LAVAMAT 76819 Waschautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bedienblende . . . . . . . . . . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 25 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 Aufstellung des Gerätes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gerät transportieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Entfernen der Transportsicherung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Aufstellort.
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. • Bei Geräteanlieferung in Wintermonaten mit Minustemperaturen: Waschautomat vor Inbetriebnahme für 24 Stunden bei Raumtemperatur lagern. Bestimmungsgemäße Verwendung • Der Waschautomat ist nur zum Waschen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Waschautomaten sind nicht zulässig.
bei Festanschluss – LS-Schalter im Sicherungskasten ausschalten bzw. Schraubsicherung ganz herausdrehen. • Bei Betriebspausen das Gerät vom Stromnetz trennen und Wasserhahn schließen. • Netzstecker nie am Kabel aus der Steckdose ziehen, sondern am Stecker. • Vielfachstecker, Kupplungen und Verlängerungskabel dürfen nicht verwendet werden. Brandgefahr durch Überhitzung! • Den Waschautomaten nicht mit einem Wasserstrahl abspritzen.
Gerätebeschreibung Bedienblende Waschmittelschublade Typschild (hinter Einfülltür) Sockelklappe/ Laugenpumpe Schraubfüße (höhenverstellbar) Bedienblende Taste Schleudern/SPÜLSTOPP Multidisplay Taste ZEITVORWAHL Programmzusatz-Tasten Taste START/PAUSE Programmablauf-Anzeige Anzeige TÜR Programmwähler Anzeige ÜBERDOSIERT 7
Programmübersicht • 40-60 MIX 6kg • PFLEGELEICHT 60, 50, 40, 30 3kg • LEICHTBÜGELN 40 1kg FEINWÄSCHE 40, 30 3kg WOLLE/SEIDE H (Handwäsche) 40, 30, KALT FEINSPÜLEN • • • • • • • •4) • • • • • • • • • • • • •4) • • • • • • • • • • • • • • 2kg • • 3kg • • ZEITSPAREN SPÜLSTOPP 6kg Schleudernniedrig KOCHWÄSCHE/BUNTWÄSCHE 95, 60, 40, 30 Schleudernhoch • SENSITIV 6kg FLECKEN EXTRA SPÜLEN ENERGIESPAREN 2) Programm Schleuderdrehzahl VORWÄSCHE max.
Anwendung/Eigenschaften Energiesparprogramm bei 60 °C für leicht bis normal verschmutzte Koch-/Buntwäsche aus Baumwolle/Leinen. Programm für normal bis stark verschmutzte Koch-/Buntwäsche aus Baumwolle/ Leinen. Programm für Koch-/Buntwäsche, welche für unterschiedliche Waschtemperaturen gekennzeichnet ist. Teile, die laut Pflegekennzeichen üblicherweise bei 40 °C oder bei 60 °C getrennt gewaschen werden, können in diesem Programm zusammen gewaschen werden.
Vor dem ersten Waschen 1. Waschmittelschublade öffnen. 2. Etwa 2 Liter Wasser durch die Waschmittelschublade in den Waschautomaten gießen. Beim nächsten Programmstart wird dadurch der Laugenbehälter geschlossen und die ÖKO-Schleuse kann ordnungsgemäß funktionieren. 3. Um eventuelle fertigungsbedingte Rückstände aus Trommel und Laugenbehälter zu entfernen, den ersten Waschgang ohne Wäsche durchführen. Programm: KOCHWÄSCHE/BUNTWÄSCHE 95, Taste ZEITSPAREN drücken, ca. 1/4 Messbecher Waschpulver zugeben.
Waschgang durchführen Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: am Griff der Einfülltür ziehen. Die Anzeigen TÜR und START/PAUSE zeigen bei eingeschaltetem Gerät an, ob die Einfülltür geöffnet werden kann: Anzeige TÜR Anzeige START/PAUSE Tür öffnen möglich? leuchtet grün blinkt rot oder ist aus ja leuchtet grün leuchtet rot ja, nach Drücken der Taste START/PAUSE leuchtet rot oder ist aus blinkt rot oder leuchtet rot nein, zu hoher Wasserstand bzw. zu hohe Temperatur 2.
1. Waschmittelschublade bis zum Anschlag herausziehen 2. Wasch-/Pflegemittel einfüllen. 3. Waschmittelschublade ganz hineinschieben. Waschpulver/Tabs für die Hauptwäsche Weichspüler/ Formspüler/ Stärke Fleckensalz/-tabs Waschpulver/Tabs für die Vorwäsche oder Wasserenthärter Waschpulver/Tabs für die Hauptwäsche Wenn Sie Wasserenthärter benutzen und das rechte Fach für Vorwaschmittel benötigen, den Wasserenthärter auf das Hauptwaschmittel in das linke Fach geben.
