TPC-1770/1780 Intel Touch Panel Computer with High Luminance 17" SXGA TFT LCD User Manual
Copyright The documentation and the software included with this product are copyrighted 2008 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
Declaration of Conformity CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. We recommend the use of shielded cables. This kind of cable is available from Advantech. Please contact your local supplier for ordering information. FCC Class A Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules.
Safety Instructions 1. Read these safety instructions carefully. 2. Keep this User's Manual for later reference. 3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not use liquid or spray detergents for cleaning. 4. For plug-in equipment, the power outlet socket must be located near the equipment and must be easily accessible. 5. Keep this equipment away from humidity. 6. Put this equipment on a reliable surface during installation.
20° C (-4° F) OR ABOVE 60° C (140° F). THIS COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED ENVIRONMENT. 16. CAUTION: DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED. REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED BY THE MANUFACTURER, DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER'S INSTRUCTIONS. The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70 dB (A).
Contents Chapter Chapter 1 General Information ....................................... 2 1.1 1.2 Introduction ....................................................................... 2 Specifications .................................................................... 2 1.3 1.4 1.5 1.6 LCD Specifications ........................................................... 4 Touchscreen Specifications............................................... 5 Power...........................................................
A.2 Watchdog Timer Programming....................................... 31 A.3 Example Programs .......................................................... 32 Table A.1:Watchdog Runtime Registers ..................... 31 Appendix B HDD Kit Assembly........................................ 44 Figure B.1:Removing the Rear HDD Cover ................ 44 Figure B.2:Removing the Top Screws ......................... 44 Figure B.3:Installing the HDD ..................................... 45 Figure B.
CHAPTER 1 2 General Information Sections include: • Introduction • Specifications • LCD Specifications • Touchscreen Specifications • Power • I/O Ports Arrangement • Panel Mounting • Dimensions & Cutout
Chapter 1 General Information 1.1 Introduction The TPC-1770/1780 TPC is state-of-the-art HMI. This 17" display operator interface is an x86-based platform with these key features: Fanless: By using a low power processor, the system does not have to rely on fans, which are unreliable, and cause dust to circulate inside the equipment. Bright Display: The bright TFT LCD display suits industrial demands for clear interfaces.
1.2.2 I/O Ports Item TPC-1770H TPC-1780H I/O port 10/100/1000 Base-T x 2, (Realtek RTK8111B) 10/100/1000 Base-T x 2, (Realtek RTK8111B) RS-232 x 3 (COM1, COM3, COM4) RS-232 x 3 (COM1, COM3, COM4) VGA x 1 VGA x 1 USB 2.0 x 4 USB 2.
1.3 LCD Specifications Display Type TFT color LCD Size (diagonal) 17” Maximum Resolution 1280 x 1024 (SXGA) Maximum colors 16.7M colors (RGB 6-bit + FRC data) Pixel Pitch (W x H) 0.264 x 0.264 mm Viewing Angle 160° (H), 160° (V); CR>=10 Luminance (cd / m2) 300 Contrast Ratio 800:1 Operating Temperature 0~50° C (Ambient) Backlight 4 CCFL Backlight Life Time 50,000 hours Note There might be several bright or dark pixels on the LCD. This comes from the production of the LCD.
1.4 Touchscreen Specifications Touchscreen Type Resistive Base Glass Construction Tempered Glass Resolution 1024 x 1024 Light Transmission 80% typical Controller USB Interface Power Rating 3.3 to 5V Durability 1 million touches 1.5 Power Input voltage: 18 ~ 32 Vdc, 5.55-3.
1.6 I/O Port Arrangement The arrangement of the I/O ports is shown in Figure 1.1. Figure 1.
1.7 Panel Mounting 1. There is a piece of adhesive waterproof gasket on the AL front bezel. Make sure the waterproof gasket is in position before installing the TPC-1770/1780 to the panel opening. 2. Install the TPC-1770/1780 to the panel opening. 3. Find out the ten clampers and ten long screws in the accessory pack. Hook those clampers to those holes around the four sides of the bezel. Insert the screws to every clamper and fasten them. These screws will then push on the mounting panel and fix the unit.
