LAVAMAT 74953 M3 EN WASHING MACHINE USER MANUAL
FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
Contents 3 CONTENTS 4 6 7 9 9 10 16 20 22 28 31 31 32 37 37 Safety information Product description Control panel First use Personalization Daily use Washing programmes Helpful hints and tips Care and cleaning What to do if… Technical data Consumption values Installation Electrical connection Environment concerns The following symbols are used in this user manual: Important information concerning your personal safety and information on how to avoid damaging the appliance.
Safety information SAFETY INFORMATION Read carefully & keep for future reference. • The safety of Your appliance complies with the industry standards and with legal requirements on the safety of appliances. However, as manufacturers, we feel it is our duty to provide the following safety notes. • It is most important that this instruction book should be retained with the appliance for future reference.
Safety information 5 • After having installed the appliance, check that it is not standing on the inlet and drain hose and the worktop is not pressing the electrical supply cable against the wall. • If the machine is situated on a carpeted floor, please adjust the feet in order to allow air to circulate freely under the appliance. • Always be sure, that there is no water leakage from hoses and their connections after the installation.
Product description • Make sure that children or pets do not climb inside the drum. To prevent children or pets becoming trapped inside the drum the machine incorporates a special feature. To activate this device, rotate the button (without pressing it) inside the door clockwise until the groove is horizontal. If necessary use a coin. To disable this device and restore the possibility of closing the door, rotate the button anticlockwise until the groove is vertical.
Control panel 7 Detergent dispenser drawer Compartment for detergent used for prewash. The prewash detergent is added at the beginning of the wash programme. Compartment for powder or liquid detergent used for main wash. Compartment for liquid additives (fabric softener, starch). Compartment for stain remover used for main wash with STAIN-option. CONTROL PANEL Below is a picture of the control panel. It shows the programme selector dial as well as the buttons and the display.
3 4 5 6 7 8 9 SPIN reduction button (GIRI/MIN) OPTION button (OPZIONI) OK button (OK) TIME SAVING button (RISPARMIO TEMPO) START/PAUSE button (AVVIO/PAUSA) DELAY START button (PARTENZA RITARDATA) Display Symbols on the control panel = Handwash = Child Lock Display 9.1 9.2 9.3 9.4 9.9 9.5 9.6 9.7 9.8 9.1 - Temperature indicator and COLD symbol 9.2 - Spin Speed indicator, RINSE HOLD , NIGHT CYCLE - symbols , SPIN , 9.
First use 9 – After selecting a programme, the duration is displayed in hours and minutes (for ex. The duration is calculated automatically on the basis of the maximum ample recommended load for each type of fabric. – After the programme has started, the time remaining is updated every minute. • Delay start – The selected delay (20 hours max) set by means of the relevant button appears on the ), then the duration of the previously display for about 3 seconds (for example selected programme is displayed.
Daily use Child safety lock This device permits you to leave the appliance unattended and not to worry that children might be injured by or cause damage to the appliance. This function remains able also when the washing machine is not working. To enable (or disable) this option press simultaneously for about 6 seconds buttons 4 and 5 until the Child Lock symbol appears on (or disappears from) the display.
Daily use 11 2. If required, pour fabric softener into the compartment marked (the amount used must not exceed the MAX mark in the drawer). Close the drawer gently. Turn the programme dial (1) to set the required programme You can choose the right programme for any type of laundry following the descriptions on the washing programme tables (see «Washing Programmes» ). Turn the programme dial to the required programme. The programme dial determines the type of washing cycle (e.g.
Daily use Select the spin speed, NIGHT CYCLE or RINSE HOLD option (button 3) When the required programme has been selected, your appliance automatically proposes the maximum spin speed provided for that programme. Press this button repeatedly to change the spin speed, if you want your laundry to be spun at a speed different from the one proposed by the washing machine. RINSE HOLD: by selecting this option the water of the last rinse is not emptied out to prevent the fabrics from creasing.
Daily use 13 This option is recommended for heavily soiled laundry. STAIN option Select this option to treat heavily soiled or stained laundry with stain remover (extended main wash with time optimized stain action phase). The relevant symbol will appear on the display. This option is not available with a temperature lower than 40°C. If you wish to perform a programme with the stain option, pour stain remover into stain compartment marked with an arrow.
Daily use Select the DELAY START (button 8) Before you start the programme, if you wish to delay the start, press the button repeatedly, to select the desired delay. The corresponding symbol will appear on the display. The wash programme can be delayed from 30 min - 60 min - 90 min, 2 hours and then by 1 hour up to a maximum of 20 hours by means of this button. The selected delay time value will appear on the display for about 3 seconds, then the duration of the programme will appear again.
