L 75270 FL L 75470 FL CS Návod k použití
www.aeg.com OBSAH 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. BEZPEČNOSTNÍ INFORMACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BEZPEČNOSTNÍ POKYNY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICKÉ INFORMACE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 POPIS SPOTŘEBIČE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ČESKY 3 1. BEZPEČNOSTNÍ INFORMACE Tento návod si pečlivě přečtěte ještě před instalací spotřebiče a jeho prvním použitím. Výrobce nezodpoví‐ dá za škody a zranění způsobená nesprávnou instalací či chybným používáním. Návod k použití vždy uchová‐ vejte spolu se spotřebičem pro jeho budoucí použití. 1.1 Bezpečnost dětí a postižených osob UPOZORNĚNÍ Hrozí nebezpečí udušení, úrazu nebo jiných trva‐ lých následků.
www.aeg.com • Jestliže je poškozený přívodní kabel, smí ho vyměnit pouze výrobce, servisní technik nebo osoba s podob‐ nou příslušnou kvalifikací, jinak by mohlo dojít k úra‐ zu. • Hodnota provozního tlaku vody (minimální a maximál‐ ní) musí být mezi 0,5 bar (0,05 MPa) a 8 bar (0,8 MPa) • Větrací otvory umístěné vespod spotřebiče (jsou-li součástí spotřebiče) nesmí být ničím zakryté (např. kobercem). • Spotřebič musí být připojen k vodovodnímu potrubí pomocí nové dodané soupravy hadic.
ČESKY • Nedotýkejte se napájecího kabelu či síťové zástrčky mokrýma rukama. • Tento spotřebič je v souladu s směrni‐ cemi EEC. Vodovodní přípojka • Dbejte na to, abyste hadice nepoško‐ dili. • Spotřebič musí být připojen k vodo‐ vodnímu potrubí pomocí nové dodané soupravy hadic. Neinstalujte již jednou použitou soupravu hadic znovu. • Před připojením spotřebiče k novým hadicím nebo k hadicím, které nebyly dlouho používané, nechte vodu na ně‐ kolik minut odtéct, dokud nebude či‐ stá.
www.aeg.com Úroveň ochrany proti průniku pevných částic a vlhkosti, kterou zajišťuje ochranný kryt s výjimkou míst, kde není nízkonapěťové vybavení chráněno proti vlhkosti Tlak přívodu vody IPX4 Minimální 0,5 barů (0,05 MPa) Maximální 8 barů (0,8 MPa) Studená voda Přívod vody 1) Maximální množství prá‐ Bavlna dla Rychlost odstřeďování 7 kg Maximální 1200 ot/min (L 75270 FL) 1400 ot/min (L 75470 FL) 1) Přívodní hadici připojte ke kohoutku se závitem 3/4". 4.
ČESKY 4.2 Příslušenství 1 1 Klíč 2 K odstranění přepravních šroubů. 2 Plastové krytky 4 K uzavření otvorů na zadní straně skříně po odstranění přepravních šroubů. 3 Napouštěcí hadice se systémem proti vyplavení K ochraně před možnými úniky vody 4 Plastové koleno K zavěšení vypouštěcí hadice na okraj umyvadla. 3 5. OVLÁDACÍ PANEL 1 2 3 ECO SUPER ECO 20 Min.
www.aeg.com 5 Tlačítko Odložený start 6 Tlačítko Úspora času 7 Tlačítko Extra máchání 8 Tlačítko Skvrny 9 Tlačítko pro snížení rychlosti odstřeďování Tlačítko teploty 10 5.1 Tlačítko Zap/Vyp 1 Stisknutím tohoto tlačítka zapnete nebo vypnete spotřebič. Když zapnete spotřebič, zazní zvukový signál. Funkce AUTO Stand-by spotřebič auto‐ maticky vypne za účelem snížení spotřeby energie, když: • Spotřebič nepoužíváte po dobu pěti minut před tím, než stisknete tlačítko 4 .