1.8 Dimensions & Cutout Weight: 8 Kg (without HDD) Dimensions: 414 x 347.5 x 93 mm (16.3" x 13.68" x 3.66") (WxHxD) Cutout: 400.8 x 334.3 mm (suggested) Figure 1.
CHAPTER 2 2 System Setup
Chapter 2 System Setup This chapter provides a brief explanation for operating the TPC-1770/ 1780. It is easy to make the TPC-1770/1780 start working with the below step-by-step. Step 1: Unpack the TPC-1770/1780 package. Please check the packing list at the beginning of this manual. Step 2: Install a CompactFlash containing Windows XP Embedded or other operating system. Figure 2.
Figure 2.3: Power Receptor Step 4: Plug the power lines to the system power receptor. Step 5: Push the power button to power on the system as the figure 2.4. Figure 2.
TPC-1770/1780 User Manual 12
3 CHAPTER 2 I/O Connectors & Setting Mode
Chapter 3 I/O Connector & Setting Mode 3.
CN1A COM3 RS-232 COM 3 CN1B COM4 RS-232 COM4 CN2A COM1 RS-232 COM1 CN2B VGA port Connector to VGA output CN3 Audio Jack Connector to Audio CN4 PS/2 KB/MS PS/2 connector for KB/MS CN5A LAN1 RTL8111B CN5B, CN5C USB1, USB2 USB port CN6A LAN2 RTL8111B CN6B, CN6C USB3, USB4 USB port CN8 USB 5 USB optional port CN9 USB 6 USB optional port CN12 IDE Connector 2.
3.1.
3.1.
CON.
JP4 LVDS PANEL Sel. 1024 * 768 24bit (Default) 1280 * 1024 48bit 800 * 600 24bit 1600*1200 48bit VGA only 3.1.
TPC-1770/1780 User Manual 20
CHAPTER 4 2 Software Configuration Sections include: • Utilities & Drivers
Chapter 4 Software Configuration A support CD-ROM for TPC-1770/1780 is available and along with the product. There are related utilities and drivers for TPC-1770/1780 included. Please install the Chipset INF driver, VGA graphics driver, LAN driver, audio driver, Advantech.com driver, Touchscreen driver and Watchdog Timer (WDT) driver sequentially. 4.1 Utilities & Drivers The following utilities and drivers are provided for TPC-1770/1780.
4.1.3 LAN Driver Path: \TPC-1770H\XP\LAN\ \TPC-1780H\XP\LAN\ \TPC-1780H\VISTA32\LAN\ \TPC-1780H\VISTA64\LAN\ Available for the OS’s below: • Microsoft Windows XP • Microsoft Vista 4.1.4 Touchscreen Driver Path: \TPC-1770H\XP\TouchScreen\ \TPC-1780H\XP\TouchScreen\ \TPC-1780H\VISTA32\TouchScreen\ \TPC-1780H\VISTA64\TouchScreen\ Available for the OS’s below: • Microsoft Windows XP • Microsoft Vista 4.1.
TPC-1770/1780 User Manual 24
CHAPTER 2 5 Windows XP Embedded Sections include: • EWF • HORM • Advantech Utilities
Chapter 5 Windows XP Embedded TPC-1770/1780 is in support of embedded windows platform. This section is to state the important features, EWF and HORN, provided in windows XP embedded. 5.1 EWF EWF stands for Enhanced Write Filter. It provides an upper filter in the storage device driver stack that redirects disk write operations to volatile (RAM) or non-volatile (disk) storage. EWF protects a volume from write access. The benefits are as the following. Write-protect one or more partitions on your system.
Enable EWF: Run OSLock, and then system reboot automatically. Open those software that customers want to directly use after system resume from hibernation. Hibernate via Advantech HORM utility: Please Click Start Menu->All Programs->Advantech->HORM HORM environment remains all along unless the following events occur: Run EWF commit command (ewfmgr c: -commit) and then reboot.
