32962771_EN.qxd 22/08/2008 9.
132962771_EN.qxd 22/08/2008 9.15 Page 2 2 Dear Customer Thank you for choosing one of our high-quality products. With this appliance you will experience the perfect combination of functional design and cutting edge technology. Convince yourself that our appliances are engineered to deliver the best performance and control - indeed we are setting the highest standards of excellence. In addition to this you find environmental and energy saving aspects as an integral part of our products.
132962771_EN.qxd 22/08/2008 9.
132962771_EN.qxd 4 22/08/2008 9.
132962771_EN.qxd 22/08/2008 9.15 Page 5 Contents Care and cleaning Descaling After each wash Maintenance wash External cleaning Detergent dispenser drawer Washing drum Door seal Drain pump Water inlet filter Frost precautions Emergency emptying out 5 32 32 32 32 32 32 33 33 33 35 36 36 What to do if...
132962771_EN.qxd 6 22/08/2008 9.15 Page 6 Safety information Instruction booklet Safety information Prior to using for the first time • The safety of AEG/ELECTROLUX appliances complies with the industry standards and with legal requirements on the safety of appliances. However, as manufacturers, we feel it is our duty to provide the following safety notes. You MUST read them carefully before installing or using the appliance.
132962771_EN.qxd 22/08/2008 9.15 Page 7 Safety information 7 • Wash small items such as socks, laces, washable belts etc in a washing bag or pillow case as it is possible for such items to slip down between the tub and the inner drum. • Do not use your washer-dryer to wash and dry articles with whalebones, material without hems or torn material. • Always unplug the appliance and turn off the water supply after use, clean and maintenance.
132962771_EN.qxd 8 22/08/2008 9.15 Page 8 Safety information • Before washing, ensure that all pockets are empty and buttons and zips are fastened. Avoid washing frayed or torn articles and treat stains such as paint, ink, rust, and grass before washing. Underwired bras must NOT be machine washed. • Garments which have been in contact with volatile petroleum products should not be machine washed.
132962771_EN.qxd 22/08/2008 9.15 Page 9 Safety information 9 • Keep all detergents in a safe place out of children’s reach. • Make sure that children or pets do not climb into the drum. To prevent childern or pets becoming trapped inside, machine incorporates special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin.
132962771_EN.qxd 10 22/08/2008 9.15 Page 10 Product description Product description Your new appliance meets all modern requirements for effective treatment of laundry with low water, energy and detergent consumption. The ECO valve system allows total use of detergent and reduces water consumption so saving energy.
132962771_EN.qxd 22/08/2008 9.15 Page 11 Control panel 11 Compartment for powder or liquid detergent used for main wash. Compartment for liquid additives (fabric softener, starch). Control panel Henceforth the programme selector dial, the buttons and the display will be indicated with the numbers given in this table.
132962771_EN.qxd 12 22/08/2008 9.15 Page 12 Display Display (7) 7.2 7.3 7.1 7.1 Duration of selected programme: After selecting a programme, the duration is displayed in hours and minutes (for example 2.05). The duration is calculated automatically on the basis of the maximum recommended load for each type of fabric. After the programme has started, the time remaining is updated every minute.
2962771_EN.qxd 22/08/2008 9.15 Page 13 Display 13 7.2 Delay Start (7.2) The selected delay (20 hours max) set by means of the relevant button appears on the display for about 3 seconds, then the duration of the previously selected programme is displayed. The symbol 7.2 will appear on the display. The delay time value decreases by one unit every hour. When only 1 hour remains, the time decreases every minute. 7.3 Child safety lock (7.
132962771_EN.qxd 14 22/08/2008 9.15 Page 14 Use First Use Ensure that the electrical and water connections comply with the installation instructions. Remove the polystyrene block and any material from the drum. Pour 2 litres of water into the main wash compartment of the detergent drawer in order to activate the ECO valve. Then run a cotton cycle at 90° or 95°C, without any laundry in the machine, to remove any manufacturing residue from the drum and tub.
132962771_EN.qxd 22/08/2008 9.15 Page 15 Use 15 Daily Use Load the laundry 1. Open the door by carefully pulling the door handle outwards. Place the laundry in the drum, one item at a time, shaking them out as much as possible. 2. Close firmly the door. You must hear a click during closing. Attention! Do not embed the laundry between the door and the rubber joint. Measure out the detergent and the fabric softener Your new appliance was designed to reduce water, energy and detergent consumption. 1.
132962771_EN.qxd 16 22/08/2008 9.15 Page 16 Use selector determines the type of washing cycle (e.g. water level, drum movement, number of rinses) and the washing temperature according to the type of laundry. The pilot light of button 8 starts blinking and the display shows the duration of the selected programme. The selector dial can be turned either clockwise or anticlockwise. Position O corresponds to Reset programme/Switching OFF of the machine.
132962771_EN.qxd 22/08/2008 9.15 Page 17 Use 17 STAIN option by pressing button 5 Select this option to treat heavily soiled or stained laundry with stain remover (extended main wash with time optimised stain action phase). This option is not available with a temperature lower than 40°C. Attention! If you wish to perform a programme with the stain option, pour stain remover into compartment . STAIN option is not selectable with a prewash phase.
