UNO-1170A/AE Atom N270 Fanless, DIN-rail Mounted Embedded Automation Computer with 2 x LAN, 3 x COM, 4 x USB, Audio & PC/104+ User Manual
Copyright Notice The documentation and the software included with this product are copyrighted 2011 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd.
Product Warranty (2 years) Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for two years from the date of purchase. This warranty does not apply to any products which have been repaired or altered by persons other than repair personnel authorized by Advantech, or which have been subject to misuse, abuse, accident or improper installation.
CE This product has passed the CE test for environmental specifications when shielded cables are used for external wiring. FCC Class A This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
Packing List Before setting up the system, check that the items listed below are included. If any item is not, please contact your dealer immediately. • Software Supporting CD-ROM • 6P-6P-6P 20cm PS/2 Mouse/Keyboard Y cable (P/N: 1700060202) • Phoenix power connector (P/N: 1652003206) • DIN-rail & wall mount accessories • Key pro bracket • Bracket-keypro Assy for UNO-1170 A/AE • Spacer for PCI/104+ expansion (UNO-1170AE only) Safety Instructions 1. Read these safety instructions carefully. 2.
14. If one of the following situations arises, get the equipment checked by service personnel: a. The power cord or plug is damaged. b. Liquid has penetrated into the equipment. c. The equipment has been exposed to moisture. d. The equipment does not work well, or you cannot get it to work according to the user's manual. e. The equipment has been dropped and damaged. f. The equipment has obvious signs of breakage. 15.
Contents Chapter 1 UNO-1170A/AE Overview.............................. 2 1.1 1.2 1.3 1.4 1.5 Chapter Introduction ....................................................................... 2 Hardware Specifications ................................................... 2 Safety Precautions ............................................................. 3 UNO-1170A/AE Series..................................................... 4 Chassis Dimensions...........................................................
3.7 3.8 3.9 BIOS Setup and System Assignments ............................ 30 DIN-rail Mounting Setup ................................................ 31 Wallmounting Setup........................................................ 32 Appendix A System Settings and Pin Assignments ......... 34 A.1 A.2 Interrupt Assignments ..................................................... 34 Board Connectors and Jumpers....................................... 35 A.3 A.4 A.5 A.6 A.7 A.8 A.9 A.
CHAPTER 1 UNO-1170A/AE Overview Sections include: • Introduction • Hardware Specifications • Safety Precautions • UNO-1170A/AE Series • Chassis Dimensions
Chapter 1 UNO-1170A/AE Overview 1.1 Introduction UNO-1170A/AE is an DIN-rail mounted Embedded Automation Computer, which provides several serial communication ports and Ethernet interfaces. UNO-1170A/AE is designed with a compact size, small footprint, and help to saves space with its front accessible and DIN-rail design. With rich OS and driver support, such as Windows XP embedded, WES-2009, WES7P, WinCE 6.0, and even embedded Linux.
• Shock Protection: IEC 68002-27, CompactFlash: 50G @ Wall mount, half sine, 11ms (Optional, for UNO-1170AE: 20G @ wall mount, half sine, 11ms) • Vibration Protection: IEC 68002-64 (Random 1 Oct./min, 1hr/axis), CompactFlash: 2Grms@ 5~500Hz, (Optional, UNO-1170A/AE only) HDD: 0.5 Grms @ 5~500Hz • Power Supply Voltage: 10-36 VDC, reversed wiring protection • Power Requirement: Min. 36W (10-36VDC) (e.g +24 V @ 1.
1.4 UNO-1170A/AE Series There are four products in UNO-1170A/AE series, as listed below: UNO-1170A-A12E UNO-1170AE with Intel Atom N270 CPU and 1G DDR2 RAM UNO-1170AE-A12E UNO-1170A with Atom N270 CPU and 1G DDR2 RAM and PC/104+ expansion 1.5 Chassis Dimensions Figure 1.
Figure 1.
