User Manual WISE-221X IoT Wireless Sensor Node
Copyright The documentation and the software included with this product are copyrighted 2019 by Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make improvements in the products described in this manual at any time without notice. No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means without the prior written permission of Advantech Co., Ltd. Information provided in this manual is intended to be accurate and reliable.
Declaration of Conformity CE This product has passed the CE test for environmental specifications. Test conditions for passing included the equipment being operated within an industrial enclosure. In order to protect the product from being damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant industrial enclosure products.
Warnings, Cautions and Notes Warning! Warnings indicate conditions, which if not observed, can cause personal injury! Caution! Cautions are included to help you avoid damaging hardware or losing data. e.g.There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer's instructions.
Note! Antenna for NA series should be ordered respectively based on the required frequency range. 1750008836-01 863-870MHz Dipole Antenna for WISE-4210/ 2210/2211 1750008837-01 902-928MHz Dipole Antenna for WISE-4210/ 2210/2211 Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Read these safety instructions carefully. Keep this User Manual for later reference. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.
DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims all responsibility for the accuracy of any statements contained herein.
Safety Precaution - Static Electricity Follow these simple precautions to protect yourself from harm and the products from damage. To avoid electrical shock, always disconnect the power from your PC chassis before you work on it. Don't touch any components on the CPU card or other cards while the PC is on. Disconnect power before making any configuration changes. The sudden rush of power as you connect a jumper or install a card may damage sensitive electronic components.
WISE-221X User Manual viii
Contents Chapter 1 Product Overview ................................1 1.1 1.2 1.3 Series Family and Specifications .............................................................. 2 Features .................................................................................................... 2 System Architecture .................................................................................. 2 Figure 1.1 System Architecture ...................................................
Chapter 4 System Configuration....................... 19 4.1 Connection.............................................................................................. 20 Figure 4.1 Connection WISE-221X and WISE-4210-AP ........... 20 Configuring WISE-4210-AP with Browser............................................... 21 4.2.1 System Requirements ................................................................ 21 4.2.2 Factory Default Settings .............................................................
Chapter 1 Product Overview 1
1.1 Series Family and Specifications WISE-221X series support frequency band as below. Function Model Description Wireless Sensor Node WISE-2210 LPWAN Wireless Self-powered CT Node Wireless Sensor Node WISE-2211 LPWAN Wireless Self-powered Sensor Node 1.2 Features WISE-221X Self-powered sensor node: No power and communication wiring Measure and transmit power current every minutes Less interference and better penetration through concrete and steel, comparedwith 2.4GHz spectrum Max.
Chapter 1 1.4 Mechanical Design and Dimensions Figure 1.2 WISE-221X Dimension Front and Side Note! User need to install antenna when you use WISE-2210/2211 3 WISE-221X User Manual Product Overview Figure 1.
1.5 LED Figure 1.3 LED of USB and COM LED COM (RF Tx) USB Colour Green Green Behaviour Description On Flash when data transmission: Transmit data to AP Always on: In bootloader mode off Idle On USB connector plug in off USB connector plug out 1.6 Reset button Figure 1.
Chapter 2 2 Product Specification
2.1 Wireless Interface IEEE Standard: IEEE 802.15.4g Operating Frequency: – NA923: 923MHz (920.8~924.4), BW:400KHz – EU868: 868MHz (865.2~868.8), BW:400KHz Data Rate: 625bps / 2.5k bps / 5k bps / 50k bps Antenna Gain – 902~928MHz: 1.48 dBi – 863~870MHz: 2.02 dBi Transmit Power: This module is up to +12dBm, but real application need to follow local regulation (e.g. FCC, 0 dBm at 625 /2.
Note! Equipment will operate below 30% humidity. However, static electricityproblems occur much more frequently at lower humidity levels. Make sure you take adequate precautions when you touch the equipment. Consider using ground straps, anti-static floor coverings, etc. if you use the equipment in low humidity environments. 2.3 Power 2.3.1 WISE-2210 1.
2.3.2 WISE-2211 1. Input power requirements: WISE-2211 is a self-powered sensor node, power source is obtained from AI(Analog input) which connected 4~20mA sensor transmitter. In other words, WISE-2211 measures data and gets power current from connected sensor transmitter. 2. Charging time Data rate TX power Data Transmission Time period 50Kbps 12 dBm 1s 5 dBm 5s 12 dBm 10s 5 dBm 5s 12 dBm 10s 12 dBm 30 s 2.
