FAVORIT 35080 i Dishwasher User information
Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Diagram of appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Prior to using for the first time . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. Correct use • The dishwasher is only intended for washing domestic dishes. • Additions or modifications to the dishwasher are not permitted. • Use only special salt, detergent and rinse aid suitable for domestic dishwashers. • Do not put any solvents in the dishwasher. This could cause an explosion. Child safety • Keep packaging away from children. There is a risk of suffocation.
Diagram of appliance Upper basket spray arm and floor spray arm Water hardness dial Dispenser for special salt Dispenser for detergent Dispenser for rinse aid Rating plate Filters Control panel 5
Power indicator End of cycle indicator Programme progress display Control knob Control indicators Start button Set delay timer The control knob is used to select the desired dishwashing cycle. In the Off position the line points vertically upwards. The Start button is used to: – start the dishwasher – set the water softener – cancel a dishwashing cycle. Programme progress display: The current stage of the programme is always shown in the programme progress display.
Prior to using for the first time 3 If you wish to use 3 in 1 detergent: – First read the section “Using 3in1 detergents”. – Do not fill up with special salt or rinse aid. If you do not use 3in1 detergent, before using for the first time 1. Set the water softener 2. Fill up with special salt for water softeners 3.
. If the hardness setting is correctly set, turn control knob to the Off position. The hardness setting is now saved. If the water softener is set electronically to “1”, this switches off the control indicator for special salt. Adjusting the hardness setting Water hardness in °d1) in mmol/l2) 51 - 70 43 - 50 37 - 42 29 - 36 23 - 28 9,0 - 12,5 7,6 - 8,9 6,5 - 7,5 5,1 - 6,4 4,0 - 5,0 IV 19 - 22 15 - 18 3,3 - 3,9 2,6 - 3,2 III 11 - 14 1,9 - 2,5 II 4 - 10 0,7 - 1,8 I/II below 4 below 0.
Adding special salt 3 3 To decalcify the water softener, it must be filled up with special salt. Use only special salt suitable for domestic dishwashers. If you do not use 3 in1 detergent, fill up with special salt: – Before using the dishwasher for the first time. – When the control indicator for special salt is illuminated on the control panel. 1. Open the door and remove the lower basket. 2. Screw open the lid on the salt dispenser by turning it anti-clockwise. 3.
Filling up with rinse aid With rinse aid the rinsing water drains away better and so you get smear-free, gleaming dishes and clear glasses. If you do not use 3in1 detergent, fill up with rinse aid: – Before using the dishwasher for the first time. – When the control indicator for rinse aid is illuminated on the control panel. Use only special rinse aid for dishwashers and no other liquid detergents. 1. Open the door. The rinse aid compartment is located on the inside of the dishwasher door. 2.
Setting the amount of rinse aid required 3 Only change the amount dispensed, if smears, milky spots (reduce the amount) or dried on water spots (increase the amount) can be seen on glasses and dishes. (See section “If dishwashing results are not satisfactory”.) The dosage can be set from 1-6. The dosage is pre-set to “4” in the factory. 1. Open the dishwasher door. 2. Press the release button on the rinse aid compartment. 3. Open the cover. 4. Set the dosage level. 5.
In daily use Loading cutlery and dishes 1 Sponges, cleaning cloths and any other objects that can absorb water must not be washed in the dishwasher. Plastic and Teflon-coated dishes and pans tend to retain water droplets. These dishes and pans therefore do not dry as well as those made of china and stainless steel.
Loading cutlery 1 Warning: Sharp knives and other items of cutlery with sharp edges must be laid in the cutlery rack or in the upper basket to avoid the risk of injury. To ensure that all items of cutlery in the cutlery basket can be reached by the water, you should: 1.Place the grid insert on the cut- 2.Place forks and spoons in the lery basket cutlery basket's grid insert with their handles pointing downwards. For larger utensils, such as whisks, leave off one half of the cutlery grid.
