LAVAMAT 74800 Washing machine User information
Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programme overview . . . . . . . . . . . . . . . . . .
Installation and connection instructions. . . . . . . . . . . . . . . . . 26 Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Unpacking. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. • If the appliance is delivered in the winter months when there are minus temperatures: Store the washing machine at room temperature for 24 hours before using for the first time. Correct use • The washing machine is only designed for the washing of normal domestic laundry at home. • Additions or modifications to the washing machine are not permitted.
General safety • Repairs to the washing machine must only be carried out by qualified service engineers. • Never use the washing machine if the mains cable is damaged; or if the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • Switch off the washing machine before cleaning, maintenance and servicing.
Description of the appliance Detergent dispenser drawer Control panel Rating plate (behind door) Plinth flap/ Drain pump Screw feet (height adjustable) Control panel SPIN/RINSE HOLD button Multi-display DELAY TIMER button Programme option buttons START/PAUSE button Programme progress display DOOR indicator Programme knob OVERDOSING indicator 7
Programme overview STAIN SENSITIVE 1400 1000/700/500 RINSE HOLD • • • • •4) • • • • • • • • • • • • •4) • • • • • • • • • • • • • • 2kg • • 3,5kg • • 7kg • COTTONS/LINEN 95, 60, 40, 30 7kg • 40-60 MIX 7kg • EASY-CARES 60, 50, 40, 30 3,5kg • EASY IRON 40 1kg 3,5kg DELICATES 40, 30 WOOL/SILK H (Hand-washing) 40, 30, COLD RINSE TIME SAVER • RINSE + • max.
Application/Features Energy-saving programme which washes at 60 °C for lightly to normally soiled whites or coloureds made of cotton/linen. Programme for normally to heavily soiled whites/coloureds made of cotton/linen. Programme for cottons/linen, which is indicated for various wash temperatures. Items which according to their care label are normally washed separately at 40 °C or at 60 °C, can be washed together in this programme. In this way the drum capacity is better used, saving energy.
Before the first wash 1. Open the detergent drawer. 2. Pour approx. 2 litres of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly 3. To remove any production-related residues from the drum and water tank, perform the first wash cycle without a load. Programme: COTTONS/LINEN 95, press the TIME SAVER button, add approx. 1/4 measuring cup of detergent.
Running a washing cycle Opening the door/loading washing 1. To open the door: pull the door by the handle. When the machine is switched on, the DOOR light and the START/ PAUSE light indicate whether the door can be opened: DOOR indicator START/PAUSE indicator Can the door be opened? lit green flashes red or is off yes lit green lit red yes, after the START/PAUSE button has been pressed lit red or is off flashes red or lit red no, water level and/or temperature too high 2.
Dosing depends upon: – the washing’s degree of soiling, – the size of the load – the degree of hardness of the water supply. • If the manufacturer does not give instructions for small loads: for a half load, use a third less, for a very small load, use only half of the detergent that is recommended for a full load. • From water hardness 2 (= medium) upwards, water softener should be used. Detergent can then always be dosed for water hardness 1 (= soft).
Switching on the appliance/selecting a programme 3 Set the programme and temperature using the programme knob. By selecting a programme, you switch the appliance on at the same time. – The programme progress display indicates the programme steps that the selected programme will perform. – In the multi-display the estimated length of the programme (in minutes) appears.
Selecting the programme options 3 If desired, press the programme option button(s). The corresponding light lights up. If “Err” flashes in the multi-display, the programme option selected cannot be combined with the wash programme set. RINSE + Two additional rinse cycles are carried out for the programmes ENERGY SAVING, COTTONS/LINEN, DELICATES, EASY-CARES and EASY IRON (e. g. in cases of over-sensitive skin). TIME SAVER Shortened wash cycle for lightly soiled washing.
Setting the delay timer 3 3 With the DELAY TIMER button you can postpone the start of a programme by 30 minutes (30') to a maximum of 23 hours (23h). 1. Select programme. 2. Continue pressing the DELAY TIMER button until the desired start delay is displayed in the multi-display, for example12h, if the start of the programme is to be delayed by 12 hours. DELAY TIMER light is lit. If the display is showing 23h and you press the button again, the time delay will be cancelled.
Interrupting a programme/adding washing Interrupting a programme • A washing programme can be interrupted at any time by pressing the START/PAUSE button. It is then re-started by pressing the START/ PAUSE button again. • To stop the washing machine before the programme has ended, turn the programme knob to OFF. Important! Be careful if there is water in the appliance! Adding washing It is possible to add washing, as long as the DOOR light is lit green. 1. Press the START/PAUSE button.
Child safety device When the child safety device is set, the door can no longer be closed. Setting the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go. 1 Warning! The knob must not be sunk-in after being set, otherwise the child safety device is not active. The knob must stand out as shown in the illustration. Releasing the child safety device: Turn the knob anti-clockwise as far as it will go.
Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place. 5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6.
