L 75480 HFL WASHING MACHINE USER MANUAL
CONTENTS 4 6 6 7 7 9 12 14 15 15 15 17 18 19 21 26 29 SAFETY INFORMATION ENVIRONMENT CONCERNS TECHNICAL INFORMATION PRODUCT DESCRIPTION ACCESSORIES CONTROL PANEL PROGRAMMES BEFORE FIRST USE USING THE APPLIANCE LOADING THE LAUNDRY FILLING THE DETERGENT AND ADDITIVES SETTING AND STARTING A PROGRAMME AT THE END OF THE PROGRAMME HINTS AND TIPS CARE AND CLEANING TROUBLESHOOTING INSTALLATION SERVICE When contacting Service, ensure that you have the following data available.
ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product. We have created it to give you impeccable performance for many years, with innovative technologies that help make life simpler – features you might not find on ordinary appliances. Please spend a few minutes reading to get the very best from it. ACCESSORIES AND CONSUMABLES In the AEG webshop, you’ll find everything you need to keep all your AEG appliances looking spotless and working perfectly.
SAFETY INFORMATION Before the installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance. Always keep these instructions with the appliance also if you move or give it to a different person. The manufacturer is not responsible if an incorrect installation and use causes damage.
ENGLISH • • • • • • internal components and cause leakages or malfunctions. Do not install and connect a damaged appliance. Make sure to remove all packaging and transport bolts. Make sure that the mains plug is disconnected from the mains socket during installation. Only a qualified person must do the electrical installation, the plumbing and the installation of the appliance. This to prevent the risks of structural damage or injury.
ENVIRONMENT CONCERNS PACKAGING MATERIALS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. ECOLOGICAL HINTS To help the environment, use less water and energy, obey these instructions: • Set a programme without the prewash phase to wash laundry with normal soil. • Always start a washing programme with the maximum load of laundry. • If necessary, use a stain remover when you set a programme with a low temperature.
ENGLISH PRODUCT DESCRIPTION 1 2 3 8 9 10 4 5 11 6 7 12 1 Worktop 2 Detergent dispenser 7 Feet for the appliance level 8 Water drain hose 3 Control panel 4 Door handle 9 Hot and Cold water inlet valves 10 Mains cable 5 Rating plate 6 Drain pump 11 Transit bolts 12 Feet for the appliance level ACCESSORIES 1 2 4 3 1 Spanner To remove the transit bolts. 2 Plastic caps To close the holes on the rear side of the cabinet after the removal of the transit bolts.
1 2 3 10 9 1 On/Off button (Aan/Uit - Marche/ Arrêt) 2 Programme knob 3 Display 4 Start Pause button (Start/Pauze Départ/Pause) 5 Delay start button (Startuitstel - Départ Différé) 6 Time saving button (Tijd Besparen Gain de Temps) 7 Extra rinse button (Extra Spoelen Rinçage+) 8 Hot and Cold water connection button (Hot&Cold) 9 Spin reduction button (T/min.) 10 Temperature button (Temp.
ENGLISH 9 CONTROL PANEL ON OFF BUTTON 1 Press this button to activate or deactivate the appliance. A tune sounds when the appliance is activated. The AUTO Stand-by function automatically deactivates the appliance to decrease the energy consumption when: • You do not use the appliance for 5 minutes before you press button 4 . – All settings are cancelled. – Press button 1 to activate the appliance again. – Set again the washing programme and all possible options.
D • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while it operates.
ENGLISH drain the water when the programme is completed. Spin phase is off. 'Rinse Hold' function is on. TEMPERATURE BUTTON 10 Press button 10 to change the default temperature. -- = cold water ACOUSTIC SIGNALS FUNCTION You can hear the acoustic signals when: • You activate the appliance. • You deactivate the appliance. • You press the buttons. • The programme is completed. • The appliance has a malfunction.
PROGRAMMES Programme Temperature Type of load max. weight of load Cycle description Functions Katoen - Blanc/ Couleurs 95° - Cold White and coloured cotton with normal soil. max. 8 kg Wash Rinses Long spin SPIN REDUCTION RINSE HOLD HOT&COLD1) EXTRA RINSE TIME SAVING2) Katoen + Voorwas - Coton + Prélavage 95° - Cold White and coloured cotton with heavy soil. max.
ENGLISH Programme Temperature Type of load max. weight of load 13 Cycle description Functions Centrifugeren/ All fabrics Pompen - Essor- The maximum load of the laundry is relaage /Vidange4) ted to the type of laundry. Drainage of the water Spin phase at the maximum speed. SPIN REDUCTION NO SPIN Spoelen - Rinçage All fabrics One rinse with additive Long spin SPIN REDUCTION RINSE HOLD EXTRA RINSE5) Gordijnen - Rideaux 40° - Cold Set this programme to wash curtains.
