LAVAMAT L 54840 User manual Washing machine
Contents Thank you for choosing one of our high-quality products. To ensure optimal and regular performance of your appliance please read this instruction manual carefully. It will enable you to navigate all processes perfectly and most efficiently. To refer to this manual any time you need to, we recommend you to keep it in a safe place. And please pass it to any future owner of the appliance. We wish you much joy with your new appliance.
Safety information 3 Operating instructions Safety information Read carefully & keep for future reference. • The safety of Your appliance complies with the industry standards and with legal requirements on the safety of appliances. However, as manufacturers, we feel it is our duty to provide the following safety notes. • It is most important that this instruction book should be retained with the appliance for future reference.
Safety information • All packing and transit bolts must be removed before use. Serious damage can occur to the product and to property if this is not adhered to. See relevant section in the user manual. • After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall.
Product description 5 • Make sure that children or pets do not climb inside the drum. To prevent children or pets becoming trapped inside the drum the machine incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anticlockwise until the groove is vertical.
Control panel Detergent dispenser drawer Compartment for prewash phase or stain remover. The prewash detergent is added at the beginning of the wash programme. The stain remover is added during the STAIN-Action phase in the main wash. Compartment for powder or liquid detergent used for main wash . Compartment for liquid additives (fabric softener, starch). Follow the product manufacturer’s recommendations on quantities to use and do not exceed the «MAX» mark in the detergent dispenser drawer.
First use 7 Indicator pilot lights (7) After having pressed the button 5 , the FUNCTIONING pilot light ( 7.1 ) comes on. When the pilot light 7.1 comes on this means that the machine is operating. When the programme has finished, the END pilot light ( 7.2 ) comes on. When the appliance is performing additional rinses the EXTRA RINSE pilot light ( 7.3 ) comes on. To add an additional rinse, please see «Select an additional rinse».
Daily use 1. Pull out the dispenser drawer until it stops. Measure out the amount of detergent required, pour it into the main wash compartment and, if you wish to carry out the prewash phase or to perform the stain function, pour the detergent or the stain remover into the compartment . marked 2. If required, pour fabric softener into the compartment marked (the amount used must not exceed the MAX mark in the drawer). Close the drawer gently.
Daily use 9 Press the button 2 repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. The relevant light will light up. RINSE HOLD : by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing. When the programme has finished the pilot light 7.2 goes on, the pilot light of button 5 and the pilot light (7.
Daily use You must select this option after you have set the programme and before you press the button 5 . You can cancel the delay time at any moment, before you press the button 5 . If the button 5 has already been pressed: • set the washing machine to PAUSE by pressing the button 5 ; • press the button 6 once, the light relevant to the selected delay goes off; • press the button 5 again to start the programme.
After closing the door, it is necessary to select the programme and options again and to press button 5 . At the end of the programme The machine stops automatically. The pilot light of button 5 and pilot light 7.1 go off. The phase light 7.2 goes on. If a programme or an option that ends with water still in the tub has been selected, the relative pilot light remains lit, the phase light 7.2 goes on, the door remains locked to indicate that the water must be emptied out before opening the door.
Washing programmes Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options SYNTHETICS 60°- 30° Main wash - Rinses - Short spin Maximum spin speed at 1200 rpm Max. load 3 kg - Red. load 1.5 kg Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses. SPIN REDUCTION RINSE HOLD STAIN1) SUPER QUICK2) EXTRA RINSE EASY IRON 40° Main wash - Rinses - Short spin Maximum spin speed at 1200 rpm Max.
Washing programmes Programme Maximum and Minimum Temperature Cycle Description Maximum Spin Speed Maximum Fabrics Load Type of Laundry Options DRAIN Draining of water Max. load 6 kg For emptying out the water of the last rinse in programmes with the option selected, that ends with water left in the tub. Turn first the programme selector , then select programme Drain and press dial to button 5 . SPIN Drain and long spin Maximum spin speed at the maximum speed Max.
Helpful hints and tips 2) If you select the Super Quick option by pressing button 4 , we recommend that you reduce the maximum load as indicated. (Red. load = reduced load). Full loading is possible however with somewhat reduced cleaning results. Helpful hints and tips Sorting out the laundry Follow the wash code symbols on each garment label and the manufacturer’s washing instructions. Sort the laundry as follows: whites, coloureds, synthetics, delicates, woollens.
Care and cleaning 15 Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment. Although biodegradable, detergents contain substances which, in large quantities, can upset the delicate balance of nature. The choice of detergent will depend on the type of fabric (delicates, woollens, cottons, etc.), the colour, washing temperature and degree of soiling.
Care and cleaning After each wash Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance. Keeping the door open after a wash will also help to preserve the door seal. Maintenance wash With the use of low temperature washes it is possible to get a build up of residues inside the drum. We recommend that a maintenance wash be performed on a regular basis. To run a maintenance wash: • The drum should be empty of laundry.
