LAVAMAT 6480 Waschautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programmübersicht . . . . . . . . . . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 26 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Aufstellung des Gerätes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gerät transportieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Entfernen der Transportsicherung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aufstellort.
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. • Bei Geräteanlieferung in Wintermonaten mit Minustemperaturen: Waschautomat vor Inbetriebnahme für 24 Stunden bei Raumtemperatur lagern. Bestimmungsgemäße Verwendung • Der Waschautomat ist nur zum Waschen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Waschautomaten sind nicht zulässig.
Allgemeine Sicherheit • Reparaturen am Waschautomaten dürfen nur von Fachkräften durchgeführt werden. • Den Waschautomaten niemals in Betrieb nehmen, wenn das Netzkabel beschädigt ist oder Bedienblende, Arbeitsplatte oder Sockelbereich so beschädigt sind, dass das Geräteinnere offen zugänglich ist. • Vor Reinigung, Pflege und Wartungsarbeiten den Waschautomaten ausschalten. Zusätzlich Netzstecker aus der Steckdose ziehen oder – bei Festanschluss – LS-Schalter im Sicherungskasten ausschalten bzw.
Gerätebeschreibung Bedienblende Waschmittelschublade Typschild (hinter Einfülltür) Sockelklappe/ Laugenpumpe Schraubfüße (höhenverstellbar) Bedienblende Taste Schleudern/SPÜLSTOPP Multidisplay Programmablauf-Anzeige Programmzusatz-Tasten Anzeige TÜR Programmwähler Taste START/PAUSE 7
Programmübersicht 6kg • PFLEGELEICHT 60, 50, 40, 30 3kg LEICHTBÜGELN 40 • • • • • •3) • •4) • • • • • • •4) • • 1kg • • • • • • FEINWÄSCHE 40, 30 3kg • • • • • WOLLE H(Handwäsche) 40, 30, X (kalt) 2kg • • FEINSPÜLEN 3kg • • Programm KURZ n (SPÜLSTOPP) KOCHWÄSCHE/BUNTWÄSCHE 95, 60, 50, 40, 30 1000/600 • 1400 6kg FLECKEN EXTRA SPÜLEN ENERGIESPAREN 2) Schleuderdrehzahl VORWÄSCHE max.
Anwendung/Eigenschaften Energiesparprogramm bei 60 °C für leicht bis normal verschmutzte Koch-/ Buntwäsche aus Baumwolle/Leinen. Programm für normal bis stark verschmutzte Koch-/Buntwäsche aus Baumwolle/Leinen. Programm für pflegeleichte Mischgewebe und Synthetics. Spezialprogramm bei 40 °C für pflegeleichte Textilien, die im Anschluss an dieses Programm nur noch leicht oder gar nicht gebügelt werden müssen. Schonprogramm für feine Textilien wie Schichtfasern, Mikrofasern, Synthetics, Gardinen (max.
Begriffsübersicht Die in dieser Benutzerinformation verwendeten deutschen Begriffe entsprechen nachstehenden niederländisch/französischen Bezeichnungen auf der Bedienblende Ihres Gerätes: Programmwähler 10 Tasten AUS UIT ARRET EXTRASPÜLEN SPOELEN + RINCAGE + KOCHWÄSCHE/ BUNTWÄSCHE WITTE/BONTE WAS BLANC/COULEURS KURZ KORT COURT PFLEGELEICHT KREUKHERSTELLEND SYNTHETIQUES VORWÄSCHE VOORWAS PRELAVAGE LEICHTBÜGELN STRIJKFRIJ SANS REPASSAGE FLECKEN VLEKKEN TACHES FEINWÄSCHE FIJNE WAS LINGE DEL
Vor dem ersten Waschen 1. Waschmittelschublade öffnen. 2. Etwa 2 Liter Wasser durch die Waschmittelschublade in den Waschautomaten gießen. Beim nächsten Programmstart wird dadurch der Laugenbehälter geschlossen und die ÖKO-Schleuse kann ordnungsgemäß funktionieren. 3. Um eventuelle fertigungsbedingte Rückstände aus Trommel und Laugenbehälter zu entfernen, den ersten Waschgang ohne Wäsche durchführen. Programm: KOCHWÄSCHE/BUNTWÄSCHE 95, Taste KURZ drücken, ca. 1/4 Messbecher Waschpulver zugeben.