Schleuderdrehzahl ändern/Spülstopp wählen 3 Der Waschautomat schlägt die maximal zulässige Drehzahl vor, die für das gewählte Programm geeignet ist. Diese Drehzahl können Sie verringern: Dazu Taste Schleudern/SPÜLSTOPP so oft drücken, bis die gewünschte Anzeige leuchtet. Die Drehzahl für das Endschleudern kann während des Programms noch geändert werden. Dazu: 1. Taste START/PAUSE drücken. 2. Drehzahl ändern. 3. Taste START/PAUSE erneut drücken.
VORWÄSCHE Warmes Vorwaschen vor dem automatisch folgenden Hauptwaschgang; mit Zwischenschleudern bei KOCH-/BUNTWÄSCHE und PFLEGELEICHT, ohne Zwischenschleudern bei FEINWÄSCHE. FLECKEN Für stark verschmutzte oder verfleckte Wäsche. Fleckenmittel wird zeitoptimiert während des Programmablaufs eingespült. Nur für Waschtemperaturen ab 40°C einstellbar, da Fleckenmittel erst bei höheren Temperaturen wirksam werden.
Ablauf des Programms 3 • Die Programmablauf-Anzeige zeigt den Programmschritt an, der gerade ausgeführt wird. • Das Multidisplay zeigt die voraussichtliche Restlaufzeit (in Minuten) bis zum Programmende an. Die Restlaufzeit kann sich während des Waschvorgangs verlängern oder kurz stehen bleiben, da sich das Programm an unterschiedliche Bedingungen beim Waschen anpasst (z. B. Wäscheart und -menge, Unwuchterkennung beim Schleudern, Sonderspülgang etc.).
Wenn SPÜLSTOPP gewählt war: Nach Spülstopp leuchtet ENDE auf der Programmablauf-Anzeige. Zuerst muss das Wasser abgepumpt werden: – Entweder Programmwähler auf AUS, anschließend auf PUMPEN drehen und Taste START/PAUSE drücken (es wird ohne Schleudern abgepumpt), – oder Programmwähler auf AUS und anschließend auf SCHLEUDERN drehen. Gegebenenfalls Drehzahl ändern und Taste START/PAUSE drücken (es wird abgepumpt und geschleudert).
Reinigen und Pflegen Achtung! Keine Möbelpflegemittel oder aggressive Reinigungsmittel zur Reinigung des Gerätes benutzen. Bedienblende und Gehäuse mit einem feuchten Tuch abwischen. Reinigungswaschgang Falls überwiegend mit niedriger Temperatur gewaschen wird, von Zeit zu Zeit ein Kochprogramm durchführen. So werden eventuelle Ablagerungen reduziert und das Gerät wird von innen gereinigt. Waschmittelschublade Die Waschmittelschublade sollte regelmäßig gereinigt werden. 1.
Einfülltür und Gummimanschette Regelmäßig prüfen, ob Ablagerungen oder Fremdkörper in den Falten der Gummimanschette oder innen am Türglas vorhanden sind. Türglas und Gummimanschette regelmäßig reinigen. Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs einer der folgenden Fehlercodes im Multidisplay angezeigt wird: – E10 (Probleme mit Wasserzulauf), – E20 (Probleme mit Wasserablauf), – E40 (Einfülltür offen), sehen Sie bitte in nachfolgender Tabelle nach.
Problem E10 erscheint. Anzeige ENDE blinkt 1x, gleichzeitig ertönt 1x ein Signalton. (Probleme mit Wasserzulauf.) Waschautomat vibriert während des Betriebs oder steht unruhig. Wäsche ist nicht geschleudert. Mögliche Ursache Abhilfe Wasserhahn geschlossen. Wasserhahn öffnen. Sieb in der Verschraubung des Zulaufschlauchs verstopft. Wasserhahn schließen. Schlauch abschrauben, Sieb herausnehmen und reinigen. Wasserhahn verkalkt oder defekt. Wasserhahn prüfen, gegebenenfalls reparieren lassen.
Problem Mögliche Ursache Knick im Ablaufschlauch. Maximale Pumphöhe von 1m überschritten. E20 erscheint. Anzeige ENDE blinkt 2x, gleichzeitig ertönt 2x ein Signalton. Laugenpumpe verstopft. (Probleme mit Wasserablauf.) Weichspüler nicht eingespült, Fach w für Pflegemittel mit Wasser gefüllt. Einfülltür lässt sich bei eingeschaltetem Gerät nicht öffnen. Wäsche stark verknittert. 20 Abhilfe Knick entfernen. Bitte an den Kundendienst wenden. Gerät ausschalten. Netzstecker ziehen. Laugenpumpe reinigen.