ČESKY 9 Dětská pojistka Když se zobrazí tento symbol, nelze dvířka spotřebiče otevřít. Dvířka můžete otevřít až poté, co symbol zmizí. Pokud byl program dokončen, ale symbol se nadále zobra‐ zuje: • V bubnu je voda. • Je zapnutá funkce „Zastavení máchání“. Odložený start D • Délka programu Když se program spustí, začne se odečítat čas v krocích po jedné mi‐ nutě. • Odložený start Když stisknete tlačítko odloženého startu, na displeji se zobrazí čas do odloženého startu.
www.aeg.com Tuto funkci použijte u prádla s odolnými skvrnami. Při nastavení této funkce vložte odstra‐ . ňovač skvrn do komory Tato funkce prodlouží délku pro‐ gramu. Tato funkce není k dispozici u programů s teplotou nižší než 40° C. 5.9 Tlačítko Odstředění 9 Toto tlačítko použijte ke: • Snížení maximální rychlosti odstřeďo‐ vací fáze při nastavování programu. Na displeji se zobrazí pouze ry‐ chlosti odstřeďování dostupné se zvoleným programem. • Vypněte odstřeďovací fázi.
ČESKY 11 6. PROGRAMY Program Teplota Druh náplně max. hmotnost ná‐ plně Cyklus popis Funkce Normálně znečištěná bílá a barevná bavl‐ na. max. 7 kg Praní Máchání Dlouhé odstředění SNÍŽENÍ RY‐ CHLOSTI ODSTŘEĎOVÁNÍ ZASTAVENÍ MÁ‐ CHÁNÍ SKVRNY EXTRA MÁCHÁNÍ ÚSPORA ČASU1) Silně zašpiněná bílá a barevná bavlna. max. 7 kg Předpírka Praní Máchání Dlouhé odstředění SNÍŽENÍ RY‐ CHLOSTI ODSTŘEĎOVÁNÍ ZASTAVENÍ MÁ‐ CHÁNÍ SKVRNY EXTRA MÁCHÁNÍ ÚSPORA ČASU1) Normálně znečištěná bílá a barevná bavl‐ na. max.
www.aeg.com Program Teplota Cyklus popis Funkce Normálně znečištěné prádlo z jemných tka‐ Jemné nin jako akryl, viskó‐ 40 °C – studená za či polyester. max. 3 kg Praní Máchání Krátké odstředě‐ ní SNÍŽENÍ RY‐ CHLOSTI ODSTŘEĎOVÁNÍ ZASTAVENÍ MÁ‐ CHÁNÍ SKVRNY EXTRA MÁCHÁNÍ ÚSPORA ČASU1) Vlna vhodná ke praní v pračce. Vlna urče‐ ná k ručnímu praní a jemné tkaniny s označením „ruční praní“ na etiketě. max.
ČESKY Program Teplota 13 Druh náplně max. hmotnost ná‐ plně Cyklus popis Funkce Rychlý prací pro‐ gram, používá se pro lehce znečištěnou bí‐ lou nebo stálobarev‐ nou bavlnu a směso‐ vé tkaniny. max. 5 kg Praní Máchání Dlouhé odstředění SNÍŽENÍ RY‐ CHLOSTI ODSTŘEĎOVÁNÍ ZASTAVENÍ MÁ‐ CHÁNÍ EXTRA MÁCHÁNÍ 20 Min. - 3 kg 30° Lehce znečištěné bavlněné a syntetic‐ ké prádlo, které bylo nošeno pouze jed‐ nou.
www.aeg.com 7. ÚDAJE O SPOTŘEBĚ Na začátku programu se na displeji zobrazí délka programu pro maximální náplň. Během fáze praní se délka programu vypočítává automaticky a lze ji výra‐ zně zkrátit, je-li množství prádla nižší než je maximální náplň (např. při pro‐ gramu Bavlna 60 °C a maximální náplni 7 kg délka programu přesahuje 2 hodiny; při reálné náplni 1 kg délka programu nedosáhne 1 hodiny). Když spotřebič vypočítává reálnou délku programu, na displeji bliká tečka.
