FAVORIT EXPRESS VI User manual Benutzerinformation Dishwasher Geschirrspüler
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information 3 Operating instructions Safety information For your safety and correct operation of the appliance, read this manual carefully before installation and use. Always keep these instructions with the appliance even if you move or sell it. Users must fully know the operation and safety features of the appliance. Correct use • • • • • • • • • • The appliance is designed exclusively for domestic use. Only use the appliance to clean household utensils that are applicable for dishwashers.
Product description Installation • Make sure that the appliance is not damaged because of transport. Do not connect a damaged appliance. If necessary, contact the supplier. • Remove all packaging before first use. • A qualified and competent person must do the electrical installation. • A qualified and competent person must do the plumbing installation. • Do not change the specifications or modify this product. Risk of injury and damage to the appliance.
Control panel 6 7 8 9 5 Rating plate Filters Lower spray arm Upper spray arm Optical signal After the start of the washing programme, an optical signal shows on the floor below the appliance door. If the appliance is installed higher with a flush kitchen furniture door, the optical signal will not be visible. Optical signal The red light is on. Indication of the start of a washing programme. The red light stays on during the washing programme. The red light flashes. Indication of a malfunction.
Control panel Indicator lights Salt 1) Comes on when it is necessary to fill the salt container. Refer to 'Use of dishwasher salt'. After you fill the container, the salt indicator light can continue to stay on for some hours. This does not have an unwanted effect on the operation of the appliance. Rinse aid 1) Comes on when it is necessary to fill the rinse aid dispenser. Refer to 'Use of rinse aid'. End-of-programme Comes on when the washing programme is completed.
Control panel 7 Multitab button Press this button to activate/deactivate the multitab function. Refer to the chapter 'Multitab function'. Half-load button The half-load option is not available for all washing programmes. Refer to the chapter 'Washing programmes'. • Load dishes in the upper and lower basket. • Decrease the detergent dosage when you use the half-load option. • Press the half-load button to set the option. – The half-load indicator light comes on, when the half-load option is selectable.
Use of the appliance 3. Press and hold function buttons B and C until the indicator lights of function buttons A, B and C start to flash. 4. Release function buttons A and B. 5. Press the function button C. – Indicator lights for function buttons A and B go off. – Indicator light for function button C flashes. – The digital display shows the setting. Audible signals deactivated Audible signals activated The audible signals are activated. 6. Press the function button C again.
Setting the water softener Water hardness 9 Water hardness setting °dH °TH mmol/l Clarke manually electronically 51 - 70 91 - 125 9,1 - 12,5 64 - 88 2 10 43 - 50 76 - 90 7,6 - 9,0 53 - 63 2 9 37 - 42 65 - 75 6,5 - 7,5 46 - 52 2 8 29 - 36 51 - 64 5,1 - 6,4 36 - 45 2 7 23 - 28 40 - 50 4,0 - 5,0 28 - 35 2 6 19 - 22 33 - 39 3,3 - 3,9 23 - 27 2 5 15 - 18 26 - 32 2,6 - 3,2 18 - 22 1 4 11 - 14 19 - 25 1,9 - 2,5 13 - 17 1 3 4 - 10 7 - 18 0,7 - 1,8 5 - 12
Use of dishwasher salt Example: digital display shows / 5 intermittent audible signals = level 5. 6. Press the function button A one time to increase the water softener level by one step. 7. Press the on/off button to save the operation. Use of dishwasher salt CAUTION! Only use dishwashers salt. Types of salt that are not applicable for dishwashers cause damage to the water softener. CAUTION! Grains of salt and salty water on the bottom of the appliance can cause corrosion.
Use of rinse aid 11 1. Press the release button (A) to open the rinse aid dispenser. 2. Fill the rinse aid dispenser with rinse aid. The mark 'max.' shows the maximum level. 3. Remove the spilled rinse aid with an absorbent cloth to prevent too much foam during the subsequent washing programme. 4. Close the rinse aid dispenser. Adjusting the rinse aid dosage The rinse aid is set at the factory at position 4.
