DD 8795 Cooker Hood Operating and Installation Instructions
Contents Safety warnings ................................................................................ 3 For the user ........................................................................................ 3 For the installer ................................................................................... 4 Description of the Appliance ........................................................... 6 Extraction version ...............................................................................
Safety warnings For the user • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • Always cover lighted elements, to prevent excess heat from damaging the appliance. In the case of oil, gas and coal fired cookers it is essential to avoid open flames. • Also, when frying, keep the deep frying pan on the cooker top/ cooker under careful control. • The hot oil in the frying pan might ignite due to overheating.
For the installer • When used as an extractor unit, the hood must be fitted with a 150mm diameter duct. • When installing the hood observe the following minimum distances from the cooking top: Electric cooking hobs 300mm. • The national Standard on fuel-burning systems specifies a maximum depression of 0.04 mbar in such rooms. • The air outlet must not be connected to chimney flues or combustion gas ducts.
as the outlet hole). • Failure to observe these basic instructions will drastically reduce the performance and increase the noise levels of the extractor hood.
Description of the Appliance • The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam. • The hood is supplied as an extractor unit and can also be used with a recirculation version by fitting a charcoal filter. Extraction version • In this version fumes are extracted to the outside via a duct connected to the coupling ring A. Fig. 1. • In order to obtain the best performance the ducting should have a diameter equal to the outlet hole. A Fig.
Control Panel • Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated. Turn the hood on a few minutes before you start cooking, you will then get an under pressure in the kitchen. The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared. • The hood operation can be controlled via the control ball or with the remote control (the remote control is a special accessory and is ordered separately).
Switching on the hood - Fig. 3 The control ball is a balancer switch. Pressing the control ball repeatedly towards the bottom, switches on the hood and you may select the motor level desired, depressing once again the hood switches off. press towards the bottom to switch on the hood. Switching on the light - Fig. 3 Press the control ball towards the top : once for submersed lighting, once again for full lighting, press again to switch off the light.
Maintenance and Care • The hood must always be disconnected from the electricity supply before beginning any maintenance work. Cleaning the hood • Clean the outside of the hood using a damp cloth and a mild detergent. • Never use corrosive, abrasive or flammable cleaning products. • Never insert pointed objects in the motor’s protective grid. • Wash the outside surfaces using a delicate detergent solution. Never use caustic detergents or abrasive brushes or powders.
Removing the metal grease filter Pull the handle downards, then extract the filter.Fig. 5. Handle Fig. 5 Hand washing Soak grease filters for about one hour in hot water with a greaseloosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry. Dishwasher Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process.
Charcoal filter • The charcoal filter should only be used if you want to use the hood in the recirculation function. • To do this you will need an original charcoal filter (available from your local Service Centre). • Cleaning/replacing the charcoal filter Unlike other charcoal filters, the LONGLIFE charcoal filter can be cleaned and reactivated. With normal use the filter should be cleaned every second month (when using the hood 2,5 hours per day,on avarage).
Warning • Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions. • The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations. Changing the light bulb • • • • Disconnect the cooker hood from the mains supply. Remove the lamp, use a screw driver as a lever. Fig. 7.
Something Not Working If your appliance fails to work properly please carry out the following checks. Symptom Solution The cooker hood will not start... Check that: The hood is connected to the electricity supply. Check that a fan speed has been selected The cooker hood is not working Check that: The fan speed is set high enough for the task. The grease filters are clean. The kitchen is adequately vented to allow the entry of fresh air.
Technical Specifications Dimensions (in cm): Height Width Depth Maximum absorbed power (W): Motor (W): Lighting (W): Length of the cable (cm): Electrical connection (V): 80 89,8 33,5 235 175 3x20 150 230 Mounting accessories included 1 allen spanner (for TORX screws).
Wall unit mounting - Fig. 8-9-10-11 • Place the three rubber strips on the back of the cooker hood. Where necessary mount the two spacers provided on the drill holes for definitive fixing. The spacers are useful when the wall which is to house the cooker hood is not perfectly vertical (for example: where it is partially covered with wall tiles). rubber strips rubber strips rubber strips definitive fixing definitive fixing spacers Fig.
• Mark the wall with a centre line, this will aid mounting procedure (1), position the template so that the mid line printed on the template matches with the centre line previously marked, the lower side of the template corresponds to the lower side of the hood once mounted (2). • Drill two holes Ø 8mm and fix the support bracket with two wall plugs and screws (3). • Remove the front panels (see paragraph “Removing the front panels”).
• Fix the sides of the 11 cooker hood by fastening the pins (10a) to the sides of the fastening screws (10b). • Block the sides 10a sliding the two tabs outwards (11). • Make electrical connection (12), but 10b leave the hood Fig. 10 disconnected from the home mains circuit. • In the case that it is decided to use the cooker hood in the mains circuit, then place one of the two flanges provided in the exit hole (13 – Extraction).
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines,vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.