ČESKY 15 8. PŘED PRVNÍM POUŽITÍM 1. 2. Aktivujte vypouštěcí systém přidá‐ ním dvou litrů vody do komory pro hlavní praní dávkovače pracího prostředku. Dejte malé množství pracího prostředku do komory pro hlavní praní dávkovače pracího prostředku. Nastavte a spusťte program pro bavlnu na nejvyšší teplotu bez prá‐ dla. Tímto postupem odstraníte vše‐ chny možné nečistoty z bubnu a va‐ ny spotřebiče. 9. POUŽITÍ SPOTŘEBIČE 1. 2. 3. 4. 5. 6. Otevřete vodovodní kohoutek. Zástrčku zasuňte opět do zásuvky.
www.aeg.com Komora pracího prostředku pro fázi předpírky a program namá‐ čení. Prací prostředek pro předpírku a namáčení přidejte před spuště‐ ním programu. Komora pracího prostředku pro fázi praní. Pokud používáte tekutý prací prostředek, odměřte jej okamžitě před spuštěním programu. Komora pro přísady (aviváž, škrob). Produkt vložte do komory před spuštěním programu. Toto je značka maximálního množství pro tekuté přísady. Komora pro prostředek na odstraňování skvrn.
ČESKY 4. 17 Pří použití tekutého pracího prostředku otočte klapku dolů. S klapkou DOLE: – Nepoužívejte gelové nebo hu‐ sté tekuté prací prostředky. – Nepoužívejte více tekutého pracího prostředku, než je uve‐ deno na klapce. – Nenastavujte fázi předpírky. – Nepoužívejte funkci odložené‐ ho startu. 5. 6. Odměřte prací prostředek a aviváž. Opatrně zavřete dávkovač pracího prostředku. Ujistěte se, že klapka při zasunutí zásuvky nepřekáží. 9.3 Nastavení a spuštění programu 1. 2. 3. 4. 5.
www.aeg.com 9.8 Zrušení odloženého startu 1. Stiskněte tlačítko 4 . Příslušná kontrolka začne blikat. 2. Opakovaně stiskněte 5 , dokud se na displeji neobjeví 0’. 3. Stiskněte tlačítko 4 . Program se spustí. 9.9 Otevřete dvířka Zatímco probíhá program nebo odpočet odloženého startu, dvířka spotřebiče jsou zablokovaná. Otevření dvířek spotřebiče: 1. 2. 3. Stiskněte tlačítko 4 . Symbol zá‐ mku dvířek se na displeji přestane zobrazovat. Otevřete dvířka spotřebiče.
ČESKY • Zapněte knoflíky polštářů, zatáhněte zipy, zapněte háčky a patenty. Svažte pásky. • Vyprázdněte kapsy a jednotlivé kusy prádla rozložte. • Vícevrstvé tkaniny, vlněné prádlo a prádlo s potiskem či obrázky obraťte naruby. • Odstraňte odolné skvrny. • Silně zašpiněné skvrny vyperte pomo‐ cí speciálního pracího prostředku. • Při praní záclon buďte opatrní. Od‐ straňte háčky nebo záclony vložte do pracího pytle nebo povlečení na po‐ lštář.
www.aeg.com Tvrdost vody Úroveň Typ °dH °T.H. mmol/l Clarkovy stupně 4 velmi tvrdá > 21 > 37 >3,7 >25 11. ČIŠTĚNÍ A ÚDRŽBA UPOZORNĚNÍ Před čištěním spotřebiče jej odpojte z elektrické sítě. 11.1 Odstraňování vodního kamene Voda, která se při praní používá, obsa‐ huje vodní kámen. V případě potřeby použijte pro odstranění vodního kamene změkčovač vody. Použijte výrobek speciálně určený pro pračky. Dodržujte pokyny výrobce uve‐ dené na balení těchto výrobků.