Waschgang durchführen Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: am Griff der Einfülltür ziehen. Die Anzeigen TÜR und START/PAUSE zeigen bei eingeschaltetem Gerät an, ob die Einfülltür geöffnet werden kann: Anzeige TÜR Anzeige START/PAUSE Tür öffnen möglich? leuchtet grün blinkt rot oder ist aus ja leuchtet grün leuchtet rot ja, nach Drücken der Taste START/PAUSE leuchtet rot oder ist aus blinkt rot oder leuchtet rot nein, zu hoher Wasserstand bzw. zu hohe Temperatur 2.
1. Waschmittelschublade bis zum Anschlag herausziehen 2. Wasch-/Pflegemittel einfüllen. 3. Waschmittelschublade ganz hineinschieben. Waschpulver/Tabs für die Hauptwäsche Weichspüler/ Formspüler/ Stärke Fleckensalz/-tabs Waschpulver/Tabs für die Vorwäsche oder Wasserenthärter Waschpulver/Tabs für die Hauptwäsche Wenn Sie Wasserenthärter benutzen und das rechte Fach für Vorwaschmittel benötigen, den Wasserenthärter auf das Hauptwaschmittel in das linke Fach geben.
Schleuderdrehzahl ändern/Spülstopp wählen 3 Der Waschautomat schlägt die maximal zulässige Drehzahl vor, die für das gewählte Programm geeignet ist. Diese Drehzahl können Sie verringern: Dazu Taste Schleudern/n (SPÜLSTOPP) so oft drücken, bis die gewünschte Anzeige leuchtet. Die Drehzahl für das Endschleudern kann während des Programms noch geändert werden. Dazu: 1. Taste START/PAUSE drücken. 2. Drehzahl ändern. 3. Taste START/PAUSE erneut drücken.
VORWÄSCHE Warmes Vorwaschen vor dem automatisch folgenden Hauptwaschgang; mit Zwischenschleudern bei KOCH-/BUNTWÄSCHE und PFLEGELEICHT, ohne Zwischenschleudern bei FEINWÄSCHE. FLECKEN Für stark verschmutzte oder verfleckte Wäsche. Fleckenmittel wird zeitoptimiert während des Programmablaufs eingespült. Nur für Waschtemperaturen ab 40°C einstellbar, da Fleckenmittel erst bei höheren Temperaturen wirksam werden. Programm starten 3 1. Kontrollieren, ob der Wasserhahn geöffnet ist. 2.
Programm unterbrechen/Wäsche nachlegen Programm unterbrechen • Durch Drücken der Taste START/PAUSE kann ein Programm jederzeit unterbrochen und durch erneuten Tastendruck auf START/PAUSE wieder fortgesetzt werden. • Zum vorzeitigen Abbruch eines Programms den Programmwähler auf AUS drehen. Achtung! Wasser im Gerät beachten! Wäsche nachlegen Wäsche nachlegen ist möglich, solange die Anzeige TÜR grün leuchtet. 1. Taste START/PAUSE drücken. Einfülltür lässt sich öffnen. 2.
Kindersicherung Bei eingestellter Kindersicherung kann die Einfülltür nicht mehr geschlossen werden. Kindersicherung einstellen: Drehknopf (an der Innenseite der Einfülltür) mit einer Münze im Uhrzeigersinn bis zum Anschlag drehen. 1 Warnung! Der Drehknopf darf sich nach dem Einstellen nicht in versenkter Position befinden, sonst ist die Kindersicherung nicht aktiv! Der Drehknopf muss gemäß Abbildung herausstehen. Kindersicherung aufheben: Drehknopf entgegen dem Uhrzeigersinn bis zum Anschlag drehen.
Waschmittelschublade Die Waschmittelschublade sollte regelmäßig gereinigt werden. 1. Waschmittelschublade mit kräftigem Ruck entnehmen. 2. Weichspülereinsatz aus dem mittleren Fach herausnehmen. 3. Alle Teile mit Wasser reinigen. 4. Weichspülereinsatz bis zum Anschlag aufstecken, so dass er fest sitzt. 5. Gesamten Einspülbereich des Waschautomaten, besonders auch die Düsen an der Oberseite der Einspülkammer, mit einer Bürste reinigen. 6. Waschmittelschublade in Führungsschienen einsetzen und einschieben.
Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs einer der folgenden Fehlercodes im Multidisplay angezeigt wird: – E10 (Probleme mit Wasserzulauf), – E20 (Probleme mit Wasserablauf), – E40 (Einfülltür offen), sehen Sie bitte in nachfolgender Tabelle nach. Nachdem der Fehler behoben ist, Taste START/PAUSE drücken. Bei anderen Fehlern (E und Zahl oder Buchstabe): Gerät aus- und wieder einschalten. Programm neu einstellen. Taste START/PAUSE drücken.
