FAVORIT SILENCE Lave-vaisselle automatique Informations pour les utilisateurs
Chère cliente, cher client, Veuillez lire attentivement la notice d’utilisation dans son intégralité et la conserver pour pouvoir le consulter ultérieurement. Veuillez la transmettre à l’éventuel propriétaire ultérieur de l’appareil. 1 3 2 2 Les symboles suivants sont utilisés dans ce document : Consignes de sécurité Avertissement ! Conseils pour votre sécurité personnelle. Avertissement ! Consignes permettant d’éviter d’endommager l’appareil.
Sommaire Notice d'utilisation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Vue d’ensemble de l’appareil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Bandeau de commande. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Avant la première mise en service . . . . . . . . . . . . .
Notice d'utilisation 1 Sécurité Avant la première mise en service • Veuillez respecter les “Instructions d’installation et de raccordement” Utilisation réglementaire • Le lave-vaisselle est uniquement destiné à un usage domestique. • Il est interdit de procéder à des transformations ou à modifications sur l’appareil. • Utilisez uniquement des sels spéciaux, des produits vaisselle ou de rinçage adaptés à un lave-vaisselle domestique. • Ne versez pas de solvant dans le lave-vaisselle.
Consignes générales de sécurité • Les réparations du lave-vaisselle sont du ressort exclusif de spécialistes agréés. • En cas d’arrêt du fonctionnement, mettez l’appareil hors tension et fermez le robinet d’arrivéé d’eau. • Ne tirez jamais sur le câble d’alimentation pour débrancher l’appareil, mais saisissez-le au niveau de la prise. • Veillez à ce que la porte du lave-vaisselle soit toujours fermée sauf pour placer ou retirer la vaisselle.
Vue d’ensemble de l’appareil Douche-voûte Bras d’aspersion du panier supérieur et bras d’aspersion inférieur Réglage du degré de dureté de l’eau Distributeur de sel spécial Distributeur de produit vaisselle Distributeur de produit de rinçage Plaque signalétique Filtres Bandeau de commande Touche MARCHE/ARRET La touche MARCHE/ARRET permet de mettre le lave-vaisselle sous/ hors tension.
Touches programme 1 2 3 Touches de fonction Panneau multifonctionnel Sélection du départ différé Sélection de la fonction 3 en 1 Voyants de contrôle Les touches programme permettent de sélectionner le programme de lavage souhaité.
Les voyants de contrôle ont les significations suivantes : 1) Versez le sel spécial 1) Versez le produit de rinçage 1) Ces voyants de contrôle ne s’allument pas lorsqu’un programme de lavage est en cours. Avant la première mise en service 3 Pour utiliser un produit de lavage 3 en 1 : – Lisez d’abord le chapitre “Utilisation de produits de lavage 3 en 1”. – Versez ni de sel spécial ni de produit de rinçage. Si vous n’utilisez aucun produit de vaisselle 3 en 1 avant la première mise en service: 1.
3 Réglage automatique : 1. Appuyez sur la touche MARCHE/ARRET. Si seul le voyant lumineux correspondant à la touche d’un programme s’allume, ce programme de lavage est activé. Ce programme doit être désactivé : Appuyez simultanément sur les touches de fonction 2 et 3 pendant env. 2 secondes. Tous les voyants lumineux correspondant aux touches programme s’allument. 2. Maintenir simultanément les touches de fonction 2 et 3 enfoncées. Les voyants correspondant aux touches de fonction 1 à 3 clignotent. 3.
2) (mmol/l) millimol par litre est l’unité internationale de mesure de la dureté de l’eau. 3) Ce réglage peut susciter une légère prolongation du programme. *) Préréglage en usine Verser le sel spécial 3 3 10 Pour détartrer l’adoucisseur d’eau, il est nécessaire d’utiliser du sel spécial. Utilisez uniquement des sels spéciaux adaptés à un lave-vaisselle domestique. Si vous n’utilisez pas de produit vaisselle 3 en 1, versez le sel spécial : – Avant la première mise en service du lave-vaisselle.