5.3.3 HORM This is to create HORM environment. Please go to Start Menu-> All Programs-> Advantech. This utility firstly dismounts all local physical volumes that are not protected by EWF. It requires users to input the volume list. Please follow the steps before running this utility to create full HORM environment. Enable Hibernation via Power Options in Control Panel Make C: partition EWF-enabled via OSLock Make sure that all volumes to be dismounted are not in use.
A APPENDIX 2 Watchdog Timer Programming
Appendix A WDT Programming A.1 Overview The TPC-1770/1780 cards’ watchdog timer can be used to monitor system software operation and take corrective action if the software fails to function after the programmed period. This section describes the operation of the watchdog timer, and how to program it. The watchdog timer is built into the super I/O controller SMSC SCH3114. It provides the following functions for user programming: • Can be enabled and disabled by user's program.
A.2 Watchdog Timer Programming The I/O port address of the watchdog timer is 2E(hex) and 2F(hex), 2E (hex) is the address port. 2F(hex) is the data port. You must first assign the address of register by writing address value into address port 2E(hex), then write/read data to/from the assigned register through data port 2F (hex). Table A.
A.3 Example Programs 1.
mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT pin ;---------------------------mov dx, bx add dx, 47h mov al, 0Ch out dx, al ;---------------------------; select WDT timeout unit ;---------------------------mov dx, bx add dx, 65h mov al, 80h out dx,
;---------------------------; select WDT timeout value ;---------------------------mov dx, bx add dx, 66h mov al, 10 out dx, al ; 10 seconds 2.
mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx mov ah, al mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT pin ;---------------------------mov dx, bx add dx, 47h mov al, 0Ch out dx, al 35 Chapter A
;---------------------------; select WDT timeout unit ;---------------------------mov dx, bx add dx, 65h mov al, 00h out dx, al ; minute ;---------------------------; select WDT timeout value ;---------------------------mov dx, bx add dx, 66h mov al, 5 out dx, al ; 5 minutes 3.
out dx, al mov dx, 2Fh mov al, 0ah out dx, al ;---------------------------; get base address ;---------------------------mov al, 60h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al 37 Chapter A
;---------------------------; select WDT configuration ;---------------------------mov dx, bx add dx, 67h in al, dx or al, 04h out dx, al ; reset upon mouse interrupt 4.
;---------------------------mov al, 60h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; select WDT configuration ;---------------------------mov dx, bx add dx, 67h in al, dx 39 Chapter A
or al, 02h out dx, al ; reset upon keyboard interrupt 5.
shl al, 8 mov al, 61h mov dx, 2Eh out dx, al mov dx, 2Fh in al, dx ; now, AX contains the base address mov bx, ax ; save base address in BX ;---------------------------; exit configuration state ;---------------------------mov dx, 2Eh mov al, 0AAh out dx, al ;---------------------------; Force timeout ;---------------------------mov dx, bx add dx, 68h in al, dx or al, 04h out dx, al ; force timeout 41 Chapter A
TPC-1770/1780 User Manual 42
B APPENDIX 2 HDD Kit Assembly
Appendix B HDD Kit Assembly Please follow the assembly procedure to install the HDD into the system. 1. Remove the rear HDD cover. Figure B.1: Removing the Rear HDD Cover 2. Deassemble the HDD kit from the system. Figure B.
3. Put the HDD into the HDD bracket and fasten the screws.. Figure B.3: Installing the HDD 4. Paste the Mylar (from assembly box) Figure B.
5. Put the HDD to the system and fasten the screws. Figure B.5: Attaching the HDD 6. Re-attach the rear cover and fasten the screws. The HDD has been installed successfully.
C APPENDIX 2 Fuse Specifications
Appendix C Fuse Specifications C.1 Fuse Specifications Rating: 250VAC, 5Amp Size: 5 x 20mm Note The fuse is set to break as the input voltage exceeds 33VDC for your protection. C.2 Fuse Replacement Step 1: Remove the fuse cover Step 2: Replace the damaged fuse with a new one Step 3: Place the fuse cover back in position Figure C.1: Fuse Replacement Warning Do NOT replace the fuse unless it is damaged. Do NOT replace the fuse with a different rating.
