COMPETENCE B59412-4 Built-In Electric Oven Operating Instructions
Dear Customer, Please read these user instructions carefully and keep them to refer to later. Please pass the user instructions on to any future owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning! Information that affects your personal safety. Important! Information that prevents damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the Appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . General Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control Panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Fat Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Pyrolytic cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Shelf Support Rails . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 1 Safety instructions 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Electrical safety • This appliance must be only connected by a registered electrician. • In the event of a fault or damage to the appliance: Take the fuses out or switch off.
How to avoid damage to the appliance • Do not line the oven with aluminium foil and do not place baking trays, pots, etc. on the oven floor, as the heat that builds up will damage the oven enamel. • Fruit juices dripping from the baking tray will leave stains, which you will not be able to remove. For very moist cakes, use a deep tray. • Do not put any strain on the oven door when open. • Never pour water directly into the oven when it is hot. This could cause damage to or discoloration of the enamel.
Description of the Appliance General Overview Control panel Door handle Full glass door 7
Control Panel Oven Power Indicator Oven Power Indicator Temperature / Time Display Oven Functions Temperature / Time Selection Function buttons Oven Features Top heat and heating elements Oven lighting Shelf positions Fat Filter Fan heating element Fan Bottom Heat Oven shelf runners, removable 8
Oven accessories Oven shelf For cookware, cake tins, roasts and grilled foods. Baking tray For cakes and biscuits. Roasting Pan For baking and roasting or as a pan for collecting fat. Oven Shelf Runner Triple shelf runner for ovens 2 side rails with 3 telescopic runners.
Before Using for the first time Setting and changing the time 3 The oven only operates when the time has been set. When the appliance has been connected to the electrical supply or when there has been a power cut, the function indicator Time flashes automatically. 1. To change a time that has already been set, press the Select button repeatedly until the function indicator Time flashes. 2. Using the / control knob, set the current time. After approx.
Initial cleaning 1 3 Clean the oven before using it for the first time. Important: Do not use caustic or abrasive cleaning agents! These can damage the oven surfaces. For the metal surfaces, use commercially available cleaning agents. 1. Open the oven door. The oven light is lit. 2. Remove all oven accessories, and clean them with warm water and a scouring agent. 3. Wash the oven in the same way, and wipe dry. 4. Wipe the front of the appliance with a damp cloth. 5.
Using the Oven 3 The oven is equipped with retractable buttons for “Oven functions” and “Temperature selection”. To use, press the relevant button. The button then sticks out.
Switching the oven on Turn the oven functions control knob to the desired function. The oven power indicator lights up. The temperature display shows the suggested temperature for the oven function selected. The oven starts to heat up. When the temperature set is reached, an audible signal sounds. Changing the oven temperature Use the / control knob to raise or lower the temperature. The setting changes in steps of 5 °C.
3 Heat indicator Indicates warming up When the oven function has been switched on the bars that slowly light up one after the other indicate how far the oven has heated up. Fast heat indicator When the fast heat function has been switched on the bars that flash one after the other indicate that fast heat is operating. In addition the bars next to the symbol light up. Residual heat indicator When the oven has been switched off, the bars that are still lit indicate the remaining residual heat in the oven.
Speedcook 1 3 After an oven function is selected, using the additional function Speedcook the empty oven can be pre-heated in a relatively short time. Important: Do not put the food to be cooked into the oven, until Speedcook is completed and the oven is operating using the desired function. 1. Set the desired oven function (e. g., Conventional ). If necessary, change the suggested temperature. 2. Press the Speedcook button. The bars next to the symbol light up.
Oven Functions The oven has the following functions: Oven function 16 Application Heating element/ fan Professional hot air For baking on up to three oven levels at the same time. Set the oven temperatures 20-40 °C lower than when using Conventional. Top heat, bottom heat, rear wall heating element, fan Conventional For baking and roasting on one oven level. Top heat, bottomheat Rotitherm For roasting larger joints of meat or poultry on one level.
