L 77480 FL EN User manual
www.aeg.com/au CONTENTS 1. 2. 3. 4. 6. 7. 8. 9. 10. 11. 12. 13. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 CONTROL PANEL . . . . . . . . . . . . . . . . . . . . . . . .
ENGLISH 1. 3 SAFETY INSTRUCTIONS 1.3 Child safety device 1.1 Conditions of use This appliance is intended to be used in household and similar applications such as: • Farm houses. • By clients in serviced apartments, holiday apartments and other residential type environments. Before installation and use, read this manual carefully: • For your safety and the safety of your property • To help the environment • For the correct operation of the appliance.
www.aeg.com/au 1.6 Installation • The appliance is heavy, be careful when you move it. • Do not transport your appliance without the transit bolts, you can damage internal components and cause leakages or malfunctions. • Do not install and connect a damaged appliance. • Make sure to remove all packaging and transit bolts before first use. • Make sure that the mains plug is disconnected from the mains socket during installation.
ENGLISH Electrical connection: Voltage Overall power Frequency 230-240 V 2200 W 50 Hz Level of protection against ingress of solid particles and moisture ensured by the protective cover, except where the low voltage equipment has no protection against moisture Water supply pressure 5 IPX4 Minimum 0,5 bar (0,05 MPa) Maximum 8 bar (0,8 MPa) Cold water Water supply 1) Maximum load Cotton Spin speed Maximum 8 kg 1400 rpm 1) Connect the water inlet hose to a water tap with a 3/4'' thread. 3.
www.aeg.com/au 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Anti-flood inlet hose To prevent possible leakage 4 Plastic hose guide To connect the drain hose on the edge of a sink. 3 4. CONTROL PANEL 1 2 Cottons Economy Super Eco 3 Cottons + Prewash 20 Min.
ENGLISH 7 5.3 Display 3 A B C D The display shows: A • The maximum temperature of the programme. B • The default spin speed of the programme. • 'No Spin'1) and 'Rinse Hold' symbols. C • The display symbols.2) Symbols Description Washing phase Rinse phases Spin phase Child lock You cannot open the door when this symbol is on. You can open the door only when the symbol goes off. If the programme is completed but the symbol stays on: • There is water in the drum. • The 'Rinse Hold' function is on.
www.aeg.com/au D • The programme time When the programme starts, the time decreases with steps of 1 minute. • The delay start When you press the delay start button, the display shows the delay start time. • Alarm codes If the appliance has a malfunction, the display shows alarm codes. Refer to 'Troubleshooting' chapter. • Err The display shows this message for some seconds if: – You set a function that is not applicable for the programme. – You change the programme while in operation.
ENGLISH Spin phase is off. 'Rinse Hold' function is on. 5.10 Temperature button 10 Press button 10 to change the default temperature. -- = cold water 9 • To activate the function, press button 10 and button 9 at the same time until the display shows the symbol . • To deactivate the function, press button 10 and button 9 at the same time until the symbol goes off. You can activate the function: • Before you press button 4 : the appliance cannot start.
www.aeg.com/au Programme Type of load TemperaMax. weight of load ture Cycle de- Functions scription Cottons + Prewash 95° - Cold White and coloured cotton with heavy level of soil. max. load 8 kg Wash Spin Reduction Rinses Rinse Hold Long spin Prewash1) Stains2) Extra Rinse Time Save3) Extra Silent 95° - Cold White and coloured cotton. max.
ENGLISH Programme Type of load TemperaMax. weight of load ture Cycle de- Functions scription Spin / Drain All fabrics. 5) The maximum load of the laundry is related to the type of laun0° dry. Drainage Spin Reduction of the wa- No Spin ter Spin phase. Rinse All fabrics. max. load 8 kg One rinse Spin Reduction with addi- Rinse Hold tive Extra Rinse6) Spin phase Curtains 40° - Cold Set this programme to wash curtains. It adds automatically the prewash phase to clean the dust.
www.aeg.com/au 4) The wash and spin phase is delicate to prevent the creases of the laundry. The appliance adds some rinses. 5) The default phase of the spin speed is related to cotton items. Set the spin speed. Make sure that it agrees with the laundry. To select the DRAIN programme only, set the function NO SPIN. 6) Press Extra Rinse button to add rinses. With a low spin speed the appliance performs delicate rinses and a short spin.