Verser le produit de rinçage Le produit de rinçage permet à l’eau de mieux s’écouler et d’obtenir une vaisselle étincelante et sans traces ainsi que des verres transparents. Si vous n’utilisez pas de produit vaisselle 3 en 1, versez le produit de rinçage : – Avant la première mise en service du lave-vaisselle. – Lorsque le voyant de contrôle pour produit de rinçage s’allume sur le bandeau de commande.
Régler le dosage du produit de rinçage 3 12 Ne modifiez pas le dosage du produit de rinçage à moins que les verres ou la vaisselle ne présentent des stries ou des taches blanchâtres (diminuez le dosage) ou bien traces de gouttes d’eau (augmentez le dosage) (voir chapitre “Lorsque le résultat du lavage n’est pas satisfaisant”). Le dosage peut être réglé de 1 à 6. Le préréglage effectué en usine est de “4”. 1. Ouvrez la porte du lave-vaisselle. 2.
Activation du distributeur de produit de rinçage après sélection de la fonction 3 en 1 3 3 Le distributeur de produit de rinçage est toujours activé si la fonction 3 en 1 n’a pas été sélectionnée. Si la fonction 3 en 1 a été sélectionnée suite à l'utilisation d’un produit nettoyant 3 en 1, le distributeur de produit de rinçage est éteint.
Utilisation au quotidien Disposition des couverts et de la vaisselle 1 Ne lavez pas d’éponges, de torchons de cuisine ou tout autre type d’objet susceptible de s’imbiber d’eau dans le lave-vaisselle. Les pièces dotées d’un revêtement en matière plastique ou en téflon retiennent fortement les gouttes d’eau. C’est la raison sur laquelle ce type de vaisselle sèche plus difficilement que la vaisselle en porcelaine ou en acier inoxydable.
– Les verres ne doivent pas se toucher afin d’éviter qu’ils s’endommagent – Les objets de petite taille (par ex. les couvercles) ne doivent pas être placés dans les panirs à vaisselle mais dans le panier à couvert pour éviter qu’ils se renversent. Disposer la vaisselle 1 Attention : Pour éviter tout danger de blessure, les couteaux pointus et les pièces de vaisselle contondantes doivent être disposés dans le panier supérieur.
Disposez les plats, les poêles et les grandes assiettes ainsi que la vaisselle de grande taille et très sale dans le panier inférieur (assiettes d’un diamètre pouvant aller jusqu’à 29 cm). Afin de faciliter le disposition des pièces de vaisselle de grande dimension, tous les supports d’assiettes du panier inférieur sont rabattables. Disposer les tasses, les verres, les services à café les petites pièces de vaisselle fragiles et les couverts longs et acérés dans le panier supérieur.
• Laissez les support de tasses rabattus vers le haut si les pièces de vaisselle sont hautes. • Appuyez ou accrochez les verres à vin ou à cognac dans les interstices des supports de tasses.
Verser le produit vaisselle 1 3 18 Les produits vaisselle éliminent les salissures qui se sont déposées sur la vaisselle et les couverts. Le produit vaisselle doit être versé avant de commencer un programme de lavage. Utilisez uniquement un produit vaisselle adapté à la vaisselle domestique. Le distributeur de produit de rinçage se trouve à l’intérieur de la porte du lave-vaisselle. 1. Si le couvercle est fermé : Appuyez sur le bouton de déverrouillage. Le couvercle se soulève. 2.
Produit vaisselle compact 2 Les produits vaisselle actuels sont tous quasiment des produits compacts sous forme de tablettes ou de poudre qui intégrent des enzymes naturels. La combinaison de programmes à 50 °C et de ces produits vaisselle compacts protègent l’environnement et ménagent votre vaisselle, ce type de programmes étant spécifiquement adapté aux propriétés nettoyantes des produits vaisselle compacts.
Utilisation de produits vaisselle 3 en 1 3 3 Ces produits vaisselle combinent les fonctions de produit de nettoyage, de rinçage et de sel spécial. Avec l’activation de la fonction 3in1 – L’alimentation en sel spécial et en produit de rinçage à partir des compartiments correspondants est désactivée par l’activation de la fonction 3 en 1. – Les carences en sel et en produits de rinçage ne sont plus indiquées. – Les programmes de rinçage peuvent durer 30 minutes de plus.
