FAVORIT EXPRESS User manual Benutzerinformation Dishwasher Geschirrspüler
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information 3 Operating instructions Safety information For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. Correct use • • • • • • • • • • The appliance is designed exclusively for domestic use. Only use the appliance to clean household utensils that are applicable for dishwashers.
Product description Installation • Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary, contact the supplier. • Remove all packaging before first use. • A qualified and competent person must do the electrical installation. • A qualified and competent person must do the plumbing installation. • Do not change the specifications or modify this product. Risk of injury and damage to the appliance.
Control panel 1 2 3 4 5 6 7 8 9 10 Upper basket Water hardness dial Salt container Detergent dispenser Rinse aid dispenser Rating plate Filters Lower spray arm Upper spray arm Worktop Control panel 7 10 8 9 5
Control panel 1 2 3 4 5 6 7 8 9 10 On/off button Cancel button (RESET) Programme selection buttons Save energy button (ÖKO PLUS) Multitab button (MULTITAB) Delay start button Digital display Function buttons Indicator lights Programme indicator lights Indicator lights ÖKO PLUS Comes on when the save energy function is active. MULTITAB Comes on when you activate the multitab function. Refer to 'Multitab function'. Salt 1) Comes on when it is necessary to fill the salt container.
Use of the appliance 7 Delay start button Use the delay start button to delay the start of the washing programme with an interval between 1 and 19 hours. Refer to the chapter 'Setting and starting a washing programme'. Digital display The display shows: • the set level of the water softener. • Remaining time to the end of the programme. • Activation/deactivation of the rinse aid dispenser (only with multitab function on). • End of the washing programme. The display shows a zero.
Setting the water softener Setting the water softener The water softener removes minerals and salts from the water supply. Minerals and salts can have bad effect on the operation of the appliance. Water hardness is measured in equivalent scales: • German degrees (dH°). • French degrees (°TH). • mmol/l (millimol per litre - international unit for the hardness of water). • Clarke. Adjust the water softener to the water hardness in your area. If necessary, contact your local water authority.
Use of dishwasher salt 9 Electronic adjustment The water softener is set at the factory at level 5. 1. Switch on the appliance. 2. Make sure that the appliance is in setting mode. 3. Press and hold function buttons B and C until the programme indicator lights above function buttons A, B and C start to flash. 4. Release function buttons B and C. 5. Press function button A. – The programme indicator lights above function buttons B and C go off.
Use of rinse aid Use of rinse aid CAUTION! Only use branded rinse aid for dishwashers. Do not fill the rinse aid dispenser with other products (e.g. dishwasher cleaning agent, liquid detergent). This can cause damage to the appliance. Rinse aid makes it possible to dry the dishes without streaks and stains. Rinse aid is automatically added during the last rinsing phase. Do these steps to fill the rinse aid dispenser: 1. Press the release button (A) to open the rinse aid dispenser. 2.
Loading cutlery and dishes 11 Turn the rinse aid dial to increase or decrease the dosage. – Increase the dosage if there are water droplets or limescale on the dishes. – Decrease the dosage if there are streaks, whitish stains or bluish layers on the dishes. Loading cutlery and dishes Helpful hints and tips CAUTION! Only use the appliance for household utensils that are applicable for dishwashers. Do not use the appliance to clean objects that can absorb water (sponges, household cloths, etc.).
Loading cutlery and dishes Lower basket Put large and heavily soiled dishes and pans in the lower basket. The rows of prongs in the lower basket can be flat to load large dishes, pots, pans and bowls. Cutlery basket WARNING! Do not put long-bladed knives in a vertical position. Arrange long and sharp cutlery horizontally in the upper basket. Be careful with sharp items.
Loading cutlery and dishes Use the cutlery grids. • Put the grids on the cutlery basket. • For larger items use only one of the cutlery grids. • Put forks and spoons with the handles down. • Put knives with the handles up. • Mix spoons with other cutlery to prevent them to bond together. Upper basket The upper basket is for saucers, salad bowls, cups, glasses, pots and lids. Arrange the items to let water touch all surfaces.
Loading cutlery and dishes • For longer items fold the cup racks up. • Put glasses with long stems in the cup racks with the stems up. • For glasses with long stems, turn the glass holder to the left or to the right. • You can fold up or down the row of prongs on the left side of the upper basket to increase load flexibility. Adjustment of the height of the upper basket You can put the upper basket in two positions to increase load flexibility.