To make it easier to load larger dishes, the two plate rests on the right in the lower basket can be folded down. Cups, Glasses, Coffee Service Load smaller, fragile crockery and long, sharp cutlery in the upper basket. • Arrange items of crockery on and under the folding cup racks so that they are offset from each other and water can reach all items. • The cup racks can be folded up out of the way for tall crockery items. • Lay or hang wine and brandy glasses in the slots in the cup racks.
Adding detergent 1 Detergents remove the dirt from dishes and cutlery. The detergent must be added before the cycle starts. Only use detergent intended for domestic dishwashers. The detergent compartment is located on the inside of the door. 1. If the lid is closed: Press the release button. The lid will spring open. 3 2. Place the detergent in the detergent dispenser. The markings indicate the dosing levels for powder detergents: “20/30” corresponds to approx. 20/30 ml of detergent.
Concentrated detergents 2 Today’s detergents for dishwashers are almost exclusively low-alkaline concentrated detergents with natural enzymes in tablet or powder form. Using 50°C dishwashing cycles in conjunction with these concentrated detergents reduces pollution and is good for your dishes, as these dishwashing cycles are specially matched to the dirt-dissolving properties of the enzymes in concentrated detergents.
Selecting the dishwashing cycle (Cycle Table) Drying • - • - • • • • • • • • • 150 0,95 - 1,05 18 • - - - - 12 < 0,1 4 ECO 50°4) Dinner service and cookware, temperaturesensitive crockery normally soiled All types of dishes Used dishes that are being stored in the dishwasher and are to be washed later.
Selecting a programme When your dishes look like this, select: an intensive programme. a normal or energy-saving programme. a short programme (e.g. 30 minute programme).
Starting a dishwashing cycle 1. Check that the spray arms can turn freely. 2. Turn the water tap on fully. 3. Close the door. 4. Select the desired cycle. The programme progress indicators flash. 5. Press Start button. The dishwashing cycle starts. Interrupting or aborting a dishwashing cycle Only interrupt a dishwashing cycle that is in progress if it is absolutely necessary. 1 Interrupting the dishwashing programme by opening the dishwasher door Hot steam may escape when the door is opened.
Setting the Delay Timer With the delay timer you can delay the start of a dishwashing cycle for 3 hours. 1. Select dishwashing cycle. The programme progress indictors flash. 2. Press Delay Timer button. The indicator above the number of hours lights up. 3. Press Start button. The programme progress indictors go out. The dishwashing cycle will start automatically when 3 hours have elapsed. Cancelling the delay timer: Press the delay timer button. The hours indicator goes out.
Care and cleaning 1 Do not use furniture care products or aggressive cleaners. • When necessary, clean the dishwasher’s controls with a soft cloth and clean warm water. • Occasionally check the internal dispensers, door seal and water inlet filter (if fitted) for dirt and clean them, if necessary. Cleaning the filters 3 The filters must be regularly checked and cleaned. Dirty filters will spoil the wash results. 1. Open the door and remove the lower basket. 2.
5. Remove the flat filter (3) from the base of the washing compartment and clean both surfaces thoroughly. 6. Re-insert the flat filter. 7. Place the fine filter in the micro-filter and fit the two together. 8. Insert the filter system in place and lock it by turning the handle clockwise as far as it will go. Ensure that the flat filter does not protrude above the base of the washing compartment. 1 Under no circumstances may the dishwasher be used without its filters.
3. Place cleaned upper basket spray arm back in position against the connecting piece: press the two together firmly, until you feel them snap into place. Bottom spray arm 1. To remove bottom spray arm, pull it upwards out of its catch. 2. Clean spray arm jets. 3. Place bottom spray arm back in position against connecting piece and press down firmly, until you feel it snap into place.
What to do if... Remedying small malfunctions If while the appliance is operating indicators on the control panel flash or are lit up as described in the following table, please consult this to find out how to remedy the fault. After remedying the fault that is flashing in the first or second rhythm in the programme progress display, press the start-button. The cycle will continue. In the case of other fault messages: – Cancel the dishwashing cycle. – Switch the appliance off and on again.
