34942G/35940G/35941G/35944G AUSERFAHRUNGGUT Gas hob Table de cuisson Gaskookplaat Piano di cottura Operating and Installation Instructions Notice dutilisation et dencastrement Gebruiksaanwijzing en Installatievoorschrift Istruzioni per luso e linstallazione GB FR NL IT
ENGLISH GB Important Safety Information You MUST read these warnings carefully before installing or using the hob. If you need assistance, contact our Customer Care Department on 08705 350 350 Installation l This hob must be installed by qualified personnel, according to the manufacturers instructions and to the relevant British Standards. l Any gas installation must be carried out by a registered CORGI installer. l Remove all packaging before using the hob.
room in which it has been installed. Ensure there is a continuous air supply, keeping air vents in good condition or installing a cooker hood with a venting hose. l l l l l When using the hob for a long period of time, the ventilation should be improved, by opening a window or increasing the extractor speed. Do not use this hob if it is in contact with water. Do not operate the hob with wet hands. Ensure the control knobs are in the OFF position when not in use.
Contents Important Safety Information ...................................................... 2 Instructions for the User .............................................................. 6 Description of the Hob .................................................................. 6 Operation .................................................................................... 7 Maintenance and Cleaning ............................................................ 8 The Hob Top ....................................
Guide to Use the instructions The following symbols will be found in the text to guide you throughout the Instructions: Safety Instructions F Step by step instructions for an operation Hints and Tips This appliance is manufactured according to the following EEC directives: 73/23 EEC - 90/683 EEC - 93/68 EEC 89/336 EEC - 90/396 EEC, current edition.
Description of the Hob (Mod. 34942 G) 1 3 2 3 4 1. Hob Top 5 2. Rapid Burner 3. Semi-rapid Burners 4. Double-crown Burner 5. Auxiliary Burner 6. Control knob for back left burner (semi-rapid) 7. Control knob for back right burner (semi-rapid) 8. Control knob for front right burner (auxiliary) 9. Control knob for central burner (double-crown) 10.
Operation HOB BURNERS To light a burner, turn the relevant control knob anticlockwise to the maximum position ( ), then push it down to ignite the burner. Upon, ignition, adjust the flame as required. If the burner does not ignite, turn the control knob to zero, and try again. When switching on the mains, after installation or a power cut, it is quite normal for the spark generator to be activated automatically.
Maintenance and Cleaning Before any maintenance or cleaning can be carried out, you must DISCONNECT the hob from the electricity supply. The hob is best cleaned whilst it is still warm, as spillage can be removed more easily than if it is left to cool. The Hob Top Regularly wipe over the hob top using a soft cloth well wrung out in warm water to which a little washing up liquid has been added.
Something Not Working? If the hob is not working correctly, please carry out the following checks before contacting your local AEG Service Force Centre. SYMPTOM n There is no spark when lighting the gas SOLUTION u u u u n The gas ring burns unevenly u u Check that the unit is plugged in and the electrical supply is switched on Check that the RCCB has not tripped (if fitted) Check the mains fuse has not blown Check the burner cap and crown have been replaced correctly, e.g. after cleaning.
Service and Spare Parts If you require spare parts or an engineer contact your local Service Force Centre by telephoning: 0870 5 929 929 Your call will be routed to your local Service Force Centre. For the address of your local Service Force Centre and further information about Service Force, please visit the website at www.serviceforce.co.uk When you contact the Service Centre, they will need the following information: 1. Your name, address and post code. 2. Your telephone number 3.
Guarantee Conditions Standard guarantee conditions We, AEG, undertake that if within 12 months of the date of the purchase this AEG appliance or any part thereof is proved to be defective by reason only of faulty workmanship or materials, we will, at our discretion repair or replace the same FREE OF CHARGE for labour, materials or carriage on condition that: · The appliance has been correctly installed and used only on the electricity or gas supply stated on the rating plate.
Instructions for the Installer Engineers technical data OVERALLDIMENSIONS Width: Depth: Height: Weight: 860 mm. 500 mm. 88 mm. 16 Kg. CUTOUTDIMENSIONS 830 mm. 470 mm. 30 mm. Width: Depth: Thickness: SUPPLYCONNECTIONS Gas: RC 1/2 inch (1/2 inch male) Rear right hand corner Electric: 230-240V 50Hz supply, 3 core flexible cable with non rewireable plug fitted with a 3 amp cartridge fuse. IGNITIONHTSPARK SparkGenerator Ispra Control's BF 50066 - 230-240V 0.
Instructions for the Installer BURNER RAPID (large) TYPEOFGAS POSITION NOMINALTHERMAL POWER kW NATURALGAS NOMINALFLOW 20 mbar VALUE= RATE m3/h 37.78 MJ/m3 Ws - 50.7 MJ/ m3 NOZZLEREFERENCE 1/100 mm NOMINALTHERMAL LPGGAS POWER kW 28-30/37 mbar NOMINALFLOW VALUE= RATE g/h 49.92 MJ/Kg NOZZLEREFERENCE 1/100 mm Burner Auxiliary Semi-rapid Rapid Double-Crown SEMI-RAPID (medium) AUXILIARY (small) DOUBLE CROWN MAX MIN MAX MIN MAX MIN MAX MIN 3.0 0.65 2.0 0.45 1.0 0.33 3.5 1.2 0.286 0.