UNO-1170A/AE User Manual 6
CHAPTER 2 Hardware Functionality Sections include: •UNO-1170A/AE Peripherals •COM1~2: RS-232 Interfaces •COM 3: RS-232/422/485 Interfaces •LAN: Ethernet Connector •Power Connector •LED Indicators •PS/2 Keyboard and Mouse Connector •Universal Serial Bus Connectors •VGA: VGA Display Connector •RESET: Reset Button •Audio • PC/104+ Voltage Selection
Chapter 2 Hardware Functionality 2.1 UNO-1170A/AE Peripherals The following figures show the connectors on UNO-1170A and UNO1170AE. The following sections give you detailed information about function of each peripheral. Figure 2.1: UNO-1170A Front View Figure 2.
Figure 2.3: UNO-1170AE Front View Figure 2.
2.2 COM1~COM2: RS-232 Interfaces The UNO-1170A/AE offers two standard RS-232 serial communication interface port on COM1 and COM2. Please refer to A.2 for pin assignments. 2.3 COM3: RS-232/422/485 Interfaces The UNO-1170A/AE offers one RS-232/422/485 serial communication interface ports. The serial communication can be configured to either RS232, RS422/485 by using on-board jumper. Please refer to A.3 for pin assignments and Table 2.1 lists the default setting of each port. Table 2.
2.3.4 RS-232/422/485 Selection COM3 support 9-wire RS-232, RS-422 or RS-485 interfaces, and you can set corresponding jumpers to select serial ports as RS-232 or RS-422/485 interfaces shown in Table 2.2. Please note to reset the system to adapt this configuration change. The system detects RS-422 or RS-485 signals automatically in RS-422/ 485 mode. Table 2.
2.3.5 Terminal Resistor Setup for RS-422/485 SW3 The onboard termination resistor (120 Ohm) for COM3 can be used for long distance transmission or device matching. (Default Open.) Each terminal resistor responds to different channels for RS-422/485. Usually, these resistors are needed for both ends of the communication wires and the value of the resistors should match the characteristic impedance of the wires used. SW3 Pin 3,4 is reserved for on board COM port pin header use only. Table 2.
2.3.6 RS-485 Auto Flow & RS-422 Master/Slave Mode SW2 You can set the “Auto Flow Control” mode of RS-485 or “Master/Slave” mode of RS-422 by using the SW2 DIP switch for each RS-422/485 port. In RS-485, if the switch is set to “Auto”, the driver automatically senses the direction of the data flow and switches the direction of transmission. No handshaking is necessary. In RS-422, if DIP switch is set to “On,” the driver is always enabled, and always in high or low status.
2.4 IRQ and Address Setting The IRQ and I/O address range of COM3 are listed below: • COM3: IRQ10 (Independent IRQ), IRQ5 (Share IRQ) You can set “Share IRQ” or “Independent IRQ” by the first switch of SW2. Table 2.5: IRQ Setting via Switch 1 at SW2 Switch 1 at SW2 Setting 3 4 3 4 Function O N Share IRQ (default) O N Independent IRQ You can adjust the transmission rate by the second switch of SW2. Table 2.
2.5 LAN: Ethernet Connector The UNO-1170A/AE is equipped with two Realtek RTL8100CL Ethernet LAN controllers that are fully compliant with IEEE 802.3u 10/100Base-T CSMA/CD standards. The Ethernet port provides a standard RJ-45 jack onboard, and LED indicators on the front side to show its Link (Yellow LED) and Active (Green LED) status. Please refer to A.4 for its pin assignments. 2.
The USB interface supports Plug & Play, which enables you to connect or disconnect a device whenever you want without turning off the computer. The UNO-1170A/AE provides two connectors with USB interfaces, which gives complete Plug & Play and hot swapping for up to 127 external devices. The USB interface complies with USB specification version 2.0 compliant. OpenHCI, Rev. 1.0. The USB interface can be disabled in the system BIOS setup. Please refer to Appendix A.7 for its pin assignments. 2.