Inserting the Combination Shelf, Baking Tray and Roasting Pan Inserting the baking tray or roasting pan Insert baking tray or or roasting pan on the telescopic runners of the selected oven level so that the two holes engage on the front retaining pins on the telescopic runners. 3 Inserting the oven shelf: Insert the oven shelf so that the feet point downwards. Insert the oven shelf on the telescopic runners of the selected oven level.
Inserting/Removing the Grease Filter Only use the grease filter when roasting to protect the rear heating elements from fat splashes. Inserting the grease filter Hold the grease filter by the grip and insert the two mounts downwards into the opening on the rear wall of theoven (fan opening). Taking out the grease filter Hold the grease filter by the grip and unhook it.
Clock Functions Temperature / Time Display Clock function indicators Selector Button Change display Cook time To set how long the oven is to be in use. End time To set when the oven is to switch off again. Countdown To set a countdown. A signal sounds after the time has elapsed. This function does not affect the functioning of the oven. Time To set, change or check the time (See also section “Before Using for the First Time”).
3 3 20 How to use the clock functions • After a clock function has been selected, the corresponding function indicator flashes for about 5 seconds. During this period, the desired times can be set or modified using the / dial. • When the desired time has been set, the function indicator continues to flash for approx. 5 seconds. After that the function indicator is then lit. The set time begins to run in the background.
Countdown 1. Press the Select button repeatedly until the function indicator Countdown flashes. 2. Using the / control knob set the desired countdown (max. 99.00minutes). The function indicator Countdown lights up. When 90% of the time set has elapsed, an audible signal sounds. When the time has elapsed, ”0.00“ and the function indicator flash. An audible signal sounds. To stop the flashing and the audible signal: Press any button.
Cook time 1. Select the oven function and temperature. 2. Press the Select button repeatedly until the function indicator Cook time flashes. 3. Using the / control knob set the desired cooking time (max. 09.59hours). The function indicator Cook time lights up and the oven comes on immediately. When the time has elapsed, ”0.00“ and the function indicator flash. An audible signal sounds for 2 minutes. The oven switches itself off.
End time 1. Select the oven function and temperature. 2. Press the Select button repeatedly until the End time function indicator flashes. 3. Using the / control knob set the desired switch-off time. The function indicator End time lights up and the oven comes on immediately. When the time has elapsed, ”0.00“ and the function indicator flash. An audible signal sounds for 2 minutes. The ovenswitches itself off. To stop the flashing and the audible signal: Turn the oven functions dial to ”0”.
3 Cook time and End time combined Cook time and End time can be used simultaneously, if the oven is to be switched on and off automatically at a later time. 1. Select the oven function and temperature. 2. Using the Cook time function, set the time that the dish needs to cook, In this example, 1 hour. 3. Using the End time function, set the time at which the dish should be ready. In this case, 14:05. The Cook time and End time function indicators light up and the temperature is shown in the display.
Other Functions Switching off the display 2 3 You can save energy by switching off the clock display. Switching off the clock display 1. Turn the / control knob to the right and hold it. 2. In addition press the Select button until the display goes out. As soon as the appliance is switched on again, the display comes on automatically. When the appliance is next switched off, the clock display goes out again. To have the clock display on permanently again, you must set the clock again.
Oven’s child safety device 3 The oven is fitted with a child safety device. As soon as the child safety device is activated, the oven cannot be switched on. For the child safety device to be activated, none of the oven functions must be currently selected. Activating the child safety device 1. Turn the / dial to the left and hold it. 2. In addition press the Select button until “SAFE” appears ”in the“ display. The child safety device is now activated. Deactivating the child safety device 1.
Oven safety cut-out 3 If not switched off after a certain time, or if the temperature is not modified, the oven switches off automatically. The last temperature set flashes in the temperature display. The oven switches off when the oven temperature is: 30 - 120°C 120 - 200°C 200 - 250°C 250 - max°C 3 after after after after 12.5 hours 8.5 hours 5.5 hours 3.0 hours Switching on after a safety cut-out Switch the oven off completely. It can then be switched on again.