Problem Waschautomat vibriert während des Betriebs oder steht unruhig. Wäsche ist nicht geschleudert. Mögliche Ursache Transportsicherung nicht entfernt. Transportsicherung entfernen. Schraubfüße nicht korrekt eingestellt. Füße laut Aufstell- und Anschlussanweisung justieren. Trommel immer möglichst Nur wenige, große Wäschevoll beladen. Große und kleistücke in der Trommel. ne Teile mischen. Verschraubung am Zulaufschlauch undicht. Zulaufschlauch festschrauben. Ablaufschlauch undicht.
Problem Mögliche Ursache Einfülltür verriegelt. Einfülltür lässt sich bei eingeschaltetem Gerät nicht öffnen. Wäsche stark verknittert. Abhilfe Warten, bis Anzeige TÜR grün leuchtet. Programm läuft weiter, wenn Stromausfall vorüber ist. Stromausfall! (Alle Anzeigen sind aus.) Einfülltür bleibt ca. 4 bis 10 Minuten verriegelt. Zum Wäsche entnehmen: Ist Wasser im Gerät zu sehen, vor Öffnen der Einfülltür erst das Wasser ablassen (siehe Abschnitt „Notentleerung durchführen“).
Notentleerung durchführen 1 Warnung! Waschautomat vor Notentleerung ausschalten und den Netzstecker aus der Steckdose ziehen! Warnung! Die Waschlauge, die aus dem Notentleerungsschlauch ausläuft, kann heiß sein. Verbrühungsgefahr! Vor einer Notentleerung Waschlauge abkühlen lassen! 1. Sockelklappe aufklappen und abziehen. 2. Notentleerungsschlauch herausnehmen. 3. Flaches Auffanggefäß unterstellen. Anschließend Verschlussstopfen durch Drehen gegen den Uhrzeigersinn lösen und herausziehen. 4.
Laugenpumpe 1 Die Laugenpumpe ist wartungsfrei. Das Öffnen des Pumpendeckels ist nur im Störungsfall erforderlich, wenn kein Wasser mehr abgepumpt wird, z. B. bei blockiertem Pumpenrad. Bitte vor dem Einfüllen der Wäsche immer sicherstellen, dass sich keine Fremdkörper in den Taschen oder zwischen der Wäsche befinden. Büroklammern, Nägel etc., die eventuell mit der Wäsche in den Waschautomaten gelangt sind, bleiben im Pumpengehäuse (Fremdkörperfalle, die das Pumpenrad schützt) liegen.
Entsorgung 2 2 1 24 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 850 x 598 x 603mm Tiefe bei geöffneter Einfülltür 980 mm Höhenverstellbarkeit ca. +10/-5mm Füllmenge (programmabhängig) max.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Dieser Waschautomat ist nicht unterbaufähig. • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann es beim Schleudern zu Schäden am Gerät oder an benachbarten Möbeln kommen.
• Gerät niemals ohne Transportsicherung transportieren. Transportsicherung erst am Aufstellort entfernen! Transport ohne Transportsicherung kann zu Schäden am Gerät führen. • Das Gerät nicht an der geöffneten Einfülltür und auch nicht am Sockel anheben. Bei Transport mit der Sackkarre: • Sackkarre nur seitlich ansetzen. Entfernen der Transportsicherung 1 Vor der Installation müssen Sie die Transportsicherungen entfernen. Gehen Sie wie folgt vor: 1.
3. Schrauben Sie mit einem Schlüssel, der dem Gerät beiliegt, die zentrale Schraube A an der Rückwand des Waschautomatens heraus. Ziehen Sie den Plastikzapfen heraus. 4. Schrauben Sie die zwei großen Schrauben B und die sechs kleineren seitlichen Schrauben C an der Rückwand des Waschautomaten heraus. 5. Ziehen Sie die Stahlschiene D ab. 6. Schrauben Sie die sechs kleineren seitlichen Schrauben C wieder auf.
7. Öffnen Sie die Tür und entnehmen Sie den Zulaufschlauch aus der Trommel. Entfernen Sie den mit dem Klebeband fixierten Polystyrolblock aus der Türdichtung. 8. Verschließen Sie die kleinere obere Öffnung und die zwei größeren seitlichen Öffnungen mit den Kunststoffabdeckungen, die dem Gerät beiliegen. Hinweis: Wir empfehlen, die Transportsicherungsteile aufzubewahren, um sie bei Umzug wieder verwenden zu können. Gerät niemals ohne Transportsicherung transportieren.
