LAVAMAT 14950 User manual Washer-dryer
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information Emergency emptying out What to do if… Technical data 29 29 33 Consumption values Installation instructions 33 0 Installation Unpacking Positioning and levelling 0 0 0 Water inlet Water-stop device Water drainage In the interest of the environment Electrical connection 0 0 0 0 0 Environment concerns Packaging materials Ecological hints 0 0 0 Subject to change without notice Operating instructions Safety information Read carefully & keep for future reference.
Safety information • Always unplug the appliance and turn off the water supply after use, cleaning and maintenance. • Under no circumstances should you attempt to repair the machine yourself. Repairs carried out by inexperienced people may cause injury or serious malfunctioning. Contact your local Service Centre. Always insist on genuine spare parts. Installation • This appliance is heavy. Care should be taken when moving it. • When unpacking the appliance, check that it is not damaged.
Product description 5 • Plastic detergent dispensers should not remain in the drum during the drying cycle, as the plastic used is not designed to withstand the heat. If you wish to wash-through-todry you should use the conventional detergent dispenser drawer. • Never pull the power supply cable to remove the plug from the socket; always take hold of the plug itself.
Control panel 2 1 3 4 5 6 1 2 3 4 5 6 Detergent dispenser drawer Control panel Door opening handle Rating plate Drain pump Adjustable feet Detergent dispenser drawer Compartment for prewash phase or stain remover. The prewash detergent is added at the beginning of the wash programme. The stain remover is added during the STAIN-Action phase in the main wash. Compartment for powder or liquid detergent used for main wash . Compartment for liquid additives (fabric softener, starch).
9 1 1 2 3 4 5 6 7 8 9 2 3 4 5 6 7 8 Programme selector dial SPIN reduction button AUTODRY button DRYING TIME button OPTION button OK button START/PAUSE button DELAY START button Display Symbols on the control panel = Handwash Display 9.1 9.2 9.3 9.4 9.9 9.8 9.5 9.6 9.7 9.1 - Spin Speed indicator, RINSE HOLD , NIGHT CYCLE - symbols , CUPBOARD 9.
9.3 - Programme progress indicator: PREWASH , MAIN WASH , RINSE , SPIN , OVERDOSAGE , EXTRA RINSE , DRYING , DRYING ANTI-CREASE phase symbols, The programme progress display shows the washing or drying phases of the selected programme. During a cycle, a black line blinks under the phase symbol of the running programme. At the end of each phase, the line under the corresponding symbol becomes fixed.
First use 9 First use • Ensure that the electrical and water connections comply with the installation instructions. • Remove the polystyrene block and any material from the drum. • Before the first wash, run a cotton cycle at the highest temperature without any laundry in the machine, to remove any manufacturing residue from the drum and tub. Pour 1/2 a measure of detergent into the main wash compartment and start the machine.
Daily use Washing Only Measure out the detergent and the fabric softener Your new appliance was designed to reduce water, energy and detergent consumption. 1. Pull out the dispenser drawer until it stops. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out the prewash phase or to perform the stain function, pour the detergent or the stain remover into the compartment . marked 2.
Daily use 11 If you turn the programme selector dial to another programme when the machine is working, the yellow pilot light of button 7 will blink 3 times and the message Err is displayed on the display to indicate a wrong selection. The machine will not perform the new selected programme. Select the spin speed, NIGHT CYCLE or RINSE HOLD option (button 2) When the required programme has been selected, your appliance automatically proposes the maximum spin speed provided for that programme.
Daily use After selecting the options, wait a few seconds until the display gets back to the default status. The selected options appear on the display. For the compatibility among the options and the washing programmes see chapter «Washing Programmes». PREWASH option Select this option if you wish your laundry to be prewashed at 30°C before the main wash.
Daily use 13 Select the START/PAUSE (button 7) To start the selected programme, press the button 7 , the corresponding red pilot light stops blinking. The DOOR symbol appears on the display to indicate that the appliance has started operating and the door is locked. To interrupt a programme which is running, press the button 7 : the corresponding red pilot light starts blinking. To restart the programme from the point at which it was interrupted, press the button 7 again.