Opening the door after the programme has started When the machine is working and throughout the delay time the door is locked. If, for any reason, you wish to open the door, set firstly the machine to pause by pressing the button 7. • If the DOOR symbol disappears, the door can be opened; • If the DOOR symbol doesn’t go off, it means that the machine is already heating or that the water level is too high.
Washing programmes WASHING PROGRAMMES Programme — Maximum and Minimum Temperature — Cycle Description — Maximum Fabrics Load — Type of Laundry COTONI 95°- Cold Main wash - Rinses - Long spin Max. load 8 kg - Reduced load 4 kg For white and coloured cotton (normally soiled items). Options SPIN REDUCTION / NIGHT CYCLE / RINSE HOLD PREWASH1) STAIN2) SENSITIVE EXTRA RINSE TIME SAVING3) IGIENE 60° Main wash - Rinses - Long spin Max. load 8 kg Washing programme for white cottons.
Washing programmes Programme — Maximum and Minimum Temperature — Cycle Description — Maximum Fabrics Load — Type of Laundry SINTETICI 60°- Cold Main wash - Rinses - Short spin Max. load 4 kg - Reduced load 2 kg Synthetic or mixed fabrics: underwear, coloured garments, non-shrink shirts, blouses. FACILE STIRO PLUS 60°- Cold Main wash - Rinses - Short spin Max. load 1.5 kg Synthetic fabrics to be gentle washed and spun. Selecting this programme the laundry is gently washed and spun to avoid any creasing.
Washing programmes Programme — Maximum and Minimum Temperature — Cycle Description — Maximum Fabrics Load — Type of Laundry Options CENTRIFUGA Drain and long spin Max. load 8 kg Separate spin for hand washed cotton garments and after programmes with the Rinse Hold or Night Cycle option selected. Before selecting this programme the . You can choose selector dial must be turned to the spin speed by pressing the relevant button to adapt it to the fabrics to be spun.
Washing programmes Programme — Maximum and Minimum Temperature — Cycle Description — Maximum Fabrics Load — Type of Laundry Options SPORT 40° - Cold Prewash - Main wash - Rinses - Short spin Max. load 3 kg Special programme is suitable for washing heavily soiled sport items. The machine will add automatically a prewash phase before the main wash to eliminate mud stains. We recommend you NOT to put the compartment of the detergent detergent into the drawer.
Helpful hints and tips Programme — Maximum and Minimum Temperature — Cycle Description — Maximum Fabrics Load — Type of Laundry RISPARMIO ENERGIA 60° Main wash - Rinses - Long spin Max. load 8 kg STANDARD PROGRAMME for the Energy Label consumption values. White and fast coloured cotton. This programme can be selected for slightly or normally soiled cotton items. The temperature will decrease and the washing time will be extended. This allows to obtain a good washing efficiency so saving energy.
Helpful hints and tips 21 Treat curtains with special care. Remove hooks or tie them up in a bag or net. Maximum loads Recommended loads are indicated in the washing programme charts. General rules: • Cotton, linen: drum full but not too tightly packed; • Synthetics: drum no more than half full; • Delicate fabrics and woollens: drum no more than one third full. Washing a maximum load makes the most efficient use of water and energy. For heavily soiled laundry, reduce the load size.
Care and cleaning Ink: depending on the type of ink, moisten the fabric first with acetone1), then with acetic acid; treat any residual marks on white fabrics with bleach and then rinse thoroughly. Tar stains: first treat with stain remover, methylated spirits or benzine, then rub with detergent paste. Detergents and additives Good washing results also depend on the choice of detergent and use of the correct quantities to avoid waste and protect the environment.
Care and cleaning 23 Descaling The water we use normally contains lime. It is a good idea to periodically use a water softening powder in the machine. Do this separately from any laundry washing, and according to the softening powder manufacturer's instructions. This will help to prevent the formation of lime deposits. After each wash Leave the door open for a while. This helps to prevent mould and stagnant smells forming inside the appliance.
Care and cleaning 5. 6. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. Insert the detergent dispenser drawer in the guide rails and push it in. Washing drum Rust deposits in the drum may occur due to rusting foreign bodies in the washing or tap water containing iron. Do not clean the drum with acidic descaling agents, scouring agents containing chlorine or iron or steel wool. 1. 2.