Important safety requirements This hob must be installed in accordance with the Gas Safety (Installation and Use) Regulations (Current Edition) and the IEE Wiring Regulations (Current Edition). Detailed recommendations are contained in the following British Standards Codes Of Practice: B.S. 6172/ B.S. 5440, Par. 2 and B.S. 6891 Current Editions. The hob should not be installed in a bed sitting room with a volume of less than 20 m3.
Installation CLEARANCESREQUIRED WHENFITTINGTHEGASHOB WITHOUTACOOKERHOODABOVE CLEARANCESREQUIRED WHENFITTINGTHEGASHOB WITHACOOKERHOODABOVE 700 650 mm mm 700 mm 420 mm 420 mm 55 50 m mm m 100 100 420 mm mm 50 m 50 m m FO 2027* mm m 420 mm mm 55 50 m m FO 2028* Installation IMPORTANT This hob must be installed by qualified personnel to the relevant British Standards. Any gas installation must be carried out by a CORGI registered installer.
Installation FO 0814 FO 0264 A) End of shaft with nut B) Washer C) Elbow On the end of the shaft, which includes the G 1/2" threaded elbow, adjustment is fixed so that the washer is fitted between the components as shown in the diagram. Screw the parts together without using excessive force. Gas Connection Connection to the gas supply should be with either rigid or semi-rigid pipe, i.e. steel or copper. The connection should be suitable for connecting to RC 1/2 (1/2 BSP male thread).
Building in Cut Out Size The dimensions of the cut-out are given in the diagram. 0 50 0 47 86 0 83 0 n. i 5m 5 FO 2407 Building In Building over a cupboard or drawer If the hob is to be installed above a cupboard or drawer it will be necessary to fit a heat resistant board below the base of the hob on the underside of the work surface. It is also recommended to carry out the electrical connection to the hob as shown in diagrams 1 and 2 (see next page).
Building in 1 ON/OFF SWITCH 2 ON/OFF SWITCH FLEX OUTLET FLEX OUTLET FO 0764 FO 0763 Building over a kitchen unit with door 3 a 60 The panel fitted under the hob ("a") should be easily removable to allow easy access if technical assistance is needed. The space behind the kitchen unit ("b") can be used for connections. 20 min 30 Proper arrangements must be taken in designing the furniture unit, in order to avoid any contact with the bottom of the hob which can be heated when it is operated.
Building in Fitting the hob to the worktop Before fitting the hob into the cut out, a sealing gasket supplied with the hob must be fitted to the edge of the cut out. It is essential that no gaps are left in this seal in order to prevent spillage near the hob seeping into the cabinet below. F a Seal 1) Place the sealing gasket all around the edge of the cut out. 2) Place the hob into the cut out and secure it by means of the relevant fixing clamps and screws, as shown in the diagram.
Electrical connections Any electrical work required to install this hob should be carried out by a qualified electrician or competent person, in accordance with the current regulations. THISHOBMUSTBEEARTHED. The manufacturer declines any liability should these safety measures not be observed. This hob is designed to be connected to a 230-240V 50Hz AC electrical supply. Before switching on, make sure the electricity supply voltage is the same as that indicated on the hob rating plate.
Electrical connections Permanent Connection In the case of a permanent connection, it is necessary that you install a double pole switch between the hob and the electricity supply (mains), with a minimum gap of 3 mm. between the switch contacts and of a type suitable for the required load in compliance with the current electric regulations. The switch must not break the yellow and green earth cable at any point.
Fault Finding Blue Brown Preliminary Electrical Systems Check START Isolate appliance and carry out: A: Earth Continuity check. NO YES Blue Green Yellow Brown Carry out: D: Resistance to Earth check. Carry out: C: Polarity check. Has inlet fuse blown? NO Electricity supply should now be satisfactory. YES SOCKET (face view) PLUG(withcoverremoved) Earth Wire Green/Yellow Neutral Wire Blue ( ) E( ) FUSE Inlet wiring faulty. Rectify any fault.
Fault finding A.EARTHCONTINUITYCHECK Appliance must be electrically disconnected - meter set on ý (Ohms) x 1 scale and adjust zero if necessary. Test leads from any appliance earth point to earth pin on plug. Resistance should be less than 0.1 ý (Ohm), check all earth wires for continuity and all contacts are clean and tight. B.INSULATIONCHECK Appliance electrically disconnected, all switches ON. a) meter set on ý (Ohms) x 1 scale. Test leads from L to N in appliance terminal block.
Fault finding Ignition System / Gas Ignition Ignitor does not spark YES Check gas supply at burner NO Check plug top fuse and replace if necessary Light burner manually Check polarity and earth continuity of supply point Check by pass simmer adjusted Check earth continuity of appliance Check position of the electrode Check fitting of burners Check continuity from 'N' on the mains connector block and "O" on the ignitor unit Check continuity from the tip of each electrode to the terminals 1 to 5 o
Commissioning Commissioning When the hob has been fully installed it will be necessary to check the minimum flame setting. To do this, follow the procedure below. F 1) Turn the gas tap to the MAX position and ignite. 2) Set the gas tap to the MIN flame position then turn the control knob from MIN to MAX several times. If the flame is unstable or is extinguished follow the procedure below. Procedure: F 1) Re-ignite the burner and set to MIN. 2) Remove the control knob.
Conversion from Natural Gas to LPG It is important to note that this model is designed for use with natural gas but can be converted for use with butane or propane gas providing the correct injectors are fitted and the gas rate is adjusted to suit. Method F 1) Ensure that the gas taps are in the 'OFF' position 2) Isolate the hob from the electricity supply 3) Remove all pan supports, burner caps, rings, crowns and control knobs.
