Advidia A-44 & A-54 Installation Manual
Installation Manual of Network Camera Thank you for purchasing our product. If there are any questions, or requests, please do not hesitate to contact the dealer. This manual may contain inaccuracies or printing errors, and the content is subject to change without notice. The updates will be added to the new version of this manual. We will readily improve or update the products or procedures described in the manual. DISCLAIMER STATEMENT “Underwriters Laboratories Inc.
Installation Manual of Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
Installation Manual of Network Camera Notice: Make sure the power supply voltage is correct before using the camera. Do not drop the camera or subject it to physical shock. Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an extended period of time, put on the lens cap to protect the sensor from dirt.
Installation Manual of Network Camera Table of Contents CHAPTER 1 INTRODUCTION .......................................................................................................................... 1 1.1 APPLICATIONS ........................................................................................................................................ 1 1.2 PREPARATIONS ...................................................................................................................................
A-44 & A-54 Installation Manual Chapter 1 Introduction The network camera is an embedded digital surveillance product that combines the features of both traditional analog cameras and built in web server. This built-in video server provides the capability of providing real-time video stream compression, processing, video analysis and transmission simultaneously.
A-44 & A-54 Installation Manual Chapter 2 Dome Camera Installation 2.1 Dome Camera A-44, A-44IR & A-54 2.1.1 Appearance Description Camera description: Figure 2-1 Overview Table 2-1 Description No.
A-44 & A-54 Installation Manual Figure 2-2 Wiring Diagram 2.1.2 Installation Ceiling mounting: Note: If required, you can use a plier to remove the clip (one or two) on the side of the back box and then route cables through the opening to secure the cables on the ceiling. Figure 2-3 Remove the Clip Steps: 1. Use the screws to fix the mounting base to the ceiling; rotate the back box counterclockwise to secure it to the mounting base; use the lock screw to secure the dome camera.
A-44 & A-54 Installation Manual Figure 2-4 Mount the Camera 2. Loosen the set screws with the hex key (supplied) to remove the lower dome. Figure 2-5 Remove the Lower Dome 3. Connect the RCA analog video output toa monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle. Adjust the lens focus to obtain a perfect image and then tighten the lens set screw.
A-44 & A-54 Installation Manual Figure 2-6 Adjust the image 4. Reinstall the lower dome and tighten the screws. Figure 2-7 Reinstall the Lower Dome In-ceiling mounting: Steps: 1. Secure the mounting base to the in-ceiling mounting base with screws.
A-44 & A-54 Installation Manual Figure 2-8 Secure the Mounting Base 2. Push the dome camera to the in-ceiling mounting base, rotate the dome camera for 10 degrees counterclockwise and then fasten the lock screws to fix the camera. Figure 2-9 Fix the Camera 3.
A-44 & A-54 Installation Manual in-ceiling mounting base into the hole. Note: The thickness of the ceiling should be less than 30 mm. Figure 2-10 Mount the Camera 4. It is strongly recommended that you use a safety cable to secure the in-ceiling mounting base to the roof. Figure 2-11 Safety rope 5. Fasten the lock screws to secure the dome camera.
A-44 & A-54 Installation Manual Figure 2-12 Secure the Camera 6. Remove the lower dome and connect the RCA analog video output to a monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle. Adjust the lens focus to obtain a perfect image. Tighten the lens set screw. Figure 2-13 Adjust the Image 7. Install the trim plate with screws to finish the installation.