Loading cutlery and dishes Loading cutlery and dishes Helpful hints and tips CAUTION! Only use the appliance for household utensils that are applicable for dishwashers. Do not use the appliance to clean objects that can absorb water (sponges, household cloths, etc.). • Before you load cutlery and dishes, do these steps: – Remove all food remainings and debris. – Make burnt, remaining food in pans soft. • While you load cutlery and dishes, do these steps: – Load hollow items (e.g.
Loading cutlery and dishes 13 The rows of prongs in the lower basket can be flat to load large dishes, pots, pans and bowls. Cutlery basket WARNING! Do not put long-bladed knives in a vertical position. Arrange long and sharp cutlery horizontally in the upper basket. Be careful with sharp items. Use the cutlery grids. • Put the grids on the cutlery basket. • For larger items use only one of the cutlery grids. • Put forks and spoons with the handles down. • Put knives with the handles up.
Loading cutlery and dishes Upper basket The upper basket is for saucers, salad bowls, cups, glasses, pots and lids. Arrange the items to let water touch all surfaces. • For longer items fold the cup racks up. • Put glasses with long stems in the cup racks with the stems up. • For glasses with long stems, turn the glass holder to the left or to the right.
Use of detergent • You can fold up or down the row of prongs on the left side of the upper basket to increase load flexibility. Adjustment of the height of the upper basket You can put the upper basket in two positions to increase load flexibility. Maximum height of the dishes in: the upper basket the lower basket Upper position 22 cm 30 cm Lower position 24 cm 29 cm Do these steps to move to the upper basket to the lower/upper position: 1. Pull out the upper basket until it stops. 2.
Use of detergent 1. Open the lid of the detergent dispenser. 2. Fill the detergent dispenser (A) with detergent. The marking shows the dosage: 20 = approximately 20 g of detergent 30 = approximately 30 g of detergent. 3. If you use a washing programme with prewash phase, put more detergent in the prewash detergent compartment (B). A B 4. If you use detergent tablets, put the detergent tablet in the detergent dispenser (A). 5. Close the lid of the detergent dispenser.
Multitab function 17 Multitab function The multitab function is for combi detergent tablets. These tablets contain agents such as detergent, rinse aid and dishwasher salt. Some types of tablets can contain other agents. Do a check if these tablets are applicable for the local water hardness. Refer to the instructions from the manufacturer. When you set the multitab function, it stays on until you deactivate it. The multitab function stops automatically the flow of rinse aid and salt.
Washing programmes To use normal detergent again: 1. Deactivate the multitab function. 2. Fill the salt container and rinse aid dispenser. 3. Adjust the water hardness setting to the highest level. 4. Do a washing programme without dishes. 5. Adjust the water softener to the water hardness in your area. 6. Adjust the rinse aid dosage.
Washing programmes 19 Selectable options Programme Half load Save energy1) 1 AUTO 45-70° no selectable, impact on washing programme 2 INTENSIV CARE 70° yes selectable, impact on washing programme 3 30 MIN 60° no selectable, no impact on washing programme 4 ECO 50° yes selectable, impact on washing programme 5 1 HOUR 55° no selectable, no impact on washing programme 6 GLASS 45° no selectable, impact on washing programme 7 PREWASH no selectable, no impact on washing programme 1) For
Setting and starting a washing programme Setting and starting a washing programme Set the options before the start of a washing programme. You cannot set an option when a washing programme operates. If it is necessary to set an option, cancel the washing programme. Set the washing programme with the door ajar. The washing programme only starts after you close the door. Until then it is possible to modify the settings. Do these steps to set and start a washing programme: 1. Switch on the appliance. 2.
Care and cleaning 21 – When the countdown is completed, the washing programme starts automatically. Do not open the door during the countdown to prevent interruption of the countdown. When you close the door again, the countdown continues from the point of interruption. Cancelling a delay start 1. Press and hold function buttons B and C until the digital display shows two horizontal bars. – When you cancel a delay start, you also cancel the washing programme. 2. Set a new washing programme.