Use of detergent 1. Pull out the upper basket until it stops. 2. Hold the upper basket by the handle, lift it as far as possible and lower it vertically. The upper basket latches into the lower or the upper position. Use of detergent Only use detergents (powder, liquid or tablet) that are applicable for dishwashers. Follow the data on the packaging: • Dosage recommended by the manufacturer. • Storage recommendations. Do not use more than the correct quantity of detergent to save an environment.
Multitab function 3. If you use a washing programme with prewash phase, put more detergent in the prewash detergent compartment (B). A B 4. If you use detergent tablets, put the detergent tablet in the detergent dispenser (A). 5. Close the lid of the detergent dispenser. Press the lid until it locks into position. Different brands of detergent dissolve in different times. Some detergent tablets do not have the best cleaning results during short washing programmes.
Multitab function 17 To activate the multitab function: • Press the multitab button. The multitab indicator light comes on. To deactivate the multitab function: • Press the multitab button. The multitab indicator light goes off. Do these steps if the drying results are not satisfactory: 1. Fill the rinse aid dispenser with rinse aid. 2. Activate the rinse aid dispenser. 3. Set the rinse aid dosage to position 2.
Washing programmes Washing programmes Washing programmes Programme Degree of soil Type of load Programme description Save energy 1) AUTO 45-70°2) Any Crockery, cutlery, pots and pans Prewash selectable, impact on Main wash up to 45°C or washing programme 70°C 1 or 2 intermediate rinses Final rinse Drying INTENSIV CARE 70° Heavy soil Crockery, cutlery, pots and pans Prewash Main wash up to 70°C 1 intermediate rinse Final rinse Drying selectable, impact on washing programme 30 MIN 60°3) No
Setting and starting a washing programme Programme Duration (in minutes) 1) Energy (in kWh) 19 Water (in litres) GLASS 45° - 0,8 - 0,9 14 - 15 1 HOUR 55° - 1,0 - 1,2 11 - 12 1) The digital display shows the programme duration. The pressure and temperature of the water, the variations of power supply and the quantity of dishes can change these values. Setting and starting a washing programme Set the options before the start of a washing programme.
Setting and starting a washing programme Cancelling a washing programme 1. Press and hold the cancel button until all programme indicator lights come on. 2. Release the cancel button. At this time you can do these steps: 1. Switch off the appliance. 2. Set a new washing programme . Fill the detergent dispenser with detergent before you set a new washing programme. Setting and starting a washing programme with delay start 1. Press the on/off button. 2. Set a washing programme. 3.
Care and cleaning 21 Three minutes after the end of the programme, all indicator lights go off and the digital display shows one horizontal bar. Press one of the buttons (not the on/off button), to go back to end-of-programme mode. Removing the load • First remove items from the lower basket, then from the upper basket. • There can be water on the sides and door of the appliance. Stainless steel becomes cool more quickly than the dishes.
What to do if… 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. To unlock the filter system, turn the handle on the microfilter (B) approximately 1/4 anticlockwise. Remove the filter system. Hold the coarse filter (A) by the handle with the hole. Remove the coarse filter (A) from the microfilter (B). Remove the flat filter (C) from the bottom of the appliance. Clean the filters below running water. Put the flat filter (C) in the bottom of the appliance.
What to do if… 23 If there is a fault, first try to find a solution to the problem yourself. If you cannot find a solution to the problem yourself, contact the Service Force Centre. CAUTION! Switch off the appliance before you do the below suggested corrective actions. Fault code and malfunction Possible cause and solution • intermittent audible signal • digital display shows The dishwasher does not fill with water • The water tap is blocked or furred with limescale. Clean the water tap.
Technical data The cleaning results are not satisfactory The dishes are not clean • The selected washing programme is not applicable for the type of load and soil. • The baskets are loaded incorrectly so that water cannot reach all surfaces. • Spray arms do not turn freely because of incorrect arrangement of the load. • The filters are dirty or not correctly installed. • The quantity of detergent is too little or missing. Limescales particles on the dishes • The salt container is empty.
Installation 25 Put the appliance adjacent to a water tap and a water drain. Remove the appliance worktop to install it under a sink unit or a kitchen worktop. Make sure that the dimensions of the recess agree with the given dimensions. Do these steps to remove the appliance worktop: 1. Remove the rear screws (1). 2. Pull the worktop from the behind the appliance. 3. Lift the worktop and move it from the front slots. 4. Use the adjustable feet to adjust the level of the appliance.
