Test Report No.
INTRODUCTION FCC Compliance Statement .......................................................................................................... i Safety Instructions ................................................................................................................................... iii General Information ............................................................................................................................... 1 Equipment Check list ......................................
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against radio frequency interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy. If not installed and used in accordance with the instructions, it may cause interference to radio communications.
INTRODUCTION SAFETY INSTRUCTIONS DOC COMPLIANCE NOTICE: This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. O Handling INTRODUCTION FCC COMPLIANCE STATEMENT Due to its fragile glass panel, this monitor must be handled with caution and not be exposed to impact or shock.
INTRODUCTION GENERAL INFORMATION O Caution Your new LCD monitor incorporates the latest state-of the art color Liquid Crystal Display (LCD) technology providing a wider viewing angle with higher contrast ratio. 1. Do not open any covers on the monitor. No user serviceable parts are inside. 2. In an emergency, disconnect the AC power plug. 3. To avoid electrical shock, disconnect the power cord from the monitor before connecting the signal cable to the computer. 4. Keep away from liquids and flame.
INTRODUCTION MONITOR FEATURES Before operating your display, please check to make sure that all of the items listed are present in your package: * Supports Analog and IBM compatible PC. Accessory Kit * Support DDC2B INTRODUCTION EQUIPMENT CHECK LIST * Supports DPMS for monitor power management * On Screen Control : Brightness Contrast H/V Position H-Size Phase Color Select Auto Reset Language OSD Adjustment Exit.
INSTALLATION Follow these steps to install the monitor CONTROL BUTTONS OSD Buttons : The OSD control keys are located on lower left of the GETTING STARTED 1. Before you connect the cables, make sure the monitor and system unit power switches are OFF. 2. Plug the 15-pin signal cable between the rear of your Monitor and system. The adapter may be required for certain Apple Macintosh computers. Tighten the two screws on the cable connector. 3.
CONTROL BUTTONS MONITOR SETTINGS USING THE OSD MENU GETTING STARTED The OSD menu is available in different languages (default setting: English). MENU MENU ( DOWN UP AUTO POWER ) You use this button to switch the OSD menu on and to select the highlighted function. 3 2 1 DOWN ( ) You use these buttons to mark the symbol for a function and can then make the settings for the selected function. Button Description : 1. 2. 3. 4. : Display On Screen Control menu. Access the control menu.
MENU DESCRIPTIONS MENU DESCRIPTIONS To set the OSD menu, perform the following steps: All possible adjustments of the monitor using the OSD menu are described in the following. Press the MENU button to activate the OSD menu. The main menu appears on the screen with icons for the setting functions. Setting the brightness of the display (BRIGHTNESS) Setting the contrast of the display (CONTRAST) ON-SCREEN CONTROLS ON-SCREEN CONTROLS Shifting the picture to the left or to the right (H.
POWER MANAGEMENT PRESET OPERATING MODES LED INDICATOR (POWER MANAGEMENT ACTIVE) The picture position and size have been set to optimum values at the factory for the operating modes listed above. Depending on the screen controller used, it may be necessary to adjust the display position and size. If you need to do so, refer to the section entitled "Changing the monitor setting" below. The power management feature is comprised of two stages : On or Out Of Range (Green), Off (Green blinking).
PIN ASSIGNMENT VGA Connector(Cable Side) REFERENCE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Red Green Blue No Connection Ground Red Ground Green Ground Blue Ground No Connection Ground Ground DDC SDA Horizontal Sync. Vertical Sync. DDC SCL VGA CONNECTOR LCD Viewing Angles POWER JACK(Monitor Side) 1 2 Ground DC+12V input Type 15” diagonal viewable screen TFT (Thin Film Transistor), Active Matrix Panel, 0.
TROUBLESHOOTING No power. TROUBLESHOOTING Connect the LCD Monitor to another computer. Flip the power switch ON. The Power LED turns on. Check the graphics card for proper sync scheme (or sync Make sure AC power cord is securely connected to a power outlet. polarities) to match the LCD Monitor’s specifications. Power on but no screen image. Make sure the video cable attached with this monitor is tightly Double (split) screen image. Make sure your graphics card is set to Non-Interlaced mode.
MEMO 16 MEMO 17