(BH1 is for real time clock, BH2 is for SRAM) 17
2.14 LED and Buzzer for System Diagnosis (Diag LED) In a “headless application” (an application without a monitor display), it is always difficult to know the system status. Another PC may be needed to monitor a headless device's status via RS-232 or Ethernet. In order to solve this problem, UNO-1170A/AE offers a programmable LED indicator and buzzer. They can be programmed to show a systems status by LED indicator flickering and buzzer alarm. Table 2.
Table 2.9: Programmable Buzzer Control Bit SPKS1 SPKS0 Beep on 0 0 Short beep 0 1 Normal beep 1 0 Long beep 1 1 2.15 PCI/104+ Connectors (UNO-1170AE only) UNO-1170AE supports up to two PCI/104+ cards. The cards will be installed on connector noted “CN18 and CN19”. If your PC/104+ card requires VIO voltage settings adjust the jumper on CN4 on the expansion board. Table 2.10: PC/104+ VIO Voltage Jumper Settings Voltage Jumper close position setting +5V 1-2 +3.3V 2-3 Jumper Setting for +3.
UNO-1170A/AE User Manual 20
CHAPTER 3 Initial Setup Sections include: • CompactFlash Installation • PC/104+ Card Installation (UNO1170AE) • Hard Drive Installation • Chassis Grounding • Power Connection • BIOS Setup and System Assignments
Chapter 3 Initial Setup 3.1 CompactFlash Card Installation The procedure for installing a CompactFlash card into the UNO-1170A/ AE is as follows, please follows these steps carefully. Although the outside appearance of the UNO-1170A/AE is different from the figures shown below, the procedure is the same. 1. Remove the power. 2. Unscrew six screws from UNO-1170A/AE indicated below. 3. Remove the rear cover. 4.
3.2 USB Keypro and Keypro Bracket Installation 1. Keep the side cover removed and have the USB keypro dongle ready. (Note: Only the upper internal USB connector will work.
2. Insert the USB keypro/dongle into the internal USB connector and place the keypro bracket as shown in the picture. Then, screw the keypro bracket. 3. Manually adjust the bracket to perfectly fit the USB keypro/dongle.
3.3 Chassis Grounding Please connect the chassis ground of UNO-1170A/AE with "EARTH". Figure 3.1: Chassis Grounding Connection 3.4 Power Connection Connect the UNO-1170A/AE to a 10 ~ 36 VDC power source. The power source can either be from a power adapter or an in-house power source.
3.5 PC/104+ Card Installation (UNO-1170AE) The procedure for installing a PC/104+ card into the UNO-1170AE is shown as following step. 1. Remove the power. 2. Unscrew four screws from UNO-1170AE indicated below.
3. Find 2 metal spacer from accessory bag, and screw tight on the location indicated arrow in the below picture. (Note: There were spacers soldered on the daughter board already). Normally you will also get some hexagon spacer from your PC/104+ card packing. Use and screw those spacers on the location indicated black shown in below picture. 4. Please refer to section 2.12 for PC/104+ card voltage setting before install the PC/104+ card. 5. Stack the PC/104+ card and related cables.
6. Screw the side cover and the six screws. Now you are done with the PC/104+ card installation. Note: You can use two PC/104+ cards at the same time while you don't use a hard drive. Using a hard drive will limit the number of PC/104+ you use to one Notes: • When use PC/104+ card, please note the system does not support S3, S4 sleep mode and DMA mode. • Maximum number of modules supported of PC/104+ cards are 2. • The expansion board support up to 4 ID selects for PC/104+.
3.6 Hard Drive installation The procedure for installing a hard drive into the UNO-1170A/AE is shown as following step. 1. Remove the power. 2. Unscrew four screws from UNO-1170A/AE indicated below. 3. Remove the side cover. Please refer to Section 3.1 & 3.2 for the instruction to open the cover. 4. Connect the SATA cable and SATA power cable. Make sure the cable will not lose. Use the screws in accessory to mount the hard drive on the hard drive bracket.