Care and cleaning Cleaning the filters CAUTION! Do not use the appliance without the filters. Make sure that the installation of the filters is correct. Incorrect installation will cause unsatisfactory washing results and damage to the appliance. If necessary, clean the filters. Dirty filters decrease the washing results. The dishwasher has three filters: 1. coarse filter (A) 2. microfilter (B) 3. flat filter (C) Do these steps to clean the filters: A 1. Open the door. 2. Remove the lower basket.
What to do if… 23 14. Close the door. Do not remove the spray arms. If the holes in the spray arms become clogged, remove remaining parts of soil with a cocktail stick. External cleaning Clean the external surfaces of the appliance and control panel with a damp soft cloth. Only use neutral detergents. Do not use abrasive products, scouring pads or solvents (acetone, trichloroethylene etc...). Frost precautions CAUTION! Do not install the appliance where the temperature is below 0 °C.
What to do if… Fault code and malfunction Possible cause and solution • intermittent audible signal • digital display shows The anti-flood device operates • Close the water tap and contact your local Service Force Centre. The programme does not start • The appliance door is not closed. Close the door. • Mains plug is not connected in. Put in the mains. • The fuse has blown out in the household fuse box. Replace the fuse. • Delay start is set.
Technical data 25 Technical data Dimensions Width cm 59,6 Height cm 81,8 - 89,8 Depth cm 55 Electrical connection - Voltage Information on the electrical connection is given on the rating - Overall power - Fuse plate on the inner edge of the dishwasher door. Water supply pressure Capacity Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Place settings 12 Installation instructions Installation WARNING! Make sure that mains plug is disconnected from the mains socket during installation.
Water connection Water connection Water inlet hose Connected the appliance to a hot (max. 60°) or cold water supply. If the hot water comes from alternative sources of energy that are more environmentally friendly (e.g. solar or photovoltaic panels and aeolian), use a hot water supply to decrease energy consumption. Connect the inlet hose to a water tap with an external thread of 3/4”. CAUTION! Do not use connection hoses from an old appliance.
Electrical connection 27 max 400 cm 2. Connect the water drain hose to a stand pipe with vent-hole (minimum internal diameter 4 cm). Make sure that the drain hose is not bent or max 85 cm squashed to prevent that the water drains does not drain correctly. Remove the sink plug when the appliance drains min 40 cm the water to prevent that the water goes back into the appliance. A drain hose extension must not be longer than 2 m. The internal diameter must not be smaller than the diameter of the hose.
Environment concerns and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product. The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc.
Inhalt 29 Danke, dass Sie sich für eines unserer hochqualitativen Produkte entschieden haben. Lesen Sie für eine optimale und gleichmäßige Leistung Ihres Gerätes diese Benutzerinformation bitte sorgfältig durch. Sie wird Ihnen helfen, alle Vorgänge perfekt und äußerst effizient zu steuern. Damit Sie diese Benutzerinformation bei Bedarf stets zur Hand haben, empfehlen wir Ihnen, sie an einem sicheren Ort aufzubewahren.
Sicherheitshinweise Gebrauchsanweisung Sicherheitshinweise Lesen Sie diese Bedienungsanleitung bitte sorgfältig durch, bevor Sie das Gerät anschließen und benutzen, um Gefahren zu vermeiden und einen korrekten Betrieb des Geräts zu gewährleisten. Bewahren Sie diese Bedienungsanleitung in der Nähe des Geräts auf, auch wenn Sie dieses anderswo aufstellen. Wenn Sie das Gerät verkaufen, geben Sie dem Käufer die Bedienungsanleitung mit.
Gerätebeschreibung 31 • Halten Sie das Verpackungsmaterial von Kindern fern. Andernfalls besteht Erstickungsgefahr. • Bewahren Sie alle Reinigungsmittel an einem sicheren Ort auf. Achten Sie darauf, dass Reinigungsmittel nicht in die Hände von Kindern gelangen. • Halten Sie Kinder vom geöffneten Geschirrspüler fern. Installation • Vergewissern Sie sich, dass das Gerät beim Transport nicht beschädigt wurde. Schließen Sie ein beschädigtes Gerät nicht an. Wenden Sie sich bei Bedarf an den Hersteller.