Si vous utilisez des produits de vaissellle 4 en 1. Lorsque vous utilisez des détergents "4 en 1" qui intègrent un agent de prévention de la corrosion du verre à une formule "3 en 1", veuillez suivre les instructions données pour les détergents "3 en 1".
Sélectionner un programme En fonction de l’aspect de la vaisselle, sélectionner : un programme intensif. un programme normal ou économique. un programme court (par ex. un programme de 30 minutes).
Démarrer le programme de lavage 3 1. Vérifiez que les bras d’aspersion peuvent tourner librement. 2. Ouvrez intégralement le robinet d’arrivée d’eau. 3. Fermez la porte. 4. Appuyez sur la touche MARCHE/ARRET. 5. Sélectionnez le programme souhaité Le voyant correspondant au programme s’allume. Le panneau multifonctionnel affiche la durée restante prévue du programme.
Réglage du départ différé 3 Le départ différé permet de retarder le départ d’un programme de lavage de 1 à 19 heures. 1. Appuyez sur la touche Départ différé jusqu’à ce que la durée du délai souhaité s’affiche sur le panneau multifonctionnel. par ex. 12 h, lorsque le programme de lavage doit démarrer dans 12 heures. Le voyant correspondant au départ différé s’allume. 2. Sélectionnez un programme de lavage. 3. Le temps restant jusqu’au départ du programme de lavage s’affiche immédiatement (par ex.
Vider le lave-vaisselle 3 Il est normal que l’intérieur de la porte et de l’appareil soient humides. • Commencez par vider le panier supérieur puis le panier inférieur. Cela évite que l’eau résiduelle ne s’égoutte du panier supérieur sur la vaisselle se trouvant dans le panier inférieur. Entretien et nettoyage 1 N’utilisez pas d’encaustique pour meubles ou de produits de nettoyage aggressifs. • Lavez les éléments de commande du lave-vaisselle à l’aide d’un chiffon humide et de l’eau chaude claire.
5. Retirez le filtre de surface (3) hors de la zone de lavage et nettoyez-le soigneusement des deux côtés. 6. Replacez le filtre de surface. 7. Insérez le filtre fin dans le microfiltre et assemblez-les. 8. Replacez le dispositif de filtrage en tournant la poignée dans le sens des aiguilles d’une montre jusqu’à la butée pour le verrouiller. Assurez-vous que le filtre de surface ne dépasse pas sur le fond de la zone de lavage. 1 N’effectuez jamais un programme de lavage sans les filtres.
3. Replacez le bras d’aspersion du panier supérieur sur la pièce de raccord en l’inclinant : exercez une forte pression sur ces deux derniers jusqu’à ce qu’ils soient complètement enclenchés (vous entendrez un clic). Bras d’aspersion inférieur 1. Retirez le bras d’aspersion inférieur de sa position enclenchée en le tirant vers le haut. 2. Nettoyez les injecteurs du bras d’aspersion. 3.
Que faire, si… Réparer soi-même de petits dysfonctionnements Au cas où un des codes d’erreur suivants s’affiche sur le panneau multifonctionnel lorsque l’appareil est en fonctionnement : – Code d’erreurÅ 10 (problème d’alimentation d’eau), – Code d’erreurÅ 20 (problème de vidange d’eau), veuillez vous référer au tableau ci-après. Après avoir réparé le dysfonctionement, appuyez sur la touche du programme en cours. Le programme de lavage se poursuit.
Symptôme Le voyant du déroulement du programme sélectionné clignote, le panneau multifonctionnel affiche le code d’erreur Å 20 : (problème de vidange). Le panneau multifonctionnel affiche le code d’erreur Å 30. Cause possible Solution Le siphon est obstrué. Nettoyez le siphon. Le tuyau de vidange Vérifiez la disposition du n’est pas correctement instuyau. tallé.