Gerät ausrichten Die vier Füße des Gerätes sind voreingestellt. Grobe Unebenheiten können durch individuelles Einstellen der höhenverstellbaren Schraubfüße ausgeglichen werden. Dazu den beiliegenden Spezialschlüssel verwenden. Achtung! Unebenheiten des Bodens nicht durch Unterlegen von Holz, Pappe oder ähnlichem ausgleichen, sondern durch Einstellen der höhenverstellbaren Schraubfüße.
Wasseranschluss Achtung! • Ein Zulaufschlauch wird mitgeliefert und befindet sich im Inneren der Trommel. • Verwenden Sie für den Wasseranschluss nicht den Schlauch von Ihrer bisherigen Maschine. • Dieses Gerät darf nicht an Warmwasser angeschlossen werden! 1. Öffnen Sie die Tür und ziehen Sie den Zulaufschlauch heraus. 2. Schließen Sie den Schlauch mit dem Winkelverbindungsstück an die Maschine an. Wichtig! Richten Sie den Zulaufschlauch nicht nach unten.
Wasserablauf Der Höhenunterschied zwischen Standfläche und Wasserabfluss darf höchstens 1 Meter betragen. Zur Verlängerung dürfen nur Originalschläuche verwendet werden. (Max. 3 m auf dem Fußboden verlegt und dann bis 80 cm hoch). Der Kundendienst führt Ablaufschläuche in verschiedenen Längen. Wasserablauf in einen Siphon Die Verbindungsstelle Tülle/Siphon mit einer Schlauchschelle (im Fachhandel erhältlich) sichern. 1 Wasserablauf in ein Waschbecken/Badewanne Achtung! – Kleine Becken sind nicht geeignet.
Garantie/Kundendienst Belgien Unsere Geräte werden mit größter Sorgfalt hergestellt. Trotzdem kann es einmal zu einem Defekt kommen. Unser Kundendienst übernimmt auf Anfrage gerne die Reparatur, und zwar sowohl während des Garantiezeitraums als auch danach. So ist gewährleistet, dass ein Defekt nicht zu einer Verkürzung der Lebensdauer des Geräts führt. Die vorliegenden Garantiebedingungen beruhen auf der Richtlinie der Europäischen Union 99/44/EG sowie den Bestimmungen des Bürgerlichen Gesetzbuches.
11.Bei Einbau- oder Unterbaugeräten sowie bei Geräten, die derart befestigt oder aufgehängt sind, dass für den Aus- und Wiedereinbau in die betreffende Einbaunische mehr als eine halbe Stunde erforderlich ist, werden die anfallenden Zusatzleistungen in Rechnung gestellt. Etwaige Schäden infolge derartiger Aus- und Wiedereinbauarbeiten gehen zu Lasten des Kunden. 12.
Europäische Garantie Für dieses Gerät besteht in den am Ende dieser Benutzerinformation aufgeführten Ländern eine Garantie von Electrolux für den Zeitraum, der in der Gerätegarantie oder andernfalls gesetzlich festgelegt ist. Wenn Sie aus einem dieser Länder in ein anderes der aufgeführten Länder ziehen, wird die Gerätegarantie unter folgenden Voraussetzungen mit übertragen: • Die Gerätegarantie beginnt an dem Datum, an dem Sie das Gerät gekauft haben.
www.electrolux.com 36 p t b Albania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 Tirane Belgique/België/ Belgien +32 2 363 04 44 Bergensesteenweg 719, 1502 Lembeek Èeská republika +420 2 61 12 61 12 Budìjovická 3, Praha 4, 140 21 Danmark +45 70 11 74 00 Sjællandsgade 2, 7000 Fredericia Deutschland +49 180 32 26 622 Muggenhofer Str. 135, 90429 Nürnberg Eesti +37 2 66 50 030 Mustamäe tee 24, 10621 Tallinn España +34 902 11 63 88 Carretera M-300, Km.
p t b Slovenija +38 61 24 25 731 Electrolux Ljubljana d.o.o. Gerbiceva 98, 1000 Ljubljana Slovensko +421 2 43 33 43 22 Electrolux Slovakia s.r.o., Electrolux Domáce spotrebièe SK, Seberíniho 1, 821 03 Bratislava Suomi www.electrolux.
Service Bei technischen Störungen prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können. Wenn Sie das Problem nicht beheben konnten, wenden Sie sich bitte an den Kundendienst oder einen unserer Service-Partner. Um Ihnen schnell helfen zu können, benötigen wir folgende Angaben: – Modellbezeichnung – Produkt-Nummer (PNC) – Serien-Nummer (S-No.
www.electrolux.com www.aeg-electrolux.de www.aeg-electrolux.at www.aeg-electrolux.be www.aeg-electrolux.lu www.aeg.