Bedienblende 1 2 3 4 5 6 7 8 9 Oberkorb Anzeige der Wasserhärtestufe Salzbehälter Behälter für Reinigungsmittel Dosiergerät für Klarspüler Typenschild Filter Unterer Sprüharm Oberer Sprüharm Optisches Signal (Programmlaufanzeige) Nach dem Start des Spülprogramms leuchtet ein optisches Signal am Boden unter der Gerätetür auf. Ist das Gerät höher mit einer bündigen Küchenmöbeltür installiert, ist das optische Signal nicht sichtbar. Optisches Signal (Programmlaufanzeige) Die rote Kontrolllampe leuchtet.
Bedienblende 1 2 3 4 5 6 7 8 9 33 Digital-Display Zeitvorwahl-Taste Programmwahltasten Energiesparen-Taste (ÖKO PLUS) Multitab-Taste (MULTITAB) Taste Halbe Beladung Kontrolllampen Ein/Aus-Taste Funktionstasten Kontrolllampen Salz 1) Leuchtet auf, wenn der Salzbehälter aufgefüllt werden muss. Siehe Abschnitt "Verwendung von Geschirrspülsalz". Die Kontrolllampe für Salz kann nach dem Nachfüllen von Salz noch einige Stunden leuchten. Dies hat jedoch keine unerwünschte Auswirkung auf den Gerätebetrieb.
Bedienblende Energiespar-Taste Diese Funktion senkt die Temperatur in der Trockenphase. Die Energieeinsparung beträgt zwischen 10 und 25 %. Falls das Geschirr am Endes des Programms noch feucht ist, lassen Sie die Tür einen Spaltbreit geöffnet, damit es von selbst weiter trocknen kann. Diese Funktion ist für alle Spülprogramme verfügbar. Die zugehörige Kontrolllampe leuchtet auf, wenn Sie die Taste drücken. Die Energiespar-Funktion hat bei manchen Programmen keine Auswirkung.
Vor der ersten Inbetriebnahme 35 Drücken Sie die Ein/Aus-Taste. Das Gerät ist nicht im Einstellmodus, wenn: – im Digital-Display die Programmdauer in Minuten angezeigt wird. – ein Spülprogramm eingestellt ist. Löschen Sie das Programm, um in den Einstellmodus zurückzukehren. Siehe Kapitel "Auswahl und Start eines Spülprogramms". Akustische Signale Sie hören einen Signalton: • Am Ende des Spülprogramms. • Während der Einstellung des Wasserhärtegrads. • Im Fall einer Fehlfunktion des Geräts.
Einstellen des Wasserenthärters Wenn Sie Reinigertabletten ('3 in 1', '4 in 1', '5 in 1', etc.) verwenden, siehe das Kapitel "Multitab-Funktion". Einstellen des Wasserenthärters Der Wasserenthärter entfernt Mineralien und Salze aus dem Spülwasser. Andernfalls könnten sich die Mineralien und Salze nachteilig auf die Funktion des Geräts auswirken. Die Wasserhärte wird in unterschiedlichen, aber gleichwertigen Einheiten gemessen: • Deutsche Wasserhärtegrade (dH°). • Französische Wasserhärtegrade (°TH).
Gebrauch von Salz für Geschirrspüler 37 1. Öffnen Sie die Tür. 2. Entfernen Sie den Unterkorb. 3. Drehen Sie die Härtebereichsanzeige auf Härtestufe 1 oder 2 (siehe die Tabelle). 4. Setzen Sie den Unterkorb ein. 5. Schließen Sie die Tür. Elektronische Einstellung Der Geschirrspüler ist werkseitig auf Härtestufe 5 eingestellt. 1. Schalten Sie das Gerät ein. 2. Achten Sie darauf, dass sich das Gerät im Einstellmodus befindet. 3.