Interrupting a programme Press the button 7 to interrupt a programme which is running, the corresponding light starts blinking. Press the button again to restart the programme. Cancelling a programme Turn the selector dial to a new programme. to cancel a programme which is running. Now you can select Opening the door after the programme has started When the machine is working and through the delay time, the door is locked.
Use - Drying 15 Use - Drying Drying only The recommended load size is 4 kg for cottons and linen, and 3 kg for synthetic items. By pressing Drying Time button it is also possible to dry up to 6 kg of cotton items (see the «Drying Programme » table). The water tap must be open and the drain hose must be positioned in the sink or connected to the drain pipe. 1. Load the laundry. 2. Select a spin cycle at the maximum spin speed allowed for the type of laundry in order to obtain the best drying performances.
Use - Drying During this time the ANTI-CREASE symbol appears on the display. The DOOR symbol remains lit. The door cannot be opened. If you need to open the door before or during the anti-crease phase or to interrupt it, press any button or turn the programme selector dial to any programme position (except O ), the door can be opened immediately or after a few minutes depending on the model. (In any case do not try to open the door if it is locked!) . 7.
Washing programmes 17 Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options COTTONS/LINEN 95° and 60° Main wash - Rinses - Long spin at the maximum spin speed Max. load 8 kg - Reduced load 4 kg1) White cotton (heavily or normally soiled items). SPIN REDUCTION NIGHT CYCLE RINSE HOLD PREWASH2) STAIN SENSITIVE EXTRA RINSE DAILY SUPER QUICK1) 40 - 60 MIX 40° Main wash - Rinses - Long spin at the maximum spin speed Max.
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options EASY IRON 40° Main wash - Rinses - Short spin at 1200 rpm Max. load 1,5 kg Synthetic fabrics to be gentle washed and spun. Selecting this programme the laundry is gently washed and spun to avoid any creasing. In this way ironing is easier. Furthermore the machine will perform additional rinses.
Washing programmes Programme - Maximum and Minimum Temperature - Cycle Description - Maximum Fabrics Load - Type of Laundry Options SPIN Drain and long spin at the maximum spin speed Max. load 8 kg Separate spin for hand washed cotton garments and after programmes with the option selected, which ends with water left in the tub. Before selecting this . programme the selector dial must be turned to You can choose the spin speed by pressing the relevant button to adapt it to the fabrics to be spun.
Drying Programmes Drying Programmes Automatic Programmes Degree of Drying Type of Fabric Max Load EXTRA DRY Suitable for items to put away without ironing Cotton and linen (bathrobes, bath towels, etc) 4 kg CUPBOARD DRY Suitable for items to put away without ironing Cotton and linen (bathrobes, bath towels, etc) 4 kg CUPBOARD DRY Synthetics and mixed fabSuitable for items to put away without iron- rics (jumpers, blouses, undering wear, household linen) 3 kg Cotton and linen (sheets, tableclo
Helpful hints and tips 21 Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens. Temperatures 95° or 90° for normally soiled white cottons and linen (e.g. tea cloths, towels, tablecloths, sheets...) 60°/50° for normally soiled, colour fast garments (e.g. shirts, night dresses, pyjamas....
Helpful hints and tips The following weights are indicative: pillow case, towelling towel, night dress, man’s shirt 200 g tea cloth, ladies’ briefs, napkin, blouse, men’s underpants 100 g Removing stains Stubborn stains may not be removed by just water and detergent. It is therefore advisable to treat them prior to washing. Blood: treat fresh stains with cold water. For dried stains, soak overnight in water with a special detergent then rub in the soap and water.
Drying Hints 23 Your appliance incorporates a recirculation system which allows an optimal use of the concentrated detergent. Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer . Degrees of water hardness Water hardness is classified in so-called “degrees” of hardness. Information on hardness of the water in your area can be obtained from the relevant water supply company, or from your local authority.
Care and cleaning The detergent and any additives must be placed in the appropriate compartments of the dispenser drawer before starting the wash programme. If using liquid detergents, a programme without prewash must be selected. Your appliance incorporates a re-circulation system which allows an optimal use of the concentrated detergent. Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer .
Care and cleaning 25 After each wash Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance. Keeping the door open after a wash will also help to preserve the door seal. Maintenance wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: • The drum should be empty of laundry.