Water connection Water connection Water inlet hose Connected the appliance to a hot (max. 60°) or cold water supply. If the hot water comes from alternative sources of energy that are more environmentally friendly (e.g. solar or photovoltaic panels and aeolian), use a hot water supply to decrease energy consumption. Connect the inlet hose to a water tap with an external thread of 3/4”. CAUTION! Do not use connection hoses from an old appliance.
Electrical connection 27 max 400 cm 2. Connect the water drain hose to a stand pipe with vent-hole (minimum internal diameter 4 cm). Make sure that the drain hose is not bent or max 85 cm squashed to prevent that the water drains does not drain correctly. Remove the sink plug when the appliance drains min 40 cm the water to prevent that the water goes back into the appliance. A drain hose extension must not be longer than 2 m. The internal diameter must not be smaller than the diameter of the hose.
Environment concerns and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc.
Inhalt 29 Danke, dass Sie sich für eines unserer hochqualitativen Produkte entschieden haben. Lesen Sie für eine optimale und gleichmäßige Leistung Ihres Gerätes diese Benutzerinformation bitte sorgfältig durch. Sie wird Ihnen helfen, alle Vorgänge perfekt und äußerst effizient zu steuern. Damit Sie diese Benutzerinformation bei Bedarf stets zur Hand haben, empfehlen wir Ihnen, sie an einem sicheren Ort aufzubewahren.
Sicherheitshinweise Gebrauchsanweisung Sicherheitshinweise Lesen Sie diese Bedienungsanleitung bitte sorgfältig durch, bevor Sie das Gerät anschließen und benutzen, um Gefahren zu vermeiden und einen korrekten Betrieb des Geräts zu gewährleisten. Bewahren Sie diese Bedienungsanleitung in der Nähe des Geräts auf, auch wenn Sie dieses anderswo aufstellen. Wenn Sie das Gerät verkaufen, geben Sie dem Käufer die Bedienungsanleitung mit.
Sicherheitshinweise 31 • Halten Sie das Verpackungsmaterial von Kindern fern. Andernfalls besteht Erstickungsgefahr. • Bewahren Sie alle Reinigungsmittel an einem sicheren Ort auf. Achten Sie darauf, dass Reinigungsmittel nicht in die Hände von Kindern gelangen. • Halten Sie Kinder vom geöffneten Geschirrspüler fern. Installation • Vergewissern Sie sich, dass das Gerät beim Transport nicht beschädigt wurde. Schließen Sie ein beschädigtes Gerät nicht an. Wenden Sie sich bei Bedarf an den Hersteller.
Gerätebeschreibung Gerätebeschreibung 1 2 3 4 5 6 7 8 9 10 Oberkorb Anzeige der Wasserhärtestufe Salzbehälter Behälter für Reinigungsmittel Dosiergerät für Klarspüler Typenschild Filter Unterer Sprüharm Oberer Sprüharm Arbeitsplatte
Bedienblende 33 Bedienblende 7 10 9 8 1 2 3 4 5 6 7 8 9 10 Ein/Aus-Taste Lösch-Taste (RESET) Programmwahltasten Energiesparen-Taste (ÖKO PLUS) Multitab-Taste (MULTITAB) Zeitvorwahl-Taste Digital-Display Funktionstasten Kontrolllampen Programmkontrolllampen Kontrolllampen ÖKO PLUS Leuchtet auf, wenn die Funktion Energiesparen eingeschaltet ist. MULTITAB Leuchtet auf, wenn Sie die Funktion Multitab einschalten. Siehe Abschnitt "Funktion Multitab".
Bedienblende Kontrolllampen Salz 1) Leuchtet auf, wenn der Salzbehälter aufgefüllt werden muss. Siehe Abschnitt "Verwendung von Geschirrspülsalz". Die Kontrolllampe für Salz kann nach dem Nachfüllen von Salz noch einige Stunden leuchten. Dies hat jedoch keine unerwünschte Auswirkung auf den Gerätebetrieb. Klarspüler 1) Leuchtet auf, wenn Klarspüler nachgefüllt werden muss. Näheres hierzu siehe Abschnitt "Verwendung von Klarspüler".