Mechanical Door Lock When the appliance is delivered, the door lock is deactivated. Activate the door lock Pull the safety catch forwards until it locks in place. Open the oven door: 1. Shut the door. 2. Press the safety catch and keep it depressed. 3. Open the doors. Close the oven door Close the door without pressing the safety catch. 3 28 Deactivating the door lock Press the safety catch back into the panel. Switching off the appliance does not cancel the mechanical door lock.
Uses, Tables and Tips Baking Oven function: Professional hot air or Conventional Baking tins • For Conventional dark metal and non-stick tins are suitable. • For Professional hot air bright metal tins are also suitable. Oven levels • Baking with Conventional • With Professional hot air the same time: 1 baking tray: e.g. oven level 3 is possible on one oven level. you can bake on up to 3 baking trays at 1 cake tin: e.g. oven level 1 2 baking trays: z. g.
3 30 General Instructions • Insert the tray with the bevel at the front. • With Conventional or Professional hot air you can also bake with two tins next to one another on the oven shelf at the same time. This does not significantly increase baking time. When frozen foods are used the trays inserted may distort during cooking. This is due to the large difference in temperature between the freezing temperature and the temperature in the oven. Once the trays have cooled the distortion will disappear again.
2 How to use the Baking Tables The tables give the required temperature settings, baking times and oven shelf levels for a selection of typical dishes. • Temperatures and baking times are for guidance only, as these will depend on the consistency of pastry, dough or mixture, the amount and the type of baking tin. • We recommend using the lower temperature the first time and then if necessary, for example, if a deeper browning is required, or baking time is too long, selecting a higher temperature.
Baking table Baking on one oven level Type of baking Oven function Oven level Temperature Time °C Hr: Mins.
Type of baking Oven function Oven level Temperature Time °C Hr: Mins. Fruit flans (made with yeast dough/ sponge mixture)2) Professional hot air 3 150 0:35-0:50 Fruit flans (made with yeast dough/ sponge mixture)2) Conventional 3 170 0:35-0:50 Professional hot air 3 160-170 0:40-1:20 Yeast cakes with delicate toppings (e.
Type of baking Oven function Temperature Time °C Hr: Mins.
Baking on more than one oven level Professional hot air Type of baking Professional hot air Shelf positions from bottom 2 levels 3 levels Temperature in °C Time Hours: Mins.
Tips on Baking Baking results Possible cause Remedy The cake is not browned enough underneath Wrong oven level Place cake lower The cake sinks (becomes soggy, lumpy, streaky) Oven temperature too high Use a slightly lower setting Baking time too short Set a longer baking time Baking times cannot be reduced by setting higher temperatures Too much liquid in the mixture Use less liquid.
Table for Bakes and Gratins Shelf position Temperature °C Time Hours mins.
Frozen Ready Meals Table Food to be cooked Oven function Shelf position Temperature °C Time Frozen pizza Conventional 3 as per manufacturer’s instructions as per manufacturer’s instructions Chips1) (300-600 g) Rotitherm 3 200-220 as per manufacturer’s instructions Baguettes Conventional 3 as per manufacturer’s instructions as per manufacturer’s instructions Fruit flans Conventional 3 as per manufacturer’s instructions as per manufacturer’s instructions 1) Comments: Turn chips 2 or 3
Roasting Oven function: Conventional or Rotitherm Insert the grease filter when roasting! Roasting dishes • Any heat-resistant ovenware is suitable to use for roasting (please read the manufacturer's instructions). • Large roasting joints can be roasted directly in the roasting tray or on the oven shelf with the roasting tray placed below it. • For all lean meats, we recommend roasting these in a roasting tin with a lid. This will keep the meat more succulent.
Roasting table Type of meat Quantity Ovenfunction Shelf position Temperature °C Time Hours mins. Beef Pot roast 1-1.5 kg Conventional 1 200-250 2:00-2:30 per cm. of thickness Roast beef or fillet - rare per cm. of thickness Rotitherm 1 1902001) - medium per cm. of thickness Rotitherm 1 180-190 0:06-0:08 - well done per cm. of thickness Rotitherm 1 170-180 Shoulder, neck, ham joint 1-1.5 kg Rotitherm 1 160-180 1:30-2:00 Chop, spare rib 1-1.