132962771_EN.qxd 18 22/08/2008 9.15 Page 18 Use Select the DELAY START by pressing button 9 Before you start the programme, if you wish to delay the start, press button 9 repeatedly, to select the desired delay. The corresponding symbol will appear on the display. The washing programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button.
132962771_EN.qxd 22/08/2008 9.15 Page 19 Use 19 Cancelling a programme Turn the selector dial to O to cancel a programme which is running. Now you can select a new programme. Opening the door after the programme has started First set the machine to pause by pressing button 8. The door can be opened after some monutes. If the door remains locked, this means that the machine is already heating, that the water level is above the bottom edge of the door.
132962771_EN.qxd 20 22/08/2008 9.15 Page 20 Use DRYING only Do not exceed the following laundry loads: - 3 kg for linen and cottons - 2 kg for synthetics The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. Select the drying programme by turning the programme selector dial (1) Turn the programme selector dial to the required programme for Cottons or Synthetics in the Drying sector. The pilot light 10.2 illuminates.
132962771_EN.qxd 22/08/2008 9.15 Page 21 Use 21 At this point, begins an anti-crease phase which lasts for about 10 minutes. During this time the door is locked. Note! If you whish to open the door before or during the anti-crease phase or to interrupt it, press any button or turn the programme selector dial to any programme position (except «O»), the door can be immediately opened. Turn the selector dial to the «O» position to switch the machine off. Remove the laundry.
132962771_EN.qxd 22 22/08/2008 9.
132962771_EN.qxd 22/08/2008 9.15 Page 23 Washing programmes 23 Washing programmes Programme/ Temperature Type of laundry Options Description of the programme SPIN REDUCTION/ RINSE HOLD TIME (**), STAIN(*), EXTRA RINSE Main wash Rinses Short spin Max Load Kg 3 ** Red. Load Kg 1.
132962771_EN.qxd 24 22/08/2008 9.15 Page 24 Washing programmes Programme information 40 ECO EASY IRON PLUS WOOL/ SILK HANDWASH Special programme for white and coloured cotton suitable for different washing temperatures. This programme can be used for laundry, which should be washed at 40°C or 60°C separately. So, you can put into the drum the maximum load capacity in order to save energy and water. You will obtain the same good washing result as a normal programme at 60°C.
132962771_EN.qxd 22/08/2008 9.16 Page 25 Drying programmes 25 Drying programmes Degree of drying Extra dry Ideal for towelling materials Type of fabric Cotton and linen (bathrobes, bath towels, etc Cotton and linen (bathrobes, bath towels, etc Store dry (*) Suitable for items to Synthetics and mixed fabrics (jumpers, blouses, put away without underwear, household ironing linen) Iron dry Suitable for ironing Max load Spin Speed Drying time in mins 3 kg 1200 95 - 105 1.
132962771_EN.qxd 26 22/08/2008 9.16 Page 26 Preparing the wash cycle Preparing the wash cycle Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Temperatures 95° or 90° for normally soiled white cottons and linen (e.g. tea cloths, towels, tablecloths, sheets...). 60°/50° for normally soiled, colour fast garments (e.g. shirts, night dresses, pyjamas..
132962771_EN.qxd 22/08/2008 9.16 Page 27 Preparing the wash cycle 27 Maximum loads Recommended loads are indicated in the washing programme charts. General rules: Cotton, linen: drum full but not too tightly packed; Synthetics: drum no more than half full; Delicate fabrics and woollens: drum no more than one third full. Washing a maximum load makes the most efficient use of water and energy. For heavily soiled laundry, reduce the load size.
132962771_EN.qxd 28 22/08/2008 9.16 Page 28 Preparing the wash cycle already have been damaged and the fabric tends to hole. Mould stains: treat with bleach, rinse well (whites and fast coloureds only). Grass: soap lightly and treat with bleach (whites and fast coloureds only). Ball point pen and glue: moisten with acetone (*), lay the garment on a soft cloth and dab the stain. Lipstick: moisten with acetone as above, then treat stains with methylated spirits. Treat any residual marks with bleach.
132962771_EN.qxd 22/08/2008 9.16 Page 29 Preparing the wash cycle 29 Pour liquid detergent into the dispenser drawer compartment marked just before starting the programme. Any fabric softener or starching additives must be poured into the compartment marked before starting the wash programme. Follow the product manufacturers’ recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer.
132962771_EN.qxd 30 22/08/2008 9.16 Page 30 Preparing the drying cycle Preparing the drying cycle As a dryer, the machine works on the condensation principle. Therefore, the water tap must be open and the drain hose must drain water into a sink or into the drain pipe, even during the drying cycle. Maximum loads Cotton and linen 3 kg Synthetics 2 kg Attention! Before starting the drying programme, reduce the loads of washed laundry, in order to obtain good performances.