5. Connect the other end of SATA power cable on the board which the arrow indicated in below picture. 6. Screw the side cover and the four screws. 7. For user who tried to plug other SATA device, please note the UNO-1170A/AE SATA power connector doesn't support 12V power. Note: There are switch setting about SATA hard drive below, please refer to the section A.9 for detail. The hard drive might not work correctly if the switch setting is incorrect 3.
3.8 DIN-rail Mounting Setup Please follow the below steps to mount the UNO-1170A/AE on the DINRail. 1. Screw the provided DIN-Rail Kit on the rear side of UNO-1170A/ AE as the diagram shown below. 2. Hang the UNO-1170A/AE to the DIN-Rail with angle of inclination about 30 degree. 3. Let UNO-1170A/AE down straight to slide over the Rail smoothly. Note: To get the UNO-1170A/AE down from the Rail, push the device top to down then pull the bottom of the device to let it off the Rail smoothly.
3.9 Wallmounting Setup Please follow the below steps to mount the UNO-1170A/AE on the wall. 1. Screw the provided Wall Mounting Kit on the rear side of UNO1170A/AE as the diagram shown below. 2. Mount the device on the wall by the 2 pairs hooking hole provided by the Wallmounting Kit.
APPENDIX A System Settings and Pin Assignments •Board Connectors and Jumpers •RS-232 Serial Port (COM1~2) •RS-232/422/485 Serial Port (COM3) •Ethernet RJ-45 Connector •Power Screw Terminal •PS/2 Keyboard and Mouse Connector •USB Connector •VGA Display Connector •CompactFlash Master/Slave Jumper Setting •SATA DATA Connector
Appendix A System Settings and Pin Assignments A.1 Interrupt Assignments Table A.1: UNO-1170A/AE Interrupt Table Interrupt No.
A.2 Board Connectors and Jumpers There are connectors and jumpers on the UNO-1170A/AE board. The following sections tell you how to configure the UNO-1170A/AE hardware setting. Figure A-1 and figure A-2 show the locations of UNO-1170A/AE connectors and jumpers. Figure A.1: Connector & Jumper Locations (Top) Table A.
CN9 COM1 RS-232 serial port / COM2 RS-232 serial port CN12 COM2 RS-232/422/485 selection CN13 Ethernet port 1 / Ethernet port 2 CN14 Audio line in / Audio line out CN15 Internal CompactFlash card slot CN16 SATA connector (power) CN18/CN19 Board to Board connector, PC/104+ SW1 Reset switch SW2 RS-485 auto-flow and RS-422 Master/Slave mode for OM3 Terminal resistor for COM3 SW3 Figure A.2: Connector & Jumpers (UNO-1170AE) Table A.
A.3 RS-232 Serial Port (COM1~COM2) Table A.
A.4 RS-232/422/485 Serial Port (COM3) Table A.5: RS-232/422/485 Serial Ports Pin RS-232 RS-422 RS-485 1 2 3 4 5 6 7 8 9 DCD RxD TxD DTR GND DSR RTS CTS RI TxTx+ Rx+ RxGND NC NC NC NC DATADATA+ NC NC GND NC NC NC NC A.5 Ethernet RJ-45 Connector (LAN1~LAN2) Table A.
A.6 Power Screw Terminal (CN3) Table A.7: Phoenix Power Connector Pin Assigns Pin Signal Name 1 VIN ( 10 ~ 36 VDC ) 2 GND 3 Field Ground A.7 PS/2 Keyboard and Mouse Connector (CN8) Table A.8: 6 5 3 4 2 1 Table A.
A.8 USB Connector (CN4) Table A.10: USB Connector Pin Assignments Pin Signal Name Cable Color 1 VCC Red 2 DATA- White 3 DATA+ Green 4 GND Black A.9 VGA Display Connector (CN6) Table A.
A.10 SATA Data Connector Table A.
UNO-1170A/AE User Manual 42
Appendix B Programming the Watchdog Timer Advantech [W83627] WDT
Appendix B Programming the Watchdog Timer Below are samples of code for controlling the Watchdog Timer function.
