audio alarm also sounds.
1.
Chapter 2 System Setup The SPC-530 series is an ATX-compatible computer designed for industrial applications. This rugged chassis meets the EIA RS-310C 19" rackmount standard. Setting up your SPC-530 series requires only a screwdriver and a small amount of time. Before you begin, you should also gather together all of the cards you plan to install, as well as the disk drives you plan to use. WARNING: Disconnect all power from the chassis before you install the CPU cards.
2.2 Removing the handles The handles and mounting ears for the front panel can be removed as follows. Please see Figure 2.2 below: 2.2 Removing the handles 2.3 The cooling fans There are three cooling fans inside the chassis. To replace or service the fans, open the top cover as in Figure 2.1. Loosen the thumbscrews, and pull out the whole fan assembly. Please refer to Figure 2.3 below: 2.
2.4 Installing the disk drives 1. Open the top cover as in Figure 2.1. There is one independent disk drive bay on the front of the chassis. Remove the four outer screws which mount the drive bay to the chassis. Slide the drive bay toward the rear of the chassis, and lift it free of the chassis. See Figure 2.4 below. 2. Remove the front cover of the drive bay, and insert the drives into their proper locations in the drive bay. See Figure 2.5. 2.4 Removing the disk drive bay 2.
2.6 Installing the power supply unit There is one 400 W ATX redundant power supply installed at the front of the chassis. The power module can be hot-swapped for maintainence. 2.
Appendix A Backplanes (Optional) PCA-6120P4 Rev. A1: 15 ISA / 4 PCI / 1 PICMG-slot passive backplane Dimensions: 420 x 260 mm Termination resistor signals The termination resistors provide an impedance mismatch at the end of the bus, to prevent signal reflections. This mismatch has to be balanced by the capability of the CPU and optional cards to electrically drive the load imposed by the resistor.
PCA-6119P7 Rev.
PCA-6119P17 Rev.
Appendix B Exploded Diagrams SPC-530MB 12 SPC-530 User's Manual
SPC-530BP SPC-530 User's Manual 13
Appendix C Safety Instructions 1. Please read these safety instructions carefully. 2. Please keep this User's Manual for later reference. 3. Please disconnect this equipment from any AC outlet before cleaning. Do not use liquid or sprayed detergent for cleaning. Use a moist sheet or cloth. 4. For pluggable equipment, the socket-outlet must be installed near the equipment and must be easily accessible. 5. Please keep this equipment free from humidity. 6.