Type of meat Shelf position Temperature °C Time Hours mins. Quantity Ovenfunction Poultry portions 200-250g each Rotitherm 1 200-220 0:35-0:50 Half chicken 400-500g each Rotitherm 1 190-210 0:35-0:50 Chicken, poulard 1-1.5 kg Rotitherm 1 190-210 0:45-1:15 Duck 1.5-2 kg Rotitherm 1 180-200 1:15-1:45 Goose 3.5-5 kg Rotitherm 1 160-180 2:30-3:30 2.5-3.5 kg Rotitherm 1 160-180 1:45-2:30 4-6 kg Rotitherm 1 140-160 2:30-4:00 1-1.
Grill Sizes 1 3 Oven function: Grill setting or Dual grill with maximum temperature Important: Always grill with the oven door closed. The empty oven should always be pre-heated with the grill functions for 5 minutes. • For grilling, place the shelf in the recommended shelf position. • Always insert the tray for collecting the fat into the first shelf position from the bottom. • The grilling times are guidelines. • Grilling is particularly suitable for flat pieces of meat or fish.
Defrosting Oven function: Defrost (no temperature setting) • Unwrap the food and place it on a plate on the oven shelf. • Do not cover with a plate or bowl, as these can substantially lengthen the defrosting time. • For defrosting, place the shelf in the 1st oven level from the bottom. Defrosting table Dish Defrosting Further time defrosting mins. time (mins.
Drying Oven function: Professional hot air • Use oven shelves covered with greaseproof paper or baking parchment. • You get a better result if you switch the oven off halfway through the drying time, open the door and leave the oven to cool down overnight. • After this finish drying the food to be dried.
Making Preserves Oven function: Bottom heat • For preserving, use only commercially available preserve jars of the same size. • Jars with twist-off or bayonet type lids and metal tins are not suitable. • When making preserves, the first shelf position from the bottom is the one most used. • Use the shelf for making preserves. There is enough room on this for up to six 1-litre preserving jars. • The jars should all be filled to the same level and clamped shut.
Preserves table The times and temperatures for making preserves are for guidance only. Preserve Temperature in°C Cooking time until simmering in mins. Continue to cook at 100°C in mins.
Outside of the appliance • Wipe the front of the appliance with a soft cloth and warm water and washing up liquid. • For metal fronts, use normal commercially available cleaning agents. Oven interior 1 3 Warning: For the purpose of cleaning the oven must be switched off and have cooled down. Clean the appliance after each use. In this way, residue is easier to clean off and does not have the chance to burn on. Residue that is not removed may cause changes to the surface colour when Pyroluxe is used. 1.
Pyrolytic cleaning 1 1 3 Warning: The oven gets very hot during this process. Keep small children away. Important! All removable parts including the side rails must be removed from the oven before using the pyroluxe function. If you use the oven shelf runners that are available as special accessories, these must be removed before pyrolytic cleaning. If the side rails/oven shelf runners are still in place, ‘C1’ appears in the time display.
Changing the length of the Pyroluxe 1. Proceed as described in the section Pyroluxe 2. While Cook time is flashing select the desired length of the pyroluxe using or : “2:15“or ”3:15”. Cook time flashes for approximately 5 seconds. Pyrolytic cleaning then starts. 3 If Cook time is no longer flashing, press the Select and then perform the setting procedure.
Shelf Support Rails The shelf support rails on the left and right hand sides of the oven can be removed for cleaning the side walls. Removing the shelf support rails First pull the front of the rail away from the oven wall (1) and then unhitch at the back (2). 3 Fitting the shelf support rails Important! The rounded ends of the guide rails must be pointing forwards! To re-insert, first hook the rail into place at the back (1) and then insert the front and press into place (2).