Vor der ersten Inbetriebnahme 35 • Zum Einstellen des Wasserenthärters. Siehe den Abschnitt 'Einstellung des Wasserenthärters. • Zum Ein-/Abschalten des Klarspüldosierers, wenn die Funktion Multitab eingeschaltet ist. Siehe den Abschnitt 'Funktion Multitab'. Einstellmodus Das Gerät muss sich für folgende Einstellungen im Einstellmodus befinden: • Zum Einstellen eines Spülprogramms. • Zum Einstellen des Wasserenthärter-Härtegrads. • Zum Ein-/Ausschalten des Klarspüldosierers.
Einstellen des Wasserenthärters Wasserhärte Einstellung des Wasserenthärters °dH °TH mmol/l Clarke-Werte Manuell Elektronisch 51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10 43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5 15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3 4 - 10 7 - 18 0,7
Gebrauch von Salz für Geschirrspüler 37 Beispiel: Digital-Display zeigt = Stufe 5 an. 6. Drücken Sie die Funktionstaste A einmal, um die Einstellung des Wasserenthärters um jeweils eine Stufe zu erhöhen. 7. Drücken Sie die Ein-/Aus-Taste, um die Einstellung zu speichern. Gebrauch von Salz für Geschirrspüler VORSICHT! Verwenden Sie ausschließlich Geschirrspülsalz. Andere Salzarten, die nicht auf Geschirrspüler ausgelegt sind, können den Wasserenthärter beschädigen.
Gebrauch von Klarspülmittel 1. Drücken Sie die Entriegelungstaste (A), um den Klarspüldosierer zu öffnen. 2. Füllen Sie den Klarspüldosierer mit Klarspüler. Der maximale Füllstand wird durch die Markierung "max".angezeigt. 3. Wischen Sie verschütteten Klarspüler mit einem saugfähigen Tuch auf, um zu große Schaumbildung beim nächsten Spülprogramm zu vermeiden. 4. Schließen Sie den Klarspülerdosierer. Einstellung des Klarspüldosierers Der Wasserenthärter ist werkseitig auf Härtestufe 4 eingestellt.
Laden von Besteck und Geschirr 39 Laden von Besteck und Geschirr Hilfreiche Hinweise und Tipps VORSICHT! Spülen Sie in diesem Gerät ausschließlich spülmaschinengeeignete Haushaltsutensilien. Spülen Sie in diesem Gerät keine Wasser absorbierenden Gegenstände (Schwämme, Geschirrtücher usw.). • Bevor Sie Geschirr und Besteck ins Gerät einordnen, gehen Sie folgendermaßen vor: – Entfernen Sie alle Essensreste und sonstigen größeren Partikel. – Weichen Sie angebrannte Reste in Pfannen, Töpfen usw. ein.
Laden von Besteck und Geschirr Unterkorb Ordnen Sie größeres und stark verschmutztes Geschirr in den Unterkorb ein. Die Stachelreihen am Unterkorb können flach umgeklappt werden, um Servierplatten, Töpfe, Pfannen und Schüsseln einzuordnen. Besteckkorb WARNUNG! Stellen Sie keine Messer mit langen Klingen in aufrechter Stellung ein. Legen Sie langes oder scharfes Besteck waagerecht in den Oberkorb. Gehen Sie vorsichtig mit scharfen Gegenständen um.
Laden von Besteck und Geschirr Verwenden Sie das Besteckgitter. • Setzen Sie die Gitter auf den Besteckkorb. • Für größere Besteckteile benutzen Sie den Besteckkorb auf einer Seite ohne Besteckgitter. • Stellen Sie Gabeln und Löffel mit den Griffen nach unten ein. • Stellen Sie Messer mit den Griffen nach oben ein. • Mischen Sie Löffel mit anderem Besteck, damit sie nicht zusammenkleben können.
Laden von Besteck und Geschirr • Klappen Sie die Tassenablagen zum Einordnen höherer Gegenstände nach oben. • Langstielige Gläser können mit dem Stiel nach oben in die Tassenablagen gestellt werden. • Klappen Sie den Glashalter für langstielige Gläser nach links oder rechts. • Die Stachelreihe auf der linken Seite des Oberkorbs kann für eine flexiblere Beladung umgeklappt werden.
Gebrauch von Spülmittel 43 Gehen Sie folgendermaßen vor, um den Oberkorb in die untere/obere Position zu bringen: 1. Ziehen Sie den Oberkorb bis zum Anschlag heraus. 2. Halten Sie den Oberkorb am Griff, heben Sie ihn bis zum Anschlag an und senken Sie ihn dann senkrecht ab. Der Oberkorb rastet in der unteren oder oberen Position ein. Gebrauch von Spülmittel Verwenden Sie ausschließlich Spülmittel (Pulver, Flüssigspülmittel oder GeschirrspülerTabs) speziell für Geschirrspüler.