Care and cleaning 2. 3. 4. 5. If necessary wait until the water has cooled down. Open the pump door. Pull flap forward to remove. Place a container close to the pump to collect any spillage. 6. Pull out the emergency emptying hose, place it in the container and remove its cap. 7. When no more water comes out, unscrew the pump cover by turning it anti-clockwise and remove the filter. Use pliers, if necessary. Always keep a rag nearby to dry up any water spillages when removing the cover.
Care and cleaning 11. Replace the filter into the pump by inserting it correctly into the special guides. Screw the pump cover firmly by turning it clockwise. 12. Refit the flap and close the pump door. WARNING! When the appliance is in use and depending on the programme selected there can be hot water in the pump. Never remove the pump cover during a wash cycle, always wait until the appliance has finished the cycle, and is empty.
Care and cleaning 7. 8. 27 Screw the hose back to the machine and make sure the connection is tight. Turn on the water tap. Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, proceed as follows: 1. close the water tap and unscrew the water inlet hose from the tap; 2. place the end of the emergency emptying hose and that of the inlet hose in a bowl placed on the floor and let water drain out; 3.
What to do if… WHAT TO DO IF… Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below.
What to do if… Problem 29 Possible cause/Solution The machine fills then empties immediately: The end of the drain hose is too low. • Refer to relevant paragraph in «Water drainage» section. The machine does not empty and/or does not spin: The drain hose is squashed or kinked. • Check the drain hose connection. The drain filter is clogged. • Clean the drain filter. An option or a programme that ends with the water still in the tub or a that eliminates all the spinning phases has been selected.
What to do if… Problem Possible cause/Solution The door will not open: The programme is still running. • Wait the end of washing cycle. The door lock has not been released. • Wait until the symbol 9.5 has gone off. There is water in the drum. • Select drain or spin programme to empty out the water. The machine vibrates or is noisy: The transit bolts and packing have not been removed. • Check the correct installation of the appliance.
Technical data 31 If you are unable to identify or solve the problem, contact our service centre. Before telephoning, make a note of the model, serial number and purchase date of your machine: the Service Centre will require this information. TECHNICAL DATA Dimensions Width Height Depth Depth (Overall dimensions) 60 cm 85 cm 60 cm 63 cm Electrical connection Voltage - Overall power - Fuse Information on the electrical connection is given on the rating plate, on the inner edge of the appliance door.
Installation they are the most efficient programmes in terms of combined energy and water consumption for washing that type of cotton laundry. They agree with EN60456. The actual water temperature may differ from the declared cycle temperature. INSTALLATION Unpacking All transit bolts and packing must be removed before using the appliance. You are advised to keep all transit devices so that they can be refitted if the machine ever has to be transported again. 1.
Installation 3. Unscrew the three bolts using the key supplied with the machine. 4. Slide out the relevant plastic spacers. 5. Open the porthole, take out the inlet hose from the drum and remove the polystyrene block fitted on the door seal.
Installation 6. 7. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Connect the water inlet hose as described under the paragraph «Water inlet». Positioning and levelling Install the machine on a flat hard floor. Make sure that air circulation around the machine is not impeded by carpets, rugs etc. Before placing it on small tiles, apply a rubber coating.
Installation 1. 2. Open the porthole and extract the inlet hose. Connect the hose with the angled connection to the machine. Do not place the inlet hose downwards. Angle the hose to the left or right depending on the position of your water tap. 3. Set the hose correctly by loosening the ring nut. After positioning the inlet hose, be sure to tighten the ring nut again to prevent leaks. 4. Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance.
Installation Water-stop device The inlet hose is provided with a water stop device, which protects against damage caused by water leaks in the hose which could develop due to natural ageing of the hose. This fault is shown by a red sector in the window «A». Should this occur, turn the water tap off and refer to your Service Centre to replace the hose. A Water drainage The end of the drain hose can be positioned in three ways: 1.
Electrical connection 37 The drain hose may be extended to a maximum of 4 metres. An additional drain hose and joining piece is available from your local Service Centre. ELECTRICAL CONNECTION Information on the electrical connection is given on the rating plate on the inner edge of the appliance door. Check that your domestic electrical installation can take the maximum load required, also taking into account any other appliances in use. WARNING! Connect the machine to an earthed socket.
Packaging materials The materials marked with the symbol are recyclable. >PE<=polyethylene >PS<=polystyrene >PP<=polypropylene This means that they can be recycled by disposing of them properly in appropriate collection containers. Ecological hints To save water, energy and to help protect the environment, we recommend that you follow these tips: • Normally soiled laundry may be washed without prewashing in order to save detergent, water and time (the environment is protected too!).
www.aeg.