Care and cleaning 17 1. Remove any rust deposits on the drum with a cleaning agent for stainless steel. 2. Run a washing cycle without any washing to clean off any cleaning agent residues. Programme: Short Cotton Programme at maximum temperature and add approx. 1/4 measuring cup of detergent. Door seal Check from time to time the door seal and objects that could be trapped in the fold.
Care and cleaning 7. 8. When no more water comes out, unscrew the pump cover by turning it anticlockwise and remove the filter. Use pliers, if necessary. Always keep a rag nearby to dry up any water spillages when removing the cover. Clean the filter under a tap, to remove any traces of fluff. Remove foreign bodies and fluff from the filter seat and from the pump impeller. 9. Check carefully whether the pump impeller rotates (it rotates jerkily).
Care and cleaning 19 Cleaning the water inlet filters If the appliance doesn't fill, it takes a long time to fill with water, the starting button blinks yellow or the display (if available) shows the relevant alarm (see chapter "What to do if..." for more details), check if the water inlet filters are blocked . To clean the water inlet filters: 1. Turn off the water tap. 2. Unscrew the hose from the tap. 3. Clean the filter in the hose with a stiff brush. 4. Screw the hose back onto the tap.
What to do if… Emergency emptying out If the water is not discharged, proceed as follows to empty out the machine: 1. pull out the plug from the power socket; 2. close the water tap; 3. if necessary, wait until the water has cooled down; 4. open the pump door; 5. place a bowl on the floor and place the end of the emergency emptying hose into the bowl. Remove its cap. The water should drain by gravity into the bowl. When the bowl is full, put the cap back on the hose. Empty the bowl.
What to do if… 21 • 2 flashes = «The machine does not empty and/or does not spin» , follow the corresponding suggestions in «Possible cause/Solutions» box and restart the programme. Once the problem has been eliminated, press the button 5 to restart the programme. If after all checks, the problem persists, contact your local Service Centre. Problem Possible cause/Solution The washing machine does not start: The door has not been closed. (Yellow pilot light of button 5 blinks) • Close firmly the door.
What to do if… Problem Possible cause/Solution The drain hose is squashed or kinked. (Yellow pilot light of button 5 blinks) • Check the drain hose connection. The drain filter is clogged. (Yellow pilot light of button 5 blinks) • Clean the drain filter. An option or a programme that ends with the The machine does not empty and/or does not water still in the tub or a that eliminates all the spin: spinning phases has been selected. • Select the draining or spinning programme.
Technical data Problem 23 Possible cause/Solution The door will not open: The programme is still running. • Wait the end of washing cycle. The door lock has not been released. • Wait a few minutes. There is water in the drum. • Select drain or spin programme to empty out the water. The machine vibrates is noisy: The transit bolts and packing have not been removed. • Check the correct installation of the appliance. The support feet have not been adjusted. • Check the correct levelling of the appliance.
Consumption values Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door. Water supply pressure Minimum Maximum 0,05 MPa 0,8 MPa Maximum Load Cotton 6 kg Spin Speed Maximum 1400 rpm Consumption values Programme Energy consumption (KWh) Water consumption (litres) Programme duration (Minutes) White Cottons 95° 2.0 61 135 Cottons 60° 1.3 58 125 Cotton ECO 60° 1) 1.
Installation 1. After removing all the packaging, carefully lay machine on it’s back to remove the polystyrene base from the bottom. 2. Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance. 3. Unscrew the three bolts with the key supplied with the machine.
Installation 4. Slide out the relevant plastic spacers. 5. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal. 6. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. 7. Connect the water inlet hose as described under the paragraph «Water inlet».
Installation 27 Positioning and levelling Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Before placing it on small tiles, apply a rubber coating. Never try to correct any unevenness in the floor by putting pieces of wood, cardboard or similar materials under the machine.
Installation 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. 4. Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance. The inlet hose must not be lengthened. If it is too short and you do not wish to move the tap, you will have to purchase a new, longer hose specially designed for this type of use.
Installation 29 Water drainage Place the drain hose into your standpipe, which should have an internal diameter of approximately 38 mm thus ensuring there is an air break between the drain hose and standpipe. 38 mm (11.2”) standpipe diameter 30 cm(12”) This appliance is designed to be permanently plumbed into your home's drainage system using one of the following methods. 1. Into a drainage standpipe Firstly form a hook in the end of the drain hose using the “U” piece” supplied.
Electrical connection Push the drain hose onto the spigot and secure with a clip, ensure a loop is formed in the drain hose (see diagram) to prevent waste from the sink entering the appliance. If you intend to drain the hose from the machine into a sink, make sure that the sink is empty and the plug hole is not blocked. Use the plastic “U - Piece” supplied.
Environment concerns 31 WARNING! The manufacturer does not accept any responsibility for damage or injury through failure to comply with the above safety precaution. WARNING! Should the appliance power supply cable need to be replaced, this MUST be carried out by a Service Centre. The power supply cable must be easily accessible after installing the machine. Environment concerns The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
132945810 - 00 - 162010 www.electrolux.
