L 75480 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com • If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard. • The operating water pressure (minimum and maximum) must be between 0,5 bar (0,05 MPa) and 8 bar (0,8 MPa) • The ventilation openings in the base (if applicable) must not be obstructed by a carpet. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. 2.
ENGLISH Water connection • Make sure not to cause damage to the water hoses. • The appliance is to be connected to the water mains using the new supplied hose-sets. Old hose sets must not be reused. • Before you connect the appliance to new pipes or pipes not used for a long time, let the water flow until it is clean. • The first time you use the appliance, make sure that there is no leakage. 2.2 Use WARNING! Risk of injury, electrical shock, fire, burns or damage to the appliance.
www.aeg.com Water supply pressure Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Water supply 1) Cold water Maximum load Cotton 8 kg Spin speed Maximum 1400 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 4.
ENGLISH 4.1 Accessories 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 3 4.2 Child safety device • When you activate this device, you cannot close the door. This prevents children or pets to be closed in the drum.
www.aeg.com 4 Start Pause button 5 Delay start button 6 Time save button 7 Extra rinse button 8 Stain button 9 Spin reduction button 10 Temperature button 5.1 On Off button 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated. The AUTO Stand-by function automatically deactivates the appliance to decrease the energy consumption when: • You do not use the appliance for 5 minutes before you press button 4 . – All settings are cancelled.
ENGLISH 9 Child lock You cannot open the appliance door when the symbol is on. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum. • The 'Rinse Hold' function is on. Delay start D • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time.
www.aeg.com This function increases the programme duration. This function is not available with a temperature lower than 40° C. 5.9 Spin button 9 Press this button to: • Decrease the maximum speed of the spin phase when you set a programme. The display shows only the spin speeds available with the set programme. • Deactivate the spin phase. • Activate the 'Rinse Hold' function. Set this function to prevent fabric creases. The appliance does not drain the water when the programme is completed.
ENGLISH Programme Temperature 11 Type of load Cycle max. weight of load description Functions White and coloured cotton with heavy soil. max. 8 kg Prewash Wash Rinses Long spin SPIN REDUCTION RINSE HOLD STAIN EXTRA RINSE TIME SAVE1) Extra Silent 95° - Cold White and coloured cotton with normal soil. max. 8 kg Wash Rinses Stop with water in the drum STAIN EXTRA RINSE TIME SAVE1) Synthetics 60° - Cold Synthetic or mixed Wash fabric items with nor- Rinses mal level of soil. Short spin max.
www.aeg.com Programme Temperature Type of load Cycle max. weight of load description Functions Jeans 60° - Cold All items in jeans. Jersey made items with hi-tech materials. max. 8 kg Wash Rinses Short spin SPIN REDUCTION RINSE HOLD EXTRA RINSE TIME SAVE1) 20 Min. - 3 kg 30° Cotton and synthetic items with light soil or worn only one time. Wash Rinses Short spin SPIN REDUCTION SUPER ECO5) Cold Mixed fabrics (cotton Wash and synthetic items). Rinses max.
ENGLISH Programme1) Type of load Max. load Cotton and synthetic items. up to 1.5 Kg 13 Steam Anticrease This programme helps to dewrinkle the laundry. Steam can be used for dried, washed or worn once laundry. These programmes can reduce creases and odours and make your laundry more smooth. Do not use any detergent. If necessary, remove stains by washing or using localized stain removal. Steam programmes do not perform any hygienic cycle.
www.aeg.com Programmes Wool/Hand wash 30 °C Load (Kg) Energy consumption (kWh) Water consumption (litre) Approximate programme duration (minutes) Remaining moisture (%)1) 2 0.35 57 58 30 Standard cotton programmes Standard 60 °C cotton 8 0.97 46 225 52 Standard 60 °C cotton 4 0.77 45 170 52 Standard 40 °C cotton 4 0.53 44 165 52 1) At the end of spin phase. Off Mode (W) Left On Mode (W) 0.48 0.
ENGLISH 15 Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the laundry. 9.2 Filling the detergent and additives The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch).
www.aeg.com Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 5. When the countdown is completed, the programme starts automatically. Press button 4 to start the programme. The indicator of button 4 is on. Before you press button 4 to start the appliance, you can cancel or change the set of the delay start. You cannot set the delay start with the Steam programme. The drain pump can operate for a short time when the appliance fills water.
www.aeg.com • The door lock symbol goes off. • Press button 1 to deactivate the appliance. After five minutes from the end of the programme, the energy saving function automatically deactivates the appliance. – The door stays locked. – You must drain the water to open the door. When you activate the appliance again, the display show the end of the last set programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty.
ENGLISH • Do not mix different types of detergents. • To help the environment, do not use more than the correct quantity of detergent. • Obey the instructions that you find on the on packaging of these products. • Use the correct products for the type and colour of the fabric, the programme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase. • If your appliance has not the detergent dispenser with the flap device, add the liquid detergents with a dosing ball.
www.aeg.com • Set the hottest cotton wash programme • Use a correct quantity of powder detergent with biological properties. After each wash, keep the door open for a while to prevent mould and to let unpleasant smells go out. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 11.
ENGLISH 5. 6. 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 21 Clean the dispenser recess with a brush. Put back the dispenser in the recess. • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump.
www.aeg.com 5. 1 6. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump. Pull back the drainage duct and turn the filter to remove it. 2 2 1 11.8 The inlet hose filter and the valve filter It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. 7.
ENGLISH 23 To clean the water inlet filters: Close the water tap. Remove the water inlet hose from the water tap. 3. Clean the filter in the inlet hose with a stiff brush. 1. 2. 4. 5. 6. 7. 20° Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 11.9 Emergency drain Because of a malfunction, the appliance cannot drain the water.
www.aeg.com 12. TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • - The anti-flood device is on.
ENGLISH Problem Possible cause The anti-flood device is on. The spin phase does not operate. The programme does not start. There is water on the floor. 25 Possible solution • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load.
www.aeg.com Problem Possible cause Possible solution The appliance fills The end of the drain with water and hose is too low. drain immediately. The washing results are not satisfactory. Make sure that the drain hose is in the correct position. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains.
ENGLISH 27 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses.
www.aeg.com 7. 8. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag.
ENGLISH WARNING! Remove all the packaging and the transit bolts before you install the appliance. 29 We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
www.aeg.com • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 31 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 33
www.aeg.
ENGLISH 35
132936381-B-072013 www.aeg.