ENGLISH 13 Make sure that no laundry stays between the seal and the door. There is a risk of water leakage or damage to the seal or laundry. 8.2 FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it in immediately before you start the programme.
www.aeg.com/au Check the position of the flap 1. Pull out the detergent dispenser until it stops. 2. Press the lever down to remove the dispenser. 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit shown on the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6.
ENGLISH 5. Press button 4 to start the programme. The indicator of button 4 is on. The appliance adjust automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. After approximately 15 minutes from the start of the programme, the display shows the new time value. 8.4 Interrupt a programme 15 Before you press button 4 to start the appliance, you can cancel or change the delay start setting. 8.8 Cancel the delay start 1.
www.aeg.com/au saving function automatically deactivates the appliance. When you activate the appliance again, the display shows the set of the last performed programme. Turn the programme knob to set a new cycle. • Remove the laundry from the appliance. Make sure that the drum is empty. • Keep the door ajar, to prevent mildew and odours. • Close the water tap. The washing programme is complete but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry.
ENGLISH gramme temperature and the level of soil. • If you use liquid detergents, do not set the prewash phase. • If your appliance does not have the detergent dispenser with the flap device, add the liquid detergents with a dosing ball. 9.4 Water hardness If the water hardness in your area is high or moderate, we recommend that you use a water softener for washing machines. In areas where the water hard- 17 ness is soft it is not necessary to use a water softener.
www.aeg.com/au 10.4 Door seal Regularly examine the seal and remove all objects from the inner part. 10.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 10.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever. Pull the dispenser out. 3.
ENGLISH 10.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 19 • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
www.aeg.com/au 2 1 10.8 The inlet hose filter and the valve filter 7. Remove fluff and objects from the pump. 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you correctly tighten the filter to prevent leakages. 11. Put the flap back and close the drain pump door.
ENGLISH 4. 5. 6. 7. 20° 21 Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 10.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
www.aeg.com/au • • - The appliance does not drain the water. • - The appliance door is open or not closed correctly. - The anti-flood device is on. WARNING! Deactivate the appliance before you do the checks. Problem Possible cause Possible solution The appliance does not fill with water. The water tap is closed. Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose are blocked . Clean the filters.
ENGLISH Problem The programme does not start. There is water on the floor. 23 Possible cause Possible solution The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse. You did not press button 4 .
www.aeg.com/au Problem Possible cause Possible solution You did not remove stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. Incorrect temperature was set. Make sure that you set the correct temperature. Excessive laundry load. Decrease the laundry load. After the check, activate the appliance. The programme continues from the point of interruption. If the problem occurs again, contact the service centre.
ENGLISH 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully lay the appliance down with the rear side on the packaging. Make sure you do not damage the hoses. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. Pull up the appliance back into vertical position. 8.
www.aeg.com/au 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Cover the holes with the plastic caps provided in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance.
ENGLISH 27 12.2 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level. The correct adjustment of the appliance levelling feet prevents the vibration, noise and the movement of the appliance when in operation. x4 • The appliance must be level and stable.
www.aeg.com/au • Connect the water inlet hose to the cold water tap with ¾” thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 29 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com/au the same meaning referred to in the ACL; b) ‘ACL’ means Trade Practices Amendment (Australian Consumer Law) Act (No.
ENGLISH – incomplete or improper installation – incorrect, improper or inappropriate operation – insect or vermin infestation – failure to comply with any additional instructions supplied with the Appliance; b) the Appliance is modified without authority from AEG in writing; c) the Appliance’s serial number or warranty seal has been removed or defaced; d) the Appliance was serviced or repaired by anyone other than AEG, an authorised repairer or ASC. 8.
www.aeg.com/au FOR SERVICE or to find the address of your nearest state service centre in Australia PLEASE CALL 1300 363 664 OR EMAIL customercare@aegaustralia.com.au For the cost of a local call (Australia only) FOR SPARE PARTS or to find the address of your nearest state spare parts centre in Australia PLEASE CALL 13 13 50 OR EMAIL customercare@aegaustralia.com.
ENGLISH 33
www.aeg.
ENGLISH 35
132931131-A-402012 www.aeg.