Oven Shelf Runner The shelf support rails on the left and right hand sides of the oven can be removed for cleaning the side walls. Removing the shelf support rails First pull the front of the rail away from the oven wall and then unhitch at the back. 1 Fitting the shelf support rails When inserting the rails, make sure that the retaining pins on the telescopic runners are pointing to the front.
Cleaning the Oven Shelf Runner 1 1 1 1 52 Clean oven shelf runners with hot water and washing up liquid. Important: The oven shelf runners cannot be cleaned in the dishwasher. Important: Do not use any aggressive or scouring cleaning agents, spray oven cleaners, steel soap pads or hard objects such as knives or sharp-edged scrapers. These destroy the coating. Important: On no account grease telescopic runners.
Oven Lighting 1 3 Warning: There is a danger of electric shock! Prior to changing the oven light bulb: – Switch off the oven! – Remove the fuses in the fuse box or switch off the circuit breaker. Place a cloth on the oven floor to protect the oven light and glass cover. Replacing the oven light bulb/ cleaning the glass cover 1. Remove the glass cover by turning it anti-clockwise and then clean it. 2. If necessary: Replace bulb with a 40 watt, 230 V, 300 °C heat-resistant oven light bulb. 3.
Oven door For easier cleaning of the oven interior the oven door of your appliance can be taken off its hinges. Removing the oven door from its hinges 1. Open the oven door as far as it will go. 2. Undo the clamping levers (A) on both door hinges fully. 3. Close the oven door as far as the first position (approx. 45°). 3 54 4. Take hold of the oven door with a hand on each side and pull it away from the oven at an upwards angle (Take care: It is heavy).
Hanging the oven door back on its hinges 1. From the handle side take hold of the oven door with a hand on each side and hold at an angle of approx. 45°. Position the recesses on the bottom of the oven door on the hinges on the oven. Let the door slide down as far as it will go. 2. Open the oven door as far as it will go. 3. Fold up the clamping levers (A) on both door hinges back into their original positions. 4. Close the oven door.
Oven door glass 1 The oven door is fitted with four panels of glass mounted one behind the other. The inner panels can be removed for cleaning. Important Rough handling, especially around the edges of the front panel, can cause the glass to break. Removing door glass panels 1. Open the oven door as far as it will go. 2. Undo the clamping levers (A) on both door hinges fully. 3. Close the oven door as far as the first position (approx. 45°).
4. Take hold of the door trim (B) on the upper edge of the door at both sides and press inwards to release the clip seal. Then remove the door trim by pulling it upwards. 5. Take hold of the door glass panels on their upper edge one after the other and take them out of the guide by pulling them upwards. Cleaning the door glass panels Clean the door glass panels thoroughly with a solution of water and washing up liquid. Then dry them carefully. 3 Putting the door glass panels back. 1.
2. Take hold of the door trim (B) at each side, position it on the inside edge of the door and plug the door trim (B) into the upper edge of the door. 3 58 On the open side of the door trim (B) there is a guide bar (C). This must be pushed between the outer door panel and the guide corner (D). The clip seal (E) must be snapped in.
3. Open the oven door as far as it will go. 4. Fold up the clamping levers (A) on both door hinges back into their original positions. 5. Close the oven door.
What to do if … Problem The oven does not heat up Possible cause Remedy The oven has not been switched on Switch on the oven The clock has not been set to the current time Set the clock to the current time The required settings have not been set Check the settings The ovenís safety cut-out has been triggered See Oven Safety Cut-out The house wiring fuse (in the fuse box) has tripped Check fuse If the fuses trip several times, please call a qualified electrician The oven lighting is not op- The
1 3 3 If you are unable to remedy the problem by following the above suggestions, please contact your dealer or the Customer Care Department. Warning! Repairs to the appliance are only to be carried out by qualified service engineers. Considerable danger to the user may result from improper repairs. If the appliance has been wrongly operated, the visit from the customer service technician or dealer may not take place free of charge, even during the warranty period.
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W 1 62 The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
www.electrolux.