Wenn das Waschergebnis nicht befriedigend ist Wäsche ist vergraut und in der Trommel lagert sich Kalk ab • Das Waschmittel wurde zu gering dosiert. • Es wurde nicht das richtige Waschmittel eingesetzt. • Spezielle Verschmutzungen wurden nicht vorbehandelt. • Programm oder Temperatur wurden nicht richtig eingestellt. Auf der Wäsche sind graue Flecken • Mit Salben, Fetten oder Ölen verschmutzte Wäsche wurde mit zu wenig Waschmittel gewaschen. • Es wurde mit zu niedriger Temperatur gewaschen.
Notentleerung durchführen 1 Warnung! Waschautomat vor Notentleerung ausschalten und den Netzstecker aus der Steckdose ziehen! Warnung! Die Waschlauge, die aus dem Notentleerungsschlauch ausläuft, kann heiß sein. Verbrühungsgefahr! Vor einer Notentleerung Waschlauge abkühlen lassen! 1. Sockelklappe aufklappen und abziehen. 2. Notentleerungsschlauch herausnehmen. 3. Flaches Auffanggefäß unterstellen. Anschließend Verschlussstopfen durch Drehen gegen den Uhrzeigersinn lösen und herausziehen. 4.
Laugenpumpe 1 Die Laugenpumpe ist wartungsfrei. Das Öffnen des Pumpendeckels ist nur im Störungsfall erforderlich, wenn kein Wasser mehr abgepumpt wird, z. B. bei blockiertem Pumpenrad. Bitte vor dem Einfüllen der Wäsche immer sicherstellen, dass sich keine Fremdkörper in den Taschen oder zwischen der Wäsche befinden. Büroklammern, Nägel etc., die eventuell mit der Wäsche in den Waschautomaten gelangt sind, bleiben im Pumpengehäuse (Fremdkörperfalle, die das Pumpenrad schützt) liegen.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 850 x 598 x 603mm Tiefe bei geöffneter Einfülltür 980 mm Höhenverstellbarkeit ca. +10/-5mm Füllmenge (programmabhängig) max.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Dieser Waschautomat ist nicht unterbaufähig. • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann es beim Schleudern zu Schäden am Gerät oder an benachbarten Möbeln kommen.
Aufstellung des Gerätes Gerät transportieren 1 Warnung! Der Waschautomat hat ein hohes Gewicht. Verletzungsgefahr! Vorsicht beim Anheben. • Das Gerät nicht auf die Vorderfront und nicht auf die rechte Seite (von vorne gesehen) legen. Elektrische Bauteile können nass werden. • Gerät niemals ohne Transportsicherung transportieren. Transportsicherung erst am Aufstellort entfernen! Transport ohne Transportsicherung kann zu Schäden am Gerät führen.
2. Entfernen Sie das Stromkabel und den Ablaufschlauch aus den Halterungen der Waschmaschinenrückwand. 3. Schrauben Sie mit einem Schlüssel, der dem Gerät beiliegt, die zentrale Schraube A an der Rückwand des Waschautomatens heraus. Ziehen Sie den Plastikzapfen heraus. 4. Schrauben Sie die zwei großen Schrauben B und die sechs kleineren seitlichen Schrauben C an der Rückwand des Waschautomaten heraus.
5. Ziehen Sie die Stahlschiene D ab. 6. Schrauben Sie die sechs kleineren seitlichen Schrauben C wieder auf. 7. Öffnen Sie die Tür und entnehmen Sie den Zulaufschlauch aus der Trommel. Entfernen Sie den mit dem Klebeband fixierten Polystyrolblock aus der Türdichtung.
8. Verschließen Sie die kleinere obere Öffnung und die zwei größeren seitlichen Öffnungen mit den Kunststoffabdeckungen, die dem Gerät beiliegen. Hinweis: Wir empfehlen, die Transportsicherungsteile aufzubewahren, um sie bei Umzug wieder verwenden zu können. Gerät niemals ohne Transportsicherung transportieren. Vor einem Umzug das Gerät vollständig entleeren, wie im Kapitel „Notentleerung durchführen” beschrieben. Aufstellort Achtung! Das Gerät darf nicht in einem frostgefährdeten Raum betrieben werden.
Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen. Das Typschild ist im Bereich der Einfüllöffnung angebracht. Wasseranschluss Zulässiger Wasserdruck Der Wasserdruck muss mindestens 1bar (=10N/cm2 =0,1MPa) und darf höchstens 10bar (=100N/cm2 =1MPa) betragen. – Bei mehr als 10bar: Druckminderventil vorschalten.