Chapter 2 2.6 I/O Specifications Note! WISE-221X modules can operate below 30% humidity. However, environments with low relative humidity are prone to problems with electrostatic discharge. Therefore, you should ensure that you take adequate precautions by using ground straps, anti-static floor coverings, or similar equipment whenever you handle this equipment, especially in lowhumidity environments. Note! User can order Advantech’s accessory: CT(Current Transformer), please see chapter 2.11.
2.8 Pin Assignment Figure 2.3 WISE-221X Pin Assignment 2.9 Application Wiring WISE-2210 AI Input current: Alternating Current (0~100 mA) Figure 2.
Chapter 2 2.10 Block Diagram Figure 2.6 WISE-2210/2211 Block Diagram 2.11 Accessory: CT(Current Transformer) User can order Advantech accessory, CT(Current Transformer) as below: P/N Power Current Hole sizing Range (Primary (Primary) Accuracy Operating Temperature 96PD-CT241-60A 3~60A Class 0.5 -20~65°C 10.0+/-0.2mm 96PD-CT248-100A 5~100A 15.7+/-0.3mm Class 0.5 -40~65°C 96PD-CT24F-200A 10~200A 20.5+/-0.3mm Class 0.5 -40~85°C 96PD-CT24C-300A 15~300A 35.7+/-0.3mm Class 0.
WISE-221X User Manual 12
Chapter 3 3 Mechanical and Hardware Installation
3.1 Interface Introduction Figure 3.
Applicable installation methods are briefly described in the following sections. 3.2.1 Poll Mount Use a screwdriver to fasten WISE-221X and mount kit. And then Use cable tie to fasten mount kit and pole. Mechanical and Hardware Installation Figure 3.2 Pole Mounting (front) Figure 3.3 Pole Mounting (back) 15 Chapter 3 3.
3.2.2 Wall Mounting WISE-221X can be fixed to a wall with mounting kit. Use a screwdriver to fasten the mounting adapter to your module, and use the end brackets included in the package in order to keep it from sliding. Figure 3.4 Wall Mounting Install Figure 3.
WISE-221X can be fixed to a cabinet with mounting rails. Use a screwdriver to fasten the DIN rail adapter to your module, and use the end brackets included in the package in order to keep it from sliding. Note! DIN-Rail Mounting adapter for WISE-221X is available for ordered: 1970000000T000 DIN-Rail Mounting kit Mechanical and Hardware Installation Figure 3.6 DIN Mounting Install Figure 3.7 DIN Mounting Install (Front) 17 Chapter 3 3.2.
Figure 3.8 DIN Mounting Install (Back) 3.3 Power Supply Wiring WISE-221X is a self-powered sensor node, power source is obtained from AI(Analog input) channels.
Chapter 4 4 System Configuration
4.1 Connection 1. 2. Connect WISE-221X to your computer via a micro-B USB port. The USB driver is required for creating a virtual COM port of a computer. Please refer to following link to get the latest USB driver: CP210x USB to UART Bridge VCP Drivers (https://www.silabs.com/products/development-tools/software/usb-to-uartbridge-vcp-drivers) Connect WISE-4210-AP to your computer via the RJ-45 LAN port, and configure the IP address of your computer as same IP domain as default IP address of module:10.0.0.
4.2.1 System Requirements Mobile Browser Chrome Android Safari Configuration Y Y Y File Upload N N N Data Log Chart Y Y Y Data Log Export N N N For PC platforms, the minimum requirements of web browsers are as below: Internet Explorer (version 11) Google Chrome (version 30) Mozilla Firefox (version 25) Mobile Browser Chrome Firefox IE11 IE10 Configuration Y Y Y Y File Upload Y Y Y N Data Log Chart Y Y Y Y Data Log Export Y Y N N 4.2.
4.2.3 Module Authorization Account Default Password Access Ability root 00000000 All privileges admin 00000000 All privileges except change, reset password and reset to default user 00000000 View module status only.
Step 6. Click "Connect" to access the end device. 23 WISE-221X User Manual System Configuration Step 1. Download and install WISE Studio through the following link: https://support.advantech.com/support/new_default.aspx Step 2. Execute WISE Studio Step 3. Power up WISE-4210-AP by line power. Step 4. Use a USB cable to communicate WISE-221x through a computer. Step 5. Click "Go to Configuration" while it shows "available USB-Serial" in USBSerial box.
Step 7. Once everything is all set, you are successfully into configuration page. 4.4 Connection between AP and Nodes The first step of the connection between WISE-221x devices and WISE-4210-AP is to configure the units in the same network with the same frequency range. Please go to "End Devices \ RF Status \ Configuration" to configure the RF module by following below instructions.