Gebrauch von Klarspülmittel 3. Verwenden Sie den Trichter, um den Behälter mit Salz zu füllen. 4. Entfernen Sie das Salz, das sich um die Öffnung des Salzbehälters herum angesammelt hat. 5. Drehen Sie den Deckel im Uhrzeigersinn, um den Salzbehälter zu schließen. Es ist normal, dass das Wasser aus dem Salzbehälter beim Einfüllen von Salz überläuft. Wenn Sie den Wasserenthärter auf Stufe 1 einstellen, leuchtet die Salzkontrolllampe nicht mehr.
Laden von Besteck und Geschirr 39 2. Füllen Sie den Klarspüldosierer mit Klarspüler. Der maximale Füllstand wird durch die Markierung "max".angezeigt. 3. Wischen Sie verschütteten Klarspüler mit einem saugfähigen Tuch auf, um zu große Schaumbildung beim nächsten Spülprogramm zu vermeiden. 4. Schließen Sie den Klarspülerdosierer. Einstellung des Klarspüldosierers Der Wasserenthärter ist werkseitig auf Härtestufe 4 eingestellt.
Laden von Besteck und Geschirr • Achten Sie beim Einordnen von Geschirr und Besteck auf Folgendes: – Ordnen Sie Hohlgefäße (z. B. Tassen, Gläser, Pfannen) mit der Öffnung nach unten ein. – Achten Sie darauf, dass sich kein Wasser in Höhlungen oder Vertiefungen sammeln kann. – Achten Sie darauf, dass Geschirr- und Besteckteile nicht ineinander zu liegen kommen. – Achten Sie darauf, dass Geschirr- und Besteckteile nicht übereinander zu liegen kommen.
Laden von Besteck und Geschirr 41 Die Stachelreihen am Unterkorb können flach umgeklappt werden, um Servierplatten, Töpfe, Pfannen und Schüsseln einzuordnen. Besteckkorb WARNUNG! Stellen Sie keine Messer mit langen Klingen in aufrechter Stellung ein. Legen Sie langes oder scharfes Besteck waagerecht in den Oberkorb. Gehen Sie vorsichtig mit scharfen Gegenständen um. Verwenden Sie das Besteckgitter. • Setzen Sie die Gitter auf den Besteckkorb.
Laden von Besteck und Geschirr • Stellen Sie Gabeln und Löffel mit den Griffen nach unten ein. • Stellen Sie Messer mit den Griffen nach oben ein. • Mischen Sie Löffel mit anderem Besteck, damit sie nicht zusammenkleben können. Oberkorb Der Oberkorb ist zur Aufnahme von Untertassen, Salatschüsseln, Tassen, Gläsern, Töpfen und Deckeln bestimmt. Ordnen Sie das Spülgut so ein, dass das Wasser alle Oberflächen erreichen kann. • Klappen Sie die Tassenablagen zum Einordnen höherer Gegenstände nach oben.
Laden von Besteck und Geschirr 43 • Klappen Sie den Glashalter für langstielige Gläser nach links oder rechts. • Die Stachelreihe auf der linken Seite des Oberkorbs kann für eine flexiblere Beladung umgeklappt werden. Höhenverstellung des Oberkorbs Der Oberkorb kann für eine flexiblere Beladung in zwei verschiedenen Höhen in den Geschirrspüler eingeschoben werden.
Gebrauch von Spülmittel 1. Ziehen Sie den Oberkorb bis zum Anschlag heraus. 2. Halten Sie den Oberkorb am Griff, heben Sie ihn bis zum Anschlag an und senken Sie ihn dann senkrecht ab. Der Oberkorb rastet in der unteren oder oberen Position ein. Gebrauch von Spülmittel Verwenden Sie ausschließlich Spülmittel (Pulver, Flüssigspülmittel oder GeschirrspülerTabs) speziell für Geschirrspüler. Richten Sie sich nach den Angaben auf der Verpackung: • Vom Hersteller empfohlene Dosierung.