132962771_EN.qxd 22/08/2008 9.16 Page 31 Preparing the drying cycle 31 Gargment’s labels For drying, follow the indications given on the manufacturer’s labels: May be tumble dried Drying at high temperature Drying at reduced temperature Do not tumble dry.
132962771_EN.qxd 32 22/08/2008 9.16 Page 32 Care and cleaning Care and cleaning You must DISCONNECT the appliance from the electricity supply, before you can carry out any cleaning or maintenance work. Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits.
132962771_EN.qxd 22/08/2008 9.16 Page 33 Care and cleaning 33 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place. 5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6. Insert the detergent dispenser drawer in the guide rails and push it in.
132962771_EN.qxd 34 22/08/2008 9.16 Page 34 Care and cleaning 4. Place a container close to the pump to collect any spillage. 5. Release the emergency emptying hose, place it in the container and remove its cap. 6. When no more water comes out, unscrew the pump and remove it. Always keep a rag nearby to dry up spillage of water when removing the pump.
132962771_EN.qxd 22/08/2008 9.16 Page 35 Care and cleaning 35 7. Remove any objects from the pump impeller by rotating it. 8. Put the cap back on the emergency emptying hose and place the latter back in its seat. 9. Screw the pump fully in. 10. Close the pump door. Warning! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty.
132962771_EN.qxd 36 22/08/2008 9.16 Page 36 Care and cleaning Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. Close the water tap and unscrew the water inlet hose from the tap. 2. Place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out. 3. Screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again.
132962771_EN.qxd 22/08/2008 9.16 Page 37 What to do if... 37 What to do if... Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
132962771_EN.qxd 38 22/08/2008 9.16 Page 38 What to do if... Problem The machine fills then empties immediately: The machine does not empty and/or does not spin: Possible cause/Solution The end of the drain hose is too low. • Refer to relevant paragraph in «water drainage» section. The drain hose is squashed or kinked. E20 • Check the drain hose connection. The drain filter is clogged. E20 • Clean the drain filter.
132962771_EN.qxd 22/08/2008 9.16 Page 39 What to do if... Problem 39 Cause possible/Solution The door will not open: The programme is still running. • Wait the end of washing cycle. The door lock has not been released. • Wait until «0» appears on the display. There is water in the drum. • Select drain or spin programme to empty out the water. The machine vibrates or is noisy: The transit bolts and packing have not been removed. • Check the correct installation of the appliance.
132962771_EN.qxd 40 22/08/2008 9.16 Page 40 What to do if... Problem Cause possible/Solution No water is visible in the drum: Machines based on modern technology operate very economically using very little water without affecting performance. If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Mo Pro d. ..... d. No ..... . ....
132962771_EN.qxd 22/08/2008 9.16 Page 41 Consumption value 41 Water consumption (lltres) Energy consumption (KWh) Programme duration (Minutes) White Cottons 95° 61 2.0 Cottons 60° 58 1.3 (*)Cotton ECOMONY 60° 46 1.02 Cottons 40° 58 0.7 Synthetics 60° 54 1.0 Delicates 40° 60 0.55 Wool ( Handwash) 30° 53 0.25 For the duration of the programmes, please refer to the display on the control panel.
132962771_EN.qxd 42 22/08/2008 9.16 Page 42 Installation Installation Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1. After removing all the packaging, carefully lay machine on it’s back to remove the polystyrene base from the bottom. HEC0008 2.
132962771_EN.qxd 22/08/2008 9.16 Page 43 Installation 43 4. Unscrew and remove the two large rear bolts B and the six smaller bolts C. C C 5. Remove the bracket D and tighten up the six smaller bolts C. Slide out the relevant plastic spacer E. B D B E C HEC0023 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 8. Connect the water inlet hose as described under the paragraph «Water inlet».
132962771_EN.qxd 44 22/08/2008 9.16 Page 44 Installation Positioning and levelling Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Before placing it on small tiles, apply a rubber coating. Never try to correct any unevenness in the floor by HEC007S putting pieces of wood, cardboard or similar materials under the machine.
132962771_EN.qxd 22/08/2008 9.16 Page 45 Installation 45 Water drainage The end of the drain hose can be positioned in three ways: Hooked over the edge of a sink using the plastic hose guide supplied with the machine. In this case, make sure the end cannot come unhooked when the machine is emptying. This could be done by tying it to the tap with a piece of string or attaching it to the wall. In a sink drain pipe branch.
132962771_EN.qxd 46 22/08/2008 9.16 Page 46 Installation Electrical connection Information on the electrical connection is given on the rating plate on the inner edge of the appliance door. Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use. Connect the machine to an earthed socket. The manufacturer does not accept any responsibility for damage or injury through failure to comply with the above safety precaution.
132962771_EN.qxd 22/08/2008 9.16 Page 47 Environment concerns 47 Enviroment concerns Packaging materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Old machine Use authorised disposal sites for your old appliance.
132962771_EN.qxd 22/08/2008 9.16 Page 48 www.electrolux.com 132 962 771-01-342008 Subject to change without notice www.aeg-electrolux.