What to do if... Remedying small malfunctions If one of the following fault codes is displayed in the multi-display during operation: – E10 (Problems with water inlet), – E20 (Problems with water drainage), – E40 (door open), please have a look at the following table. When the fault is remedied, press the START/PAUSE button. In the event of other faults (E plus a number or a letter): Switch the appliance off and on again. Re-set the programme. Press the START/ PAUSE button.
Problem Washing machine vibrates when operating or is noisy. Washing has not been spun. Possible cause Transport lock has not been removed. Remedy Remove transport lock. Adjust feet according to the Screw feet not correctly adInstallation and Connection justed. instructions. Only a few large items of washing in the drum. Always load the drum as full as possible. Mix large and small items. Screw connection on the inTighten inlet hose. let hose is leaking. Drain hose is leaking.
Problem Possible cause Door locked. Door cannot be opened Power cut. (All display indiwhen appliance is cators are off.) switched on. Door remains locked for 4 to 10 minutes. Washing is heavily creased. Possibly too much washing was loaded. Remedy Wait until DOOR indicator is lit green. Programme continues, when power cut is over. To remove washing: If water can be seen in the appliance, before opening the door, first drain off the water. (See section “Carrying out an emergency drain”.
Carrying out an emergency drain 1 Warning! Before emergency draining, switch off the washing machine and remove the mains plug from the socket. Warning! The water that comes out of the emergency drain hose may be hot. There is a risk of scalding. Let the water cool before performing an emergency drain. 1. Open the plinth flap and remove it. 2. Take out the emergency drain hose. 3. Place a shallow container underneath it.
Drain pump 1 The drain pump is maintenance-free. It is only necessary to open the pump cover if there is a malfunction and water is no longer being pumped out, e. g. if the pump wheel is blocked. Please make sure before loading the washing that there are no foreign bodies in the pockets or caught between the washing. Paperclips, nails, etc. that may have got into the washing machine with the washing remain in the pump housing (foreign body trap that protects the pump wheel).
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W 1 24 The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x Width x Depth 850 x 598 x 640 mm Depth when door is open 1017 mm Height adjustment approx. +10/-5mm Load (depending on programme) Max.
Installation and connection instructions 1 Safety information for the installation • This washing machine cannot be built-in. • Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. • Before using for the first time, all parts of the transport lock must be removed.
• Never transport the appliance without its transport lock. Only remove the transport lock when the appliance is in its place of installation. Transporting the appliance without its transport lock can lead to damage to the appliance. • Never lift the appliance by the door when it is open nor by the plinth. When moving using a sack trolley: • Only use the sack trolley on the side of the appliance. Unpacking 1 The transport safeguard must be removed before putting the appliance into operation.
3. With a suitable spanner unscrew and remove the central rear bolt A. Slide out the relevant plastic spacer. 4. Unscrew and remove the two large rear bolts B and the six smaller bolts C. 5. Remove the bracket D. 6. Tighten up the six smaller bolts C.
7. Open the porthole and remove the polystyrene block fitted with the adhesive tape on the door seal. 8. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Important! All the different plug caps are supplied with the appliance in the plastic bag containing the instruction booklet. Connect the water inlet hose as described under the paragraph “Water inlet”.
Making the appliance level The four feet of the appliance are pre-adjusted. Large degrees of unevenness can be compensated for by individually adjusting the height adjustable screw feet. Use the special spanner supplied to do this. Important! Do not use pieces of wood, cardboard or such like to level out unevenness in the floor, but adjust the height adjustable screw feet instead. Electrical connection Details about the voltage, type of supply and the fuses required are to be found on the rating plate.
Water inlet Attention! • An inlet hose is supplied and can been found inside the machine drum. • Do not use the hose from your previous machine to connect to the water supply. • This appliance must not be connected to the hot water system. 1. Open the porthole and extract the inlet hose. 2. Connect the hose with the angled connection to the machine. Important! Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. 3.
Water drainage The maximum permitted difference between the height of the surface on which the appliance is installed and the water outlet is 1 metre. Only original hoses may be used to extend hoses. (A maximum of 3 m laid on the floor and then 80 cm vertically). The Customer Care Department stocks outlet hoses of different lengths. Draining water into a sink outlet Secure the outlet/sink outlet joint with a hose band clip (available from your dealer).
Guarantee/Customer Service European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
p t b Lietuva +370 5 2780609 Verkių 29, LT 09108 Vilnius Luxembourg +35 2 42 43 13 01 Rue de Bitbourg, 7, L-1273 Hamm Magyarország +36 1 252 1773 H-1142 Budapest XIV, Erzsébet királyné útja 87 Nederland +31 17 24 68 300 Vennootsweg 1, 2404 CG Alphen aan den Rijn Norge +47 81 5 30 222 Risløkkvn. 2 , 0508 Oslo Österreich +43 18 66 400 Herziggasse 9, 1230 Wien Polska +48 22 43 47 300 ul.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
www.electrolux.