4. Schließen Sie den Schlauch an einen Wasserhahn mit Schlauchverschraubung 3/4" an. Verwenden Sie stets den mit dem Gerät mitgelieferten Schlauch. Aqua-Control Aqua-Control schützt zusätzlich vor Wasserschäden durch Alterungsschäden des Wasserzulaufschlauchs. In diesem Fall blockiert Aqua-Control die Wasserzufuhr zum Gerät. Die Störung wird durch eine rote Markierung im Fensterchen „A” angezeigt. Der Kundendienst muss verständigt und der Zulaufschlauch ersetzt werden.
Wasserablauf Der Höhenunterschied zwischen Standfläche und Wasserabfluss darf höchstens 1 Meter betragen. Zur Verlängerung dürfen nur Originalschläuche verwendet werden. (Max. 3 m auf dem Fußboden verlegt und dann bis 80 cm hoch). Der Kundendienst führt Ablaufschläuche in verschiedenen Längen. Wasserablauf in einen Siphon Die Verbindungsstelle Tülle/Siphon mit einer Schlauchschelle (im Fachhandel erhältlich) sichern. 1 Wasserablauf in ein Waschbecken/Badewanne Achtung! – Kleine Becken sind nicht geeignet.
Garantie/Kundendienst Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Österreich Sehr geehrter Kunde! Wir, die Electrolux Hausgeräte GmbH, beglückwünschen Sie zum Erwerb eines Gerätes aus dem Electrolux Konzern. Für dieses Gerät räumen wir Ihnen, als Verbraucher im Sinne des Konsumentenschutzgesetzes gemäß den nachstehenden Bedingungen, eine besondere Garantie ein, die Ihnen zusätzliche Rechte gewährt. 1. Die Garantie beginnt mit dem Tag an dem das Gerät gekauft wurde und erstreckt sich über einen Zeitraum von 24 Monaten.
Luxembourg 1. Unbeschadet etwaiger Ansprüche gegen Dritte wird dieses Gerät von unserem Kundendienst gemäß den folgenden Garantiebedingungen instandgesetzt, wenn es trotz sachgemäßer Behandlung und Beachtung der gültigen Einbauvorschriften, Betriebsanleitungen und vorschriftsmäßigem Anschluß infolge eines Fertigungs- oder Materialfehlers versagen sollte. 2.
Österreich Unsere Kundendienststellen und Servicepartner Electrolux stellt Ihnen hiermit jene Partner vor, die dafür garantieren, dass wir Ihnen Top-Qualität mit unseren Kundendiensteinrichtungen jetzt und in Zukunft bieten. Unsere Kundendienststellen in den Bundesländern sind spezialisiert auf unsere Marken: AEG, Electrolux, Juno, Zanussi. Zentrale: Kundendienst Wien, Niederösterreich, nördliches Burgenland Electrolux Hausgeräte GmbH 1230 Wien, Herziggasse 9 Tel. Reparaturannahme 01/86640-330 Tel.
Ersatzteile, Zubehör und Pflegemittel Für Oesterreich: Sie können Ersatzteile, Zubehör und Pflegemittel online bestellen bei http://www.aeg-hausgeraete.at Luxembourg AEG ELECTROLUX Service-Center, 7, rue de Bitbourg L-1273 Luxembourg-Hamm Telefon: 4 24 31-433 Telefax: 4 24 31-460 Europäische Garantie Für dieses Gerät besteht in den am Ende dieser Benutzerinformation aufgeführten Ländern eine Garantie von Electrolux für den Zeitraum, der in der Gerätegarantie oder andernfalls gesetzlich festgelegt ist.
p t b España +34 902 11 63 88 Carretera M-300, Km. 29,900 Alcalá de Henares Madrid France www.electrolux.fr Great Britain +44 8705 929 929 Addington Way, Luton, Bedfordshire LU4 9QQ Hellas +30 23 10 56 19 70 4 Limnou Str., 54627 Thessaloniki Hrvatska +385 1 63 23 338 Slavonska avenija 3, 10000 Zagreb Ireland +353 1 40 90 753 Long Mile Road Dublin 12 Italia +39 (0) 434 558500 C.so Lino Zanussi, 26 - 33080 Porcia (PN) Latvija +37 17 84 59 34 Kr.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Ausstattung Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-electrolux.de E-Mail: aeg-hausgeraete.kundenservice@aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
www.electrolux.com www.aeg-electrolux.de www.aeg-electrolux.at www.aeg-electrolux.be www.aeg-electrolux.lu www.aeg.