Funktion "Multitab" 45 3. Geben Sie bei einem Spülprogramm mit Vorspülgang zusätzlich etwas Spülmittel ins Vorspülfach ( B). A B 4. Wenn Sie Geschirrspüler-Tabs verwenden, legen Sie diese in den Reinigungsmittelbehälter ( A). 5. Schließen Sie den Deckel des Spülmittelbehälters. Drücken Sie auf den Deckel, bis er einrastet. Spülmittel unterschiedlicher Marken lösen sich unterschiedlich schnell auf. Einige Geschirrspüler-Tabs erbringen bei kurzen Spülprogrammen keine optimalen Ergebnisse.
Funktion "Multitab" Schalten Sie die Funktion Multitab vor dem Beginn eines Spülprogramms ein oder aus. Sie können die Funktion Multitab nicht ein- oder ausschalten, wenn das Programm angelaufen ist. Brechen Sie das Spülprogramm ab und stellen Sie das Programm dann erneut ein. Schalten Sie die Funktion Multitab wie folgt ein: • Drücken Sie die Multitab-Taste. Die Multitab-Kontrolllampe leuchtet auf. Schalten Sie die Funktion Multitab wie folgt aus: • Drücken Sie die Multitab-Taste.
Spülprogramme 47 Spülprogramme Spülprogramme Programm Grad der Verschmutzung Spülgut Programmbeschreibung 1 AUTO 45-70°1) Beliebig Geschirr, Besteck, Töpfe, Pfannen Vorspülgang Hauptspülgang bis zu 45 °C oder 70 °C 1 oder 2 Zwischenklarspülgänge Klarspülgang Trocknen 2 INTENSIV CARE 70° Stark verschmutzt Geschirr, Besteck, Töpfe, Pfannen Vorspülgang Hauptspülgang bis zu 70 °C 1 Zwischenspülgang Klarspülgang Trocknen 3 30 MIN 60° 2) Normal/leicht verschmutzt Geschirr und Besteck Hauptspülgan
Spülprogramme Programm Halbe Beladung Energiesparen 1) 2 INTENSIV CARE 70° Ja Wählbar, mit Auswirkung auf das Spülprogramm 3 30 MIN 60° Nein Wählbar, keine Auswirkung auf das Spülprogramm 4 ECO 50° Ja Wählbar, mit Auswirkung auf das Spülprogramm 5 55° 1 STUNDE Nein Wählbar, keine Auswirkung auf das Spülprogramm 6 45° GLAS Nein Wählbar, mit Auswirkung auf das Spülprogramm 7 VORSPÜLGANG Nein Wählbar, keine Auswirkung auf das Spülprogramm 1) Bei Programmen, auf die sich die Option ausw
Auswählen und Starten eines Spülprogramms 49 Auswählen und Starten eines Spülprogramms Stellen Sie die Optionen vor dem Beginn eines Spülprogramms ein. Wenn ein Spülprogramm bereits läuft, können Sie keine Optionen einstellen. Wenn es erforderlich ist, eine Option einzustellen, löschen Sie das Spülprogramm. Wählen Sie das Spülprogramm bei geöffneter Tür. Das Spülprogramm startet erst nach dem Schließen der Tür. Bis dahin können die Einstellungen noch geändert werden.
Reinigung und Pflege – Der Ablauf der Zeitvorwahl beginnt. – Nach dem Ablauf der Zeitvorwahl beginnt das Spülprogramm automatisch. Öffnen Sie die Tür während des Ablaufs der Zeitvorwahl nicht, um eine Unterbrechung der Zeitvorwahl zu verhindern. Nachdem Sie die Tür wieder geschlosssen haben, läuft die Zeitvorwahl ab dem Unterbrechungszeitpunkt weiter ab. So löschen Sie die Zeitvorwahl 1.