Funktion "Multitab" 3. Geben Sie bei einem Spülprogramm mit Vorspülgang zusätzlich etwas Spülmittel ins Vorspülfach ( B). A B 4. Wenn Sie Geschirrspüler-Tabs verwenden, legen Sie diese in den Reinigungsmittelbehälter ( A). 5. Schließen Sie den Deckel des Spülmittelbehälters. Drücken Sie auf den Deckel, bis er einrastet. Spülmittel unterschiedlicher Marken lösen sich unterschiedlich schnell auf. Einige Geschirrspüler-Tabs erbringen bei kurzen Spülprogrammen keine optimalen Ergebnisse.
Funktion "Multitab" 45 Schalten Sie die Funktion Multitab vor dem Beginn eines Spülprogramms ein oder aus. Sie können die Funktion Multitab nicht ein- oder ausschalten, wenn das Programm angelaufen ist. Brechen Sie das Spülprogramm ab und stellen Sie das Programm dann erneut ein. Schalten Sie die Funktion Multitab wie folgt ein: • Drücken Sie die Multitab-Taste. Die Multitab-Kontrolllampe leuchtet auf. Schalten Sie die Funktion Multitab wie folgt aus: • Drücken Sie die Multitab-Taste.
Spülprogramme Spülprogramme Spülprogramme Programm Grad der Verschmutzung Spülgut Programmbeschreibung Energiesparen 1) AUTO 45-70°2) Beliebig Geschirr, Besteck, Töpfe, Pfannen Vorspülgang Hauptspülgang bis zu 45 °C oder 70 °C 1 oder 2 Zwischenklarspülgänge Klarspülgang Trocknen Wählbar, mit Auswirkung auf das Spülprogramm INTENSIV CARE 70° Stark verschmutzt Geschirr, Besteck, Töpfe, Pfannen Vorspülgang Hauptspülgang bis zu 70 °C 1 Zwischenspülgang Klarspülgang Trocknen Wählbar, mit Auswi
Auswählen und Starten eines Spülprogramms 47 Verbrauchswerte Programm AUTO 45-70° Programmdauer (in Minuten) 1) Energieverbrauch (in kWh) Wasser (in Liter) - 1,1 - 1,7 12 - 23 INTENSIV CARE 70° - 1,5 - 1,7 16 - 18 30 MIN 60° - 0,9 9 ECO 50° - 1,0 - 1,1 12 - 13 45° GLAS - 0,8 - 0,9 14 - 15 1 HOUR 55° - 1,0 - 1,2 11 - 12 1) Das Digital-Display zeigt die Programmdauer an.
Auswählen und Starten eines Spülprogramms VORSICHT! Öffnen Sie die Tür vorsichtig. Es könnte heißer Dampf austreten. Unterbrechen eines Spülprogramms Öffnen Sie die Tür. • Das Programm stoppt. Schließen Sie die Tür. • Das Programm wird ab der Stelle fortgesetzt, an der es unterbrochen wurde. Abbrechen eines Spülprogramms 1. Drücken und halten Sie die Löschtaste solange, bis alle Programm-Kontrolllampen aufleuchten. 2. Lassen Sie die Löschtaste los. Nun haben Sie folgende Möglichkeiten: 1.
Reinigung und Pflege 49 1. Schalten Sie das Gerät aus. 2. Öffnen Sie die Tür. 3. Damit das Spülgut besser trocknet, öffnen Sie die Tür einen Spaltbreit und warten Sie einige Minuten, bevor Sie das Spülgut entnehmen. Lassen Sie das Spülgut abkühlen, bevor Sie es aus dem Gerät nehmen. Heißes Geschirr ist leicht zu beschädigen. Falls die Energiesparfunktion eingestellt ist, kann es sein, dass das Geschirr nach dem Ende des Spülprogramms noch feucht ist.
Reinigung und Pflege 3. Flachfilter (C) Gehen Sie wie folgt vor, um die Filter zu reinigen: 1. Öffnen Sie die Tür. 2. Entfernen Sie den Unterkorb. A B C 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. Um das Filtersystem zu entriegeln, drehen Sie den Griff des Mikrofilters (B) etwa 1/4 Drehung gegen den Uhrzeigersinn. Nehmen Sie das Filtersystem heraus. Fassen Sie den Grobfilter (A) am Handgriff. Nehmen Sie den Grobfilter (A) aus dem Mikrofilter (B).