Symptôme Cause possible Solution La zone de lavage est en acier inoxydable. Les taches de rouille qui apparaissent dans la zone de lavage sont provoquées par Des taches de rouille apdes agents extérieurs (parNe lavez que les couverts et paraissent dans la zone de ticules de rouille provenant la vaisselle autorisés. lavage. de la conduite d’alimentation d’eau, de casseroles, des couverts, etc.). Eliminez les taches à l’aide d’un produit de nettoyage de l’acier inoxydable courant.
Si le résultat du lavage n’est pas satisfaisant La vaisselle n’est pas propre. • Le produit vaisselle utilisé est inadéquat. • La vaisselle est disposée de telle sorte que l’eau n’atteint pas toutes les pièces. Ne surchargez pas les paniers à vaisselle. • Les filtres au fond de la zone de lavage ne sont pas propres ou ils ne sont pas correctement installés. • Les lignes repères de remplissage du produit vaisselle ne sont pas été respectées ou le dosage est insuffisant.
Protection de l’environnement 2 2 Elimination du matériel d’emballage Les matériaux d’emballage sont écologiques et recyclables. Les matières plastiques portent un signe distinctif, par ex. >PE<, >PS<, etc. Eliminez les matériaux d’emballage en fonction de leur signe distinctif dans les containeurs prévus à cet effet sur le site de collecte de votre commune. Appareils usagés W 1 32 Le symbole sur le produit ou son emballage indique que ce produit ne peut être traité comme déchet ménager.
Caractéristiques techniques Contenance : 12 couverts standard y compris la vaisselle de service Pression de l’eau admissible : 1-10 bar (=10-100 N/cm2 = 0.1-1.0 MPa) Branchement électrique : 230 V, 10 A, voir plaque signalétique située sur le bord intérieur droit de la porte du lave-vaisselle Puissance totale installée 2250 W Lave-vaisselle : Appareils ”Pose libre“ (sur socle) 5 Dimensions : 850 x 598 x 598 (H x L x P en mm) Poids max.
Remarques destinées aux organismes de contrôle Le contrôle de conformité à l’EN 60704 doit être effectué avec un plein chargement à l’aide du programme de test (voir tableau des programmes). Les contrôles de conformité à l’EN 50242 doivent être effectués avec l’adoucisseur d’eau rempli de sel spécial, avec le distributeur de produit de rinçage plein, à l’aide du programme de test (voir tableau des programmes).
Panier inférieur avec casier à couverts*) Casier à couverts *) Eloignez éventuellement les supports de tasses ainsi que les supports à verres à bière existants en les plaçant à gauche.
Instructions de montage et de raccordement 1 Consignes de sécurité pour l’installateur • L’appareil doit être transporté à la verticale au risque de renverser l’eau contenant le sel spécial. • Avant la mise en service, vérifiez que le lave-vaisselle n’a pas subi de dommanges éventuels pendant le transport. Il est interdit de brancher un appareil endommagé. En cas de dommage, veuillez contacter votre concessionnaire.
Installation du lave-vaisselle • Pour être stable, le lave-vaisselle doit être placé sur un sol dur et parfaitement plat. • Pour compenser les inégalités du sol et pour mettre l’appareil à la même hauteur que les autres meubles, dégagez les pieds vissables à l’aide d’un tourne-vis. • Le tuyau de vidange, le tuyau d’alimentation d’eau et le câble d’alimentation électrique doivent avoir du jeu dans l’emboîtement du socle à l’arrière de l’appareil pour ne pas risquer d’être pliés ou compressés.
Appareils “pose libre“ (sur socle) 1 Si le lave-vaisselle est installé à proximité directe d’un four, il est nécessaire de le séparer de ce dernier à l’aide d’une plaque réfractaire à la chaleur et non inflammable (habillez la face située vers le four avec une feuille en aluminium) entre l’arête supérieure du plan de travail et le four (profondeur 57,5 cm). Pour encastrer l’appareil sous un plan de travail, vous pouvez enlever le plan de travail d’origine du lavevaisselle comme suit : 1.