ČESKY 21 11.6 Dávkovač pracího prostředku Čištění dávkovače pracího prostředku: 1 1. 2. Stiskněte páčku. Vytáhněte dávkovač ven. 3. Odstraňte horní část komory na přísady. Všechny části omyjte vodou. 2 4. 5. 6. 11.7 Vypouštěcí čerpadlo Vypouštěcí čerpadlo pravidelně kontrolujte a čistěte. Čerpadlo vyčistěte, když: • Spotřebič nevypouští vodu. • Buben se nemůže otáčet. • Spotřebič vydává nezvyklý hluk z dů‐ vodu ucpaného vypouštěcího čerpa‐ dla.
www.aeg.com Čištění vypouštěcího čerpadla: 1. Otevřete dvířka vypouštěcího čerpa‐ dla. 2. Klapku odstraňte jejím vytažením. 3. Pod výklenek vypouštěcího čerpa‐ dla položte nádobu, do které zachy‐ títe vytékající vodu. Stiskněte dvě páčky a vytáhněte vy‐ pouštěcí hadici ven, aby mohla voda vytéct. 4. 1 5. 6. Když je nádoba plná vody, zasuňte vypouštěcí hadici zpět a nádobu vy‐ prázdněte. Kroky 4 a 5 opakujte, do‐ kud z vypouštěcího čerpadla nevy‐ téká žádná voda.
ČESKY 23 Vyčistěte filtr pod vodovodním ko‐ houtkem a vložte jej zpět do čerpa‐ dla do speciálních drážek. 10. Ujistěte se, že jste filtr správně utá‐ hli, abyste zabránili úniku vody. 11. Nasaďte zpět klapku a zavřete dvířka vypouštěcího čerpadla. 9. 2 1 11.8 Filtr v přívodní hadici a filtr přívodního ventilu Tyto filtry může být nutné vyčistit, když: • Spotřebič se neplní vodou. • Spotřebič se plní vodou příliš dlouho. • Kontrolka tlačítka 4 bliká a na disple‐ ji se zobrazí příslušný výstražný kód.
www.aeg.com Když vypustíte vodu pomocí nouzového vypouštění, je nutné vypouštěcí systém opět aktivovat: 1. Do komory pro hlavní praní dávko‐ vače pracího prostředku nalijte dva litry vody. 2. Spusťte program na vypouštění vo‐ dy. 2. 3. 4. 5. 6. 11.10 Opatření proti vlivu mrazu Zavřete vodovodní kohoutek. Odšroubujte přívodní hadici. Oba konce přívodní hadice vložte do nádoby a nechte z hadice vytéct vo‐ du. Vyprázdněte vypouštěcí čerpadlo.
ČESKY Problém 25 Možná příčina Možné řešení Filtr vypouštěcího čer‐ padla je zanesený. Vyčistěte filtr vypouštěcího čer‐ padla. Řiďte se částí „Čištění a údržba“. Vypouštěcí hadice je nesprávně připojena. Zkontrolujte, zda je připojení správné. Byl nastavený prací pro‐ Nastavte vypouštěcí program. gram bez vypouštěcí fá‐ ze. Je zapnutá funkce „Za‐ stavení máchání“. Nastavte vypouštěcí program. Dvířka spotřebiče jsou otevřená ne‐ bo nejsou správně zavřená. Zavřete správně dvířka.
www.aeg.com Problém Možná příčina Možné řešení Nelze otevřít dvířka spotřebiče. Probíhá prací program. Nechte prací program dokončit. V bubnu je voda. Zvolte program vypouštění nebo odstřeďování. Nesprávné vyrovnání spotřebiče. Spotřebič vyrovnejte. Řiďte se pokyny v části „Instalace“. Neodstranili jste obaly nebo přepravní šrouby. Obaly nebo přepravní šrouby odstraňte. Řiďte se pokyny v části „Instalace“. Velmi malá náplň prá‐ dla. Do bubnu přidejte více prádla.