Malfunction Possible cause The indicator for the end of the dishwashing cycle is The anti-flood system has flashing in rhythm 3 short been triggered. light signals one after another. The mains plug is not plugged in. The cycle is not starting. Remedy Turn off the tap and contact the Customer Care Department. Connect the plug to a mains socket. A fuse in the house’s wiring Replace fuse. system is defective.
If the dishwashing results are not satisfactory The dishes are still dirty. • The wrong dishwashing cycle was selected. • The dishes were loaded is such a way that the dishwashing water did not reach all items. The baskets for the dishes must not be overloaded. • The filters in the base of the washing compartment are dirty or incorrectly positioned. • Good quality detergent was not used, or too little was used.
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W 1 The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Technical data Capacity: 12 place settings including serving dishes Permitted water pressure: 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Electrical connection: 230 V, 10 A, also see the rating plate on the right-hand side of the dishwasher’s interior door . Dishwashers that can be integrated and built-in 5 28 Dimensions: 820 - 880 x 596 x 570 (H x W x D in mm) Max. weight: 50 kg This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.
Notes for Test Institutes Testing in accordance with EN 60704 must be carried out with the appliance fully loaded and using the test cycle (see “Cycle Table”). Tests in accordance with EN 50242 must be carried out when the salt dispenser in the water softener and the rinse aid dispenser have been filled with salt and rinse aid respectively, and using the test cycle (see “Cycle Table”).
Lower basket with cutlery basket*) Cutlery basket *) If there are cup racks in place on the lefthand side or if beer glass holders are in place, remove them.
Installation and connection instructions 1 Safety information for the installation • Only transport the dishwasher in an upright position, otherwise salt water may run out. • Before using the dishwasher for the first time, check for any damage caused in transport. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier.
Installing the dishwasher • The dishwasher must be installed on a firm floor and adjusted to ensure that it is stable and level in all directions. • To compensate for unevenness in the floor and to match the height of the appliance to that of surrounding units, extend the threaded feet using a screwdriver. • Adjust the rear feet of the appliance using a cordless screwdriver from the front of the appliance. (See installation instructions.
Connecting the dishwasher Connecting to the water supply • The dishwasher can be connected to cold and hot water supplies up to max. 60°C. • The dishwasher must not be connected to open hot water appliances or instantaneous water heaters. Permitted water pressure Lowest permitted water pressure: 1 bar (=10 N/cm2 =100 kPa) Consult your plumber if the water pressure is less than 1 bar.
Water drainage 1 Drain hose The drain hose must not be kinked, crushed or entangled. Connecting the drain hose: – Maximum permitted height: 1 metre. – Minimum required height: 40 cm above the bottom edge of the appliance. Extension hoses • Extension hoses are available from your dealer or from our Customer Care Department. To ensure that the function of the appliance is not impeded, the internal diameter of extension hoses must be 19 mm.
Electrical connection Details about the voltage, type of supply and the fuses required are to be found on the rating plate. The rating plate is located on the righthand inner edge of the dishwasher door. To isolate the dishwasher from the mains, pull out the mains plug. Important: – The plug must be accessible after the appliance has been installed. – Following installation, live parts and insulated wiring must not be accessible to a test finger in accordance with DIN EN 60335-1.
Guarantee Conditions Belgium DECLARATION OF GUARANTEE TERMS. Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result. This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code.
withstand the local climatic and environmental conditions. For appliances purchased abroad, the user must first ensure that they meet the qualifications required in Belgium. Non-essential or requested adjustments are not covered by the guarantee and are not possible in all cases. Our consumer services department is always at your disposal, even after the guarantee period has expired. Address for our consumer services department: ELECTROLUX HOME PRODUCTS BELGIUM Bergensesteenweg, 719 - 1502 LEMBEEK Tel.: 02.
Customer Service Centres Belgium Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek E-mail: consumer.services@electrolux.be 38 Consumer services Tel.: 02/363.04.44 Fax.: 02/363.04.00 02/363.04.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.