Branchement du lave-vaisselle Raccordement de l’alimentation d’eau • Le lave-vaisselle peut être raccordé sur une alimentation d’eau froide et d’eau chaude jusqu’à une température max. de 60 °C. • Le lave-vaisselle ne doit pas être raccordé à des réservoirs d’eau chaude ou à des chauffe-eau. Pression de l’eau admissible Pression de l’eau minimale admissible : 1 bar (=10 N/cm2 =100 kPa) Si la pression de l’eau est inférieure à 1 bar, veuillez demander conseil à votre installateur.
Vidange de l’eau 1 Tuyau de vidange Le tuyau de vidange ne doit pas être plié, compressé ou entortillé. Raccordement du tuyau de vidange : – hauteur admissible max. : 1 mètre. – hauteur minimale admissible : 40 cm au-dessus du bord inférieur de l’appareil. Rallonges de tuyau • Vous pouvez vous procurer des rallonges de tuyau dans les magasins spécialisés ou auprès de notre service après-vente.
Vidange de l’eau dans un évier (exclusivement pour les appareils ”pose libre“) Si vous souhaitez suspendre le tuyau de vidange dans un évier, utilisez un tuyau coudé montable. Vous pouvez vous le procurer auprès du service après-vente de votre magasin vendeur en demandant la pièce portant le numéro ET 646 069 190. 1. Montez le tuyau coudé sur le tuyau de vidange. 2. Fixez le tuyau de vidange sur le bord de l’évier de telle sorte qu’il ne glisse pas.
Modalités de raccordement Les tuyaux d’alimentation et de vidange ainsi que le câble d’alimentation doivent être branchés sur l’un des côtés de l’appareil par manque place à l’arrière.
Garantie France Conformément à la Législation en vigueur, votre Vendeur est tenu, lors de l'acte d'achat de votre appareil, de vous communiquer par écrit les conditions de garantie et sa mise en œuvre appliquées sur celui-ci. Sous son entière initiative et responsabilité, votre Vendeur répondra à toutes vos questions concernant l'achat de votre appareil et les garanties qui y sont attachées. N'hésitez pas à le contacter. Electrolux Home Products France S.A.S.
9. Ne sont pas couvertes par la garantie, les défectuosités qui proviennent de réparations ou d' interventions pratiquées par des personnes non qualifiées ou incompétentes, ou qui ont pour cause l'adjonction d'accessoires ou de pièces de rechange non d'origine. 10. Les appareils aisément transportables doivent être délivrés ou envoyés au service clientèle. Les interventions à domicile ne peuvent s'entrevoir que pour des appareils volumineux ou pour des appareils encastrables. 11.
Si vous devez nous contacter France AEG Pour tenir nos engagements, nous écoutons les Consommateurs Info Conso Electrolux est le lien privilégié entre la marque et ses Consommateurs. Il assure en permanence une double mission : satisfaire au mieux vos exigences et tirer parti de cette proximité pour améliorer sans cesse les produits que nous vous proposons.
Belgique Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek E-mail: consumer.services@electrolux.be Consumer services Téléphone 02/363.04.44 Téléfax 02/363.04.00 02/363.04.60 Pièces détachées, accessoires et produits d'entretien Pour la Belgique: vous pouvez commander des pièces détachées, accessoires et consommables online à l'adresse http://www.aeg-home.
Service après-vente En cas de problèmes techniques, vérifiez d’abord s’il ne vous est pas possible de réparer vous-même le dysfonctionnement à l’aide de la notice d’utilisation (chapitre „Que faire, si...“). Si vous ne parvenez pas à réparer le dysfonctionnement, veuillez contacter notre Consumer Services. Pour pouvoir vous dépanner dans les plus brefs délais, nous nécessitons les informations suivantes : – Désignation du modèle – Numéro du produit (PNC) – Numéro de série (S-No.
From the Electrolux Group. The world´s No.1 choice. Le Groupe Electrolux est le premier fabricant mondial d'appareils de cuisine, d'entretien et d'extérieur. Plus de 55 millions de produits du Groupe Electrolux (tels que réfrigérateurs, cuisinières, lave-linge, aspirateurs, tronçonneuses, tondeuses à gazon) sont vendus chaque année pour un montant d'environ 14 milliards de dollars US dans plus de 150 pays à travers le monde. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.