ČESKY 27 13.2 Vybalení 1. Používejte rukavice. Odstraňte vněj‐ ší fólii. V případě potřeby použijte řezák. 2. 3. Odstraňte kartónový vršek. Odstraňte polystyrénový obalový materiál. 4. Odstraňte vnitřní fólii. 5. Otevřete dvířka spotřebiče. Odstraň‐ te polystyrénový díl z těsnění dvířek a všechny předměty z bubnu.
www.aeg.com 6. Na podlahu za spotřebič položte je‐ den kus polystyrénového obalového prvku. Opatrně na něj položte spotřebič jeho zadní stranou. Nepo‐ škoďte hadice. 7. Odstraňte polystyrénovou ochranu ze spodní části spotřebiče. Postavte spotřebič do svislé polohy. 8. 1 2 9. Vyndejte napájecí kabel a vypouště‐ cí hadici z držáků. 10. Vyšroubujte tři šrouby. Použijte klíč dodaný spolu se spotřebičem. 11. Vytáhněte plastové distanční kolíky.
ČESKY 29 12. Plastové krytky zasuňte do otvorů. Tyto krytky naleznete v sáčku s ná‐ vodem k použití. UPOZORNĚNÍ Před instalací spotřebiče od‐ straňte všechny přepravní šrouby a obaly. Obaly a přepravní šrouby dopo‐ ručujeme uschovat pro případné další stěhování spotřebiče. 13.3 Umístění a vyrovnání • Instalujte spotřebič na tvrdé rovné podlaze. • Ujistěte se, koberec nebrání proudění vzduchu pod spotřebičem. • Zkontrolujte, zda se spotřebič nedotý‐ ká zdi ani jiných zařízení či kusů ná‐ bytku.
www.aeg.com 13.4 Přívodní hadice • Připojte hadici ke spotřebiči. Přívodní hadicí otáčejte pouze doleva či dopra‐ va. Povolte kruhovou matici a nastavte ji do správné polohy. 20 O 45 O • Přívodní hadici připojte ke kohoutku se studenou vodou a závitem 3/4". POZOR Ujistěte se, že na jejích spojích nedochází k úniku vody. Pokud je přívodní hadice příliš krátká, nenastavujte ji ani nepou‐ žívejte prodlužovací hadice. Kon‐ taktujte servisní středisko ohled‐ ně výměny přívodní hadice.
ČESKY 31 Pomocí plastového kolena. • Na kraji umyvadla. • Ujistěte se, že se plastové koleno ne‐ může během vypouštění spotřebiče pohybovat. Přivažte koleno k vodovod‐ nímu kohoutku nebo zdi. • Ke stoupacímu potrubí s průduchem. Řiďte se obrázkem. Přímo do odpadní trubky ve výšce minimálně 60 cm a maximálně 100 cm. Konec vypouštěcí hadice musí být odvětrán tj. vnitřní průměr odpadní trubky musí být větší než vnější průměr vypouštěcí hadice. Bez plastového kolena. • K přípojce sifonu. Řiďte se obrázkem.
www.aeg.com Hadici lze prodloužit o maximál‐ ně 400 cm. V případě prodlouže‐ ní hadice nebo ostatních hadic kontaktujte servisní středisko. 14. POZNÁMKY K OCHRANĚ ŽIVOTNÍHO PROSTŘEDÍ Recyklujte materiály označené symbolem . Obaly vyhoďte do příslušných odpadních kontejnerů k recyklaci. Pomáhejte chránit životní prostředí a lidské zdraví a recyklovat elektrické a elektronické spotřebiče určené k likvidaci. Spotřebiče označené příslušným symbolem nelikvidujte spolu s domovním odpadem.
ČESKY 33
www.aeg.
ČESKY 35
132938573-A-222013 www.aeg.