4) The default phase of the spin speed is related to cotton items. Set the spin speed. Make sure that it agrees with the laundry. To select the DRAIN programme only, set the function NO SPIN. 5) Press EXTRA RINSE button to add rinses. With a low spin speed the appliance performs delicate rinses and a short spin. 6) Set this programme to decrease the time and the consumption of energy and water. 7) Set this programme to have a good washing results and decrease the energy consumption.
ENGLISH 2. Put a small quantity of detergent in the main wash compartment of the detergent dispenser. Set and start a programme for cotton at the 15 highest temperature without laundry. This removes all possible dirt from the drum and the tub. USING THE APPLIANCE 1. Open the water tap. 2. Connect the mains plug to the mains socket. 3. Press button 1 to activate the appliance. 4. Put the laundry in the appliance. 5. Use the correct quantity of detergent and additives. 6.
The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme. This is the maximum level for the quantity of liquid additives. The compartment for the stain remover.
ENGLISH 4. 17 To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. SETTING AND STARTING A PROGRAMME 1.
2. Press button 4 , the appliance starts the countdown of the delay start. When the countdown is completed, the programme starts automatically. Before you press button 4 to start the appliance, you can cancel or change the set of the delay start. CANCEL THE DELAY START 1. Press button 4 . The related indicator flashes. 2. Press button 5 again and again until the display shows 0’. 3. Press button 4 . The programme starts. OPEN THE DOOR To open the appliance door: 1. Press button 4 .
ENGLISH 19 HINTS AND TIPS THE LAUNDRY LOAD DETERGENTS AND ADDITIVES • Divide the laundry in: white, coloured, synthetics, delicates and wool. • Obey the washing instructions that are on the laundry care labels. • Do not wash together white and coloured items. • Some coloured items can discolour with the first wash. We recommend that you wash them separately for the first times. • Button up pillowcases, close zippers, hooks and poppers. Tie up belts. • Empty the pockets and unfold the items.
Water hardness table Level Type Water hardness °dH °T.H. mmol/l Clarke 1 soft 0-7 0-15 0-1.5 0-9 2 medium 8-14 16-25 1.6-2.5 10-16 3 hard 15-21 26-37 2.6-3.7 17-25 4 very hard > 21 > 37 >3.
ENGLISH 21 CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. • Use a correct quantity of powder detergent with biological properties. After each wash, keep the door open for a while to prevent mould and to let unpleasant smells go out. DESCALING EXTERNAL CLEANING The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines.
DETERGENT DISPENSER To clean the dispenser: 1 1. Press the lever. 2. Pull the dispenser out. 2 3. 4. 5. 6. DRAIN PUMP Regularly examine the drain pump and make sure that it is clean. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump. • The display shows an alarm code because of the problem with water drain. Remove the top part of the liquid additive compartment.
ENGLISH 23 To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. 4. 1 5. 6. 2 When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 2 1 THE INLET HOSE FILTERS AND THE VALVE FILTERS It could be necessary to clean the filters when: • The appliance does not fill with water. • The appliance fills with the water for a long time. • The indicator of button 4 flashes and the display shows the related alarm.
ENGLISH EMERGENCY DRAIN Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water.
TROUBLESHOOTING The start of the appliance does not occur or it stops during operation. First try to find a solution to the problem (refer to the table). If not, contact the service centre. With some problems, the acoustic signals operate and the display shows an alarm code: • - The appliance does not fill with water. • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. • - The anti-flood device is on.
ENGLISH Problem Possible cause The anti-flood device is on. The spin phase does not operate. The programme does not start. 27 Possible solution • Disconnect the appliance. • Close the water tap. • Contact the service centre. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again.
Problem Possible cause Possible solution The appliance fills with water and drain immediately. The end of the drain hose is too low. Make sure that the drain hose is in the correct position. The washing results are not satisfactory. The detergent you used was not sufficient or correct. Increase the detergent quantity or use a different one. You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set.
ENGLISH 29 INSTALLATION UNPACKING 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
6. Put the front piece on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 8. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers.
ENGLISH 31 12. Replace the plastic spacers with the plastic caps. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. POSITIONING AND LEVELLING x4 • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
THE INLET HOSES • Connect the inlet hoses to the appliance. Turn the inlet hoses only left or right. Loose the ring nut to set it in the correct position. 45 O 35 O CAUTION! Make sure that you connect the cold and hot inlet hoses in the correct position: • (A) Cold water • (B) Hot water. • Connect the water inlet hoses to the cold and hot water taps with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if one of the inlet hoses are too short.
ENGLISH WATER DRAINAGE 33 There are different procedures to connect the drain hose: With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e.
• Directly to a built-in drain pipe in the room wall and tighten it with a clip. You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension.
ENGLISH 35
www.aeg.