Care and cleaning 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any washing to clean off any cleaning agent residues. Programme: Short Cotton Programme at maximum temperature and add approx. 1/4 measuring cup of detergent. Door seal Check from time to time the door seal and eliminate eventual possible objects that could be trapped in the fold.
Care and cleaning 6. When no more water comes out, unscrew the pump and remove it. Always keep a rag nearby to dry up spillage of water when removing the pump. 7. Remove any objects from the pump impeller by rotating it. 8. Put the cap back on the emergency emptying hose and place the latter back in its seat. 27 9. Screw the pump fully in. 10. Close the pump door. WARNING! When the appliance is in use and depending on the programme selected there can be hot water in the pump.
Care and cleaning Cleaning the water inlet filters If the appliance doesn't fill, takes long to fill water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: 1. Turn off the water tap. 2. Unscrew the hose from the tap. 3. Clean the filter in the hose with a stiff brush. 4. Screw the hose back onto the tap.
What to do if… 29 Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. close the water tap and unscrew the water inlet hose from the tap; 2. place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out; 3. screw the water inlet hose back on and reposition the emergency emptying hose after having put the cap on again.
What to do if… Problem Possible cause/Solution The washing machine does not start: The door has not been closed. • Close the door firmly. The plug is not properly inserted in the power socket. • Insert the plug into the power socket. There is no power at the socket. • Please check your domestic electrical installation. The main fuse has blown. • Replace the fuse. The selector dial is not correctly positioned and the button 7 has not been pressed.
What to do if… Problem 31 Possible cause/Solution There is water on the floor: Too much detergent or unsuitable detergent (creates too much foam) has been used. • Reduce the detergent quantity or use another one. Check whether there are any leaks from one of the inlet hose fittings. It is not always easy to see this as the water runs down the hose; check to see if it is damp. • Check the water inlet hose connection. The drain or the inlet hose is damaged. • Replace it with a new one.
What to do if… Problem Possible cause/Solution The electronic unbalance detection device has cut in because the laundry is not evenly distributed in the drum. The laundry is redistributed by reverse rotation of the drum. This may happen several times before the unbalance disapSpinning starts late or the machine does not pears and normal spinning can resume. If, after some minutes, the laundry is still not evenly spin: distributed in the drum, the machine will not spin.
Technical data 33 If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. Technical data Dimensions Width Height Depth 60 cm 82 cm 63 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door.
Installation Programme Energy consumption (KWh) Water consumption (litres) Wool/ Handwash 30° 0.32 64 Programme duration (Minutes) 1) «Cotton Energy Saving programme » at 60°C with a load of 8 kg is the reference programme for the data entered in the energy label, in compliance with EEC 92/75 standards.
Installation 2. Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance. 3. Unscrew the three bolts with the key supplied with the machine. 4. Slide out the relevant plastic spacers.
Installation 5. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal. 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 7. Connect the water inlet hose as described under the paragraph «Water inlet». Positioning and levelling Install the machine on a flat hard floor.
Installation 37 Please ensure that when the appliance is installed, it is easily accessible for the engineer in the event of a breakdown. Carefully level by screwing the adjustable feet in or out. Never place cardboard, wood or similar materials under the machine to compensate for any unevenness in the floor. Water inlet An inlet hose is supplied and can be found inside the machine drum. This appliance must be connected to a cold water supply.
Installation Water-stop device The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window «A» . Should this occur, turn the water tap off and refer to your Service Centre to replace the hose. WARNING! Installation should comply with local water authority and building regulations’ requirements.
Installation 39 When discharging into a standpipe ensure that the top of the standpipe is no more than 90 cm (35.4'') and no less than 60 cm (23.6'') above floor level. The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Force Centre. The joining piece must have an internal diameter of 18 mm. If your drain hose looks like this (see below) you do not require the “U” piece”. Just push the hose firmly in to the standpipe.
Electrical connection In the interest of the environment The appliance should be connected to the FOUL drainage system, the water will then be taken to a sewage works for treatment before being discharged safely into a river. It is essential that these appliances are not connected to the surface water drainage system as this water is discharged directly into a river or stream and may cause pollution. If you require any further advice please contact your local water authority.
for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local council, your household waste disposal service or the shop where you purchased the product.
132 953 780 - 00 - 052010 www.electrolux.