Reinigung und Pflege 51 Filterreinigung VORSICHT! Verwenden Sie das Gerät nicht ohne Filter. Achten Sie darauf, die Filter korrekt einzusetzen. Sind die Filter falsch eingesetzt, spült das Gerät nicht zufriedenstellend und kann beschädigt werden. Reinigen Sie die Filter bei Bedarf. Schmutzige Filter beeinträchtigen das Spülergebnis. Der Geschirrspüler hat 3 Filter: 1. Grobfilter (A) 2. Mikrofilter (B) 3. Flachfilter (C) Gehen Sie wie folgt vor, um die Filter zu reiniA gen: 1. Öffnen Sie die Tür. 2.
Was tun, wenn … 12. Um das Filtersystem zu arretieren, drehen Sie den Griff des Mikrofilters (B) im Uhrzeigersinn, bis er einrastet. 13. Setzen Sie den Unterkorb ein. 14. Schließen Sie die Tür. Nehmen Sie die Sprüharme nicht heraus. Wenn die Löcher in den Sprüharmen verstopft sind, entfernen Sie Verschmutzungen mit einem Cocktail-Stick. Reinigung der Außenseiten Reinigen Sie die Außenseiten und die Bedienblende des Geräts mit einem weichen feuchten Tuch.
Was tun, wenn … Fehlercode und Störung 53 Mögliche Ursachen und Abhilfe • Akustische Signalabfolge • Der Siphon ist verstopft. • Das Digital-Display zeigt an Reinigen Sie den Siphon. Der Geschirrspüler pumpt nicht ab • Der Wasserablaufschlauch ist falsch angeschlossen. Möglicherweise ist der Schlauch geknickt oder gequetscht. Achten Sie auf einen korrekten Anschluss des Schlauchs.
Technische Daten Das Spülergebnis ist nicht zufriedenstellend Das Geschirr ist nass und glanzlos • Es wurde kein Klarspüler verwendet. • Der Klarspüldosierer ist leer. Schlieren, Streifen, milchige • Verwenden Sie weniger Klarspüler. Flecken oder blau schimmernde Beläge befinden sich auf Gläsern und Geschirr Getrocknete Wassertropfen befinden sich auf Gläsern und Geschirr • Verwenden Sie mehr Klarspüler. • Die Ursache kann beim Spülmittel liegen.
Wasseranschluss 55 Vergewissern Sie sich vor dem Einbau des Geräts, dass der Wasserzulauf- und der Wasserablaufschlauch sowie das Netzkabel weder geknickt noch gequetscht werden. Einpassen des Geräts an bzw. zwischen die angrenzenden Küchenmöbel Vergewissern Sie sich, dass die Arbeitsplatte, unter die der Geschirrspüler eingeschoben wird, ordnungsgemäß und sicher (an benachbarbarten Küchenschränken/-möbeln, Wänden usw.) befestigt ist.
Wasseranschluss WARNUNG! Gefährliche Spannung Ablaufschlauch max 400 cm 1. Schließen Sie den Ablaufschlauch an den Siphon an und befestigen Sie ihn an der Unterseite der Arbeitsplatte. Dadurch wird verhindert, dass Abwasser aus dem Siphon in das Gerät zurückfließen kann. 2. Schließen Sie den Ablaufschlauch an ein Standrohr mit Belüftungsöffnung an (Mindestdurchmesser des Innenrohres 4 cm).
Elektrischer Anschluss 57 Elektrischer Anschluss WARNUNG! Der Hersteller haftet nicht für Schäden aufgrund der Nichtbeachtung folgender Sicherheitshinweise. Erden Sie das Gerät gemäß den Sicherheitshinweisen. Vergewissern Sie sich, dass die Netzspannung und -frequenz in Ihrer Region mit den auf dem Typenschild angegebenen Anschlusswerten übereinstimmen. Schließen Sie das Gerät unbedingt an eine sachgemäß installierte Schutzkontaktsteckdose an.
www.electrolux.com 117951620-00-082009 Benötigen Sie Zubehör, Verbrauchsmaterial und Ersatzteile? Dann besuchen Sie bitte unseren Onlineshop unter: www.aeg-electrolux.at www.aeg-electrolux.