Was tun, wenn … 51 Reinigung der Außenseiten Reinigen Sie die Außenseiten und die Bedienblende des Geräts mit einem weichen feuchten Tuch. Verwenden Sie dazu ausschließlich Neutralreiniger. Verwenden Sie keine Scheuermittel, Scheuerschwämmchen oder Lösungsmittel (Azeton, Trichloräthylen usw.) Frostschutzmaßnahmen VORSICHT! Stellen Sie das Gerät nicht an einer Stelle auf, an der die Temperatur unter 0 °C absinken kann. Der Hersteller haftet nicht für Frostschäden.
Was tun, wenn … Fehlercode und Störung Das Programm startet nicht Mögliche Ursachen und Abhilfe • Die Tür des Geräts ist nicht geschlossen. Schließen Sie die Tür. • Der Netzstecker ist nicht eingesteckt. Stecken Sie den Netzstecker in die Netzsteckdose. • Die Sicherung der Hausinstallation ist durchgebrannt. Tauschen Sie die Sicherung aus. • Die Zeitvorwahl ist eingestellt. Brechen Sie die Zeitvorwahl ab, damit das Programm sofort gestartet wird.
Technische Daten 53 Technische Daten Abmessungen Breite in cm 59,6 Höhe in cm 85 Tiefe in cm 62,5 Elektrischer Anschluss - AnDie Daten der elektrischen Anschlusswerte befinden sich auf dem schlussspannung - Gesamtleis- Typenschild am Innenrand der Geschirrspülertür.
Wasseranschluss Gehen Sie wie folgt vor, um die Arbeitsplatte des Gerätes zu entfernen: 1. Lösen Sie die hinteren Schrauben (1). 2. Ziehen Sie die Arbeitsplatte hinter dem Gerät vor. 3. Heben Sie die Arbeitsplatte an und bewegen Sie sie aus den vorderen Schlitzen heraus. 4. Stellen Sie das Gerät mit dem Schraubfuß korrekt eben. Installieren Sie das Gerät unter der Arbeitsplatte. Achten Sie darauf, dass die Wasserschläuche nicht geknickt oder eingeklemmt werden.
Wasseranschluss 55 Der Wasserdruck muss innerhalb des in den "Technischen Daten" aufgeführten Bereichs liegen. Informieren Sie sich bei Ihrem Wasserversorger über den durchschnittlichen Wasserdruck in Ihrer Region. Achten Sie darauf, dass der Wasserzulaufschlauch nicht geknickt oder gequetscht wird oder sich irgendwo verfängt. Achten Sie darauf, dass die Klemmmutter korrekt sitzt, damit kein Wasser austreten kann. VORSICHT! Schließen Sie das Gerät nicht an neue oder lange nicht mehr benutzte Leitungen an.
Elektrischer Anschluss Achten Sie darauf, dass der Wasserablaufschlauch nicht geknickt oder eingeklemmt wird, um sicherzustellen, dass das Wasser stets gut ablaufen kann. Nehmen Sie den Spülbeckenstöpsel aus dem Becken, während das Gerät das Wasser abpumpt, um zu verhindern, dass das Wasser wieder in das Gerät zurückfließt. Ein Verlängerungs-Ablaufschlauch darf nicht länger als 2 Meter sein. Der Innendurchmesser des Siphons muss mindestens genauso groß sein wie der Durchmesser des Schlauchs.
Umwelttipps 57 Umwelttipps Das Symbol auf dem Produkt oder seiner Verpackung weist darauf hin, dass dieses Produkt nicht als normaler Haushaltsabfall zu behandeln ist, sondern an einem Sammelpunkt für das Recycling von elektrischen und elektronischen Geräten abgegeben werden muss. Durch Ihren Beitrag zum korrekten Entsorgen dieses Produkts schützen Sie die Umwelt und die Gesundheit Ihrer Mitmenschen. Umwelt und Gesundheit werden durch falsches Entsorgen gefährdet.
www.electrolux.com 117951570-00-072009 Benötigen Sie Zubehör, Verbrauchsmaterial und Ersatzteile? Dann besuchen Sie bitte unseren Onlineshop unter: www.aeg-electrolux.at www.aeg-electrolux.