Step 1. The default IP address of WISE-4210-AP is 10.0.0.1, if you are not able to access WISE-4210-AP, please follow step 2 to search the IP address of WISE-4210AP. Step 2. Configure the Ethernet adapter under the same subnet as 10.0.0.1. In the following figure, the IP address of this computer is configured as 10.0.0.100. Find the Ethernet box in WISE Studio, and click "Go to Configuration". Chapter 4 4.5 Configure WISE-4210-AP System Configuration Step 3.
Step 5. Go to "Configuration \ Network" to configure LAN port parameters of WISE4210-AP. Step 6. Go to "Configuration \ RF Module" to configure the RF module RF Operation Mode: WISE-221x devices supports "Push Mode", the communication from the end node device to AP is uplink only, no downlink. Data Rate (bps): Lower data rate is helpful of extending communication range, while higher data rate can reduce the communication time which allows more data to be uploaded to AP in the same period of time.
4.7 WISE-221x IO configuration 4.7.1 Date Update Please go to "End Devices \ Date Update" to configure the data sample and update interval, user can input update interval. 27 WISE-221X User Manual System Configuration After configuring all of end devices into the same network with WISE-4210-AP, users can go to "End Devices" tab to check "End Device List". MAC Address: The unique identifier of each end devices. Modbus ID: Modbus ID is automatically assigned by WISE-4210-AP.
4.7.2 I/O Status Please go to "End Devices \ IO Status" to configure the RF module by following below instructions. Channel: WISE-2210/2211 has three channel, user can choose channel 0~2. CT Primary Current Value(A): It's input power current of CT. For instance, CT Primary Current Value is the power current of facility equipment and machine (See figure 1.1). CT Secondary Current Value(mA): It's output power current of CT. In other words, CT Secondary Current Value is the power current into WISE-2210.
Go to "Configuration \ Modbus \ Modbus ID" to check and configure the Modbus ID of each MAC address of AP and end node devices. User can use Modbus/TCP and Modbus/RTU protocol to access each end devices by WISE-4210-AP, polling data from different Modbus ID for different end node devices, or AP. Chapter 4 4.
Modbus Address Table for WISE-2210 and 2211: Address 4X Ch Description Attribute 40001 0 Read 40002 1 Read 40003 2 Read 40004 3 40005 4 40006 5 Read 40007 6 Read Read AI Value Read 40008 7 Read 40009 Average Ch 0~7 Read 40131~40132 0 Read 40133~40134 1 Read 40135~40136 2 Read 40137~40138 3 40139~40140 4 40141~40142 5 40143~40144 6 Read 40145~40146 7 Read 40147~40148 Average Ch 0~7 Read 40201 0 (The type codes of channels for average value can't be cha
Step 1. Configure the Private Server in "Configuration \ Cloud" 31 WISE-221X User Manual System Configuration Step 2. Enable the Data Logger function in "Advanced \ Data Logger \ Logger Configuration" Chapter 4 4.
4.10 Access WISE-4210 I/O Data by RESTful API /lpwan_message/slot_macID Description Retrieves the log data in system memory. URL Structure http://10.0.0.1/lpwan_message/slot_macID HTTP Method GET: According to the setting of filtering, server returns the all/partial of push data.
– Coordinated Universal Time (UTC) TIM String R – Local Date/Time according GMT time zone (ISO 8601) Ex. "1994-11-05T08:15:3005:00" corresponds to November 5, 1994, 8:15:30 am, US Eastern Standard Time. UUID UID String R Universally Unique Identifier (UUID) Max. 32 characters MAC ID MAC String R MAC address, ex, "00-D0-C9-F0-63F7" RSSI Rssi Number R The RSSI value R * The data type in array is as follows. [Number, Number, Number, Number] * The information in array is as follows.
[I/O Type Index Table] Index Recording I/O-type of the storage 0 Invalid 1 DI Logic Status 2 DI Counter value 3 DI Frequency value 4 DO Logic Status 5 DO Absolute Pulse Output value 6 DO Incremental Pulse Output Value 7 AI value 8 Historical Maximum AI value 9 Historical Minimum AI value 10 AI value after scaling 11 AI status flags 12 AI engineering value 13 Historical Maximum AI engineering value 14 Historical Minimum AI engineering value 24 DI period (counter mode) 25 DI
Chapter 4 System Configuration WISE-221X User Manual 35
www.advantech.com Please verify specifications before quoting. This guide is intended for reference purposes only. All product specifications are subject to change without notice. No part of this publication may be reproduced in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission of the publisher. All brand and product names are trademarks or registered trademarks of their respective companies. © Advantech Co., Ltd.
