L 70470 FL L 70670 FL WASHING MACHINE USER MANUAL
CONTENTS 4 6 6 7 7 8 12 15 15 15 16 17 18 20 22 27 30 SAFETY INFORMATION ENVIRONMENT CONCERNS TECHNICAL INFORMATION PRODUCT DESCRIPTION ACCESSORIES CONTROL PANEL PROGRAMMES BEFORE FIRST USE USING THE APPLIANCE LOADING THE LAUNDRY FILLING THE DETERGENT AND ADDITIVES SETTING AND STARTING A PROGRAMME AT THE END OF THE PROGRAMME HELPFUL HINTS AND TIPS CARE AND CLEANING TROUBLESHOOTING INSTALLATION SERVICE When contacting Service, ensure that you have the following data available.
ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage.
ENGLISH • • • • • • internal components and cause leakages or malfunctions. Do not install and connect a damaged appliance. Make sure to remove all packaging and transport bolts. Make sure that the mains plug is disconnected from the mains socket during installation. Only a qualified person must do the electrical installation, the plumbing and the installation of the appliance. This to prevent the risks of structural damage or injury.
ENVIRONMENT CONCERNS PACKAGING MATERIALS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. ECOLOGICAL HINTS To help the environment, use less water and energy, obey these instructions: • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry. • If necessary, use a stain remover when you set a programme with a low temperature.
ENGLISH PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 12 7 1 Worktop 2 Detergent dispenser 7 Feet for the appliance level 8 Water drain hose 3 Control panel 4 Door handle 9 Water inlet valve 10 Mains cable 5 Rating plate 6 Drain pump 11 Transit bolts 12 Feet for the appliance level ACCESSORIES 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts.
CONTROL PANEL 1 2 3 Damp Krøludglatning Damp Genopfriskning Koge-/Kulørt + Forvask Energispare Ekstra Stille Super Eco Syntetisk 20 Min. - 3 kg Strygelet Finvask Jeans Skyl Centr./ Tømning Uld/Silke Centrif. Pletter Ekstra Skyl Spar Tid Udskudt Start 9 8 7 6 5 Tæpper On/Off Temp.
ENGLISH B • The default spin speed of the programme. • 'No Spin'1) and 'Rinse Hold' symbols. C • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the appliance door when the symbol is on. You cannot open the appliance door when the symbol flashes. Wait for some minutes before you open the door. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum.
TIME SAVE BUTTON 6 Press the button 6 to decrease the programme duration. • Press one time to set 'Shortened duration' for items with daily soil. • Press two times to set 'Extra Quick' for items with almost no soil. Some programmes accept only one of the two functions. EXTRA RINSE BUTTON 7 Press button 7 to add rinsing phases to a programme. Use this function for persons allergic to detergents and in areas where the water is soft. STAIN BUTTON 8 Press button 8 to add the stain phase to a programme.
ENGLISH PERMANENT EXTRA RINSE FUNCTION With this function you can keep the extra rinse function permanently on when you set a new programme. • To activate the function press button 6 and button 5 at the same time until the indicator of button 7 is on. 11 • To deactivate the function press button 6 and button 5 at the same time until the indicator of button 7 is off.
PROGRAMMES Programme Temperature Type of load max. weight of load Cycle description Functions Koge-/Kulørt 95° - Cold White and coloured cotton with normal soil. max. 7 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD PLETTER EKSTRA SKYL SPAR TID1) Koge-/Kulørt + Forvask 95° - Cold White and coloured cotton with heavy soil. max. 7 kg Prewash Wash Rinses Long spin SPIN REDUCTION RINSE HOLD EKSTRA SKYL SPAR TID1) Ekstra Stille 95° - Cold White and coloured cotton with normal soil. max.
ENGLISH 13 Programme Temperature Type of load max. weight of load Cycle description Functions Skyl Hand washed items. Rinses Long spin SPIN REDUCTION RINSE HOLD EKSTRA SKYL Gardiner 40° - Cold Set this programme to wash curtains. It adds automatically the prewash phase to clean the dust from the curtains. Do not put the detergent into the prewash compartment. max. 2 kg Prewash Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EKSTRA SKYL4) Jeans 60° - Cold All items in jeans.
5) Set this programme to decrease the time and the consumption of energy and water. 6) Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. CONSUMPTION VALUES Programme1) Energy consumption (KWh)2) Water consumption (litre)2) White Cottons 95 °C 2.3 66 Cottons 60 °C 1.3 62 Cottons 40 °C 0.8 62 Synthetics 40 °C 0.53 45 Delicates 40 °C 0.57 53 Wool/ Handwash 30 °C 0.
ENGLISH 15 BEFORE FIRST USE 1. To activate the drain system, put 2 litre of water in the main wash compartment of the detergent dispenser. 2. Put a small quantity of detergent in the main wash compartment of the detergent dispenser. Set and start a programme for cotton at the highest temperature without laundry. This removes all possible dirt from the drum and the tub. USING THE APPLIANCE 1. Open the water tap. 2. Connect the mains plug to the mains socket. 3. Press button 1 to activate the appliance.
FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase, the soak programme and for the stain function. Add the detergent for prewash, soak and stain remover before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
ENGLISH 17 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser.
CHANGE A FUNCTION You can change only some functions before they operate. 1. Press button 4 . The indicator flashes. 2. Change the function set. SET THE DELAY START 1. Press button 5 again and again until the display shows the number of minutes or hours. The related symbols comes on. 2. Press button 4 , the appliance starts the countdown of the delay start. When the countdown is completed, the programme starts automatically.
ENGLISH To drain the water: 1. If necessary, decrease the spin speed. 2. Press the Start/Pause button 4 . The appliance drain the water and spin. 3. When the programme is completed and the door lock symbol goes off, you can open the door 19 4. Deactivate the appliance. The appliance drain and spin automatically after approximately 18 hours.
HELPFUL HINTS AND TIPS THE LAUNDRY LOAD DETERGENTS AND ADDITIVES • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and coloured items. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty the pockets and unfold the items.
ENGLISH Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.
CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. DESCALING The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines. Obey the instructions that you find on the packaging of the manufacturer. Do this separately from the laundry wash. EXTERNAL CLEANING CAUTION! Do not use alcohol, solvents or chemical products.
ENGLISH 23 DETERGENT DISPENSER To clean the dispenser: 1 1. Press the lever. 2. Pull the dispenser out. 2 3. 4. 5. 6. DRAIN PUMP Regularly examine the drain pump and make sure that it is clean. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The display shows an alarm code because of the problem with water drain. Remove the top part of the liquid additive compartment.
To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. 4. 1 5. 6. 2 When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
ENGLISH 25 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 2 1 THE INLET HOSE FILTER AND THE VALVE FILTER It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button 4 flashes and the display shows the related alarm.
When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. FROST PRECAUTIONS If the appliance is installed in an area where the temperature can be less than 0 °C, remove the remaining water from the inlet hose and the drain pump. 1. Disconnect the mains plug from the mains socket. 2. Close the water tap. 3.
ENGLISH 27 TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. WARNING! Deactivate the appliance before you do the checks.
Problem Possible cause Possible solution The spin phase does not operate. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse.
ENGLISH Problem Possible cause Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre.
INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
ENGLISH 31 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers.
12. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. POSITIONING AND LEVELLING • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
ENGLISH 33 THE INLET HOSE • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 35 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose.
With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose.
ENGLISH You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension.
www.aeg.