LAVAMAT 86810 Washing machine User information
Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . What is shown in the display . . . . . . . . . . . . . . . .
If the wash results are not satisfactory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Carrying out an emergency drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 Drain pump. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 Technical data. . . . . . . . . . . . . . . . . . . . . . . . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. • If the appliance is delivered in the winter months when there are minus temperatures: Store the washing machine at room temperature for 24 hours before using for the first time. Correct use • The washing machine is only designed for the washing of normal domestic laundry at home. • Additions or modifications to the washing machine are not permitted.
General safety • Repairs to the washing machine must only be carried out by qualified service engineers. • Never use the washing machine if the mains cable is damaged; or if the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • Switch off the washing machine before cleaning, maintenance and servicing.
Description of the appliance Detergent dispenser drawer Control panel Rating plate (behind door) Plinth flap/ Drain pump Screw feet (height adjustable) Control panel Programme knob and On/Off dial Display Function keys START/PAUSE key What is shown in the display Information field, shows the current settings COTTON Cycle end at Temperature 12.45 Current time 15.
Program overview • 6kg • • • • LINEN/EASY-CARES 60°, 50°, 40°, 30°, Cold cycle 6kg or 3kg • • •4) • 40 - 60 MIX 6kg • • • • DELICATE 40°, 30°, Cold cycle 3kg • •4) • WOOL/ (HANDWASH) 40°, 30°, Cold cycle COTTON SILK/ (HANDWASH) SPIN RINSE RINSE HOLD • • • • • • •3) •3) • • • • • •3) •3) • • • • • • • • • • • • • • 2kg • • • • 1kg • • • • SHORT 0 • 1200/1000/ 800/600/400 NIGHT CYCLE • 1600/1400 STAIN 6kg Spin speed DELAY START SENSI
Care symbols1) Use/Features Energy-saving program at 60 °C for lightly to normally soiled whites/coloureds made of cotton/linen. MO Program at 95 °C for normally to heavily soiled whites/coloureds made of cotton/linen. O General program for whites/coloureds made of cotton/linen as well as for easy-care mixed fibres and synthetics. The program is automatically adjusted to the different fabric types and load sizes. If loading only with easy-care washing, do not load more than 3kg.
Prior to using for the first time Switching on the appliance for the first time - setting the language 3 The display is set to English as standard in the factory. Important: If the display does not show the menu for setting the language when the appliance is switched on, the appliance has been switched on before. If this happens, please see the section “Setup/Language”. To switch on the appliance, turn the program knob to any program, e. g. COTTON.
Setting the time So that the time and the end of the program are correctly displayed, please check the display and set the current time if necessary. To do this, please see the section “Setup/Clock”. Carrying out a wash program prior to first use In order to remove any residues from the drum and water container which may have been left during manufacturing, perform the first wash cycle without any washing in the machine. Program: LINEN/EASYCARES 60 °C, option TIME SAVING: VERY SHORT, use approx.
Running a washing cycle Opening the door/loading washing 1. To open the door: pull the door by the handle. 2. Unfold washing and load it loosely into the machine. Mix large and small items. Important: Do not get any washing caught between the door and the rubber seal. 3. Push the door shut firmly. Door catch must audibly click shut. Adding detergent/additives Important: Use only detergents and additives that are suitable for use in domestic washing machines.
1. Pull the detergent dispenser drawer out as far as the stop. 2. Add the detergent/additives. 3. Push the drawer in fully.
– The lighting for the display switches itself off at the end of the cycle or, if the appliance is not started after the program is set, after 10 minutes. To switch the light on again, press any key or turn the program knob. Changing the temperature Press the TEMPERATURE key repeatedly until the desired temperature is displayed. 12.45 LINEN/EASY CARE Cycle end at 14.
SENSITIVE Enhanced rinse action through an additional rinse cycle together with decreased drum movement (improved fabric care). This is ideal when frequent washes are necessary, for example, in cases of highly sensitive skin. An additional rinse cycle can also be permanently set (see section “Setup”). STAIN For heavily soiled and stained washing. In-wash stain treatment products are washed in at the optimum time as the program progresses. NIGHT CYCLE The washing is left to soak in the final rinse water.
3 repeatedly until the symbol for the option flashes and then press the OK key. The black bar under the symbol disappears. If other options are to be selected: Press the OPTION key repeatedly until the desired symbol flashes and confirm each one with the OK key. 3. Press the OPTION key 12.45 LINEN/EASY CARE repeatedly, until your pro14.56 Cycle end at gram set appears again. The display shows the symbol for 50C 800 aýýýýýVýaýaýaýaýaýaýaýa the selected option.
3 4. To change from SHORT to VERY SHORT, press the TIME key again. 12.45 14.12 Time saving VERY SHORT aýýýýýaýaýaýaýaýaýaýK_ýT You can change between t u o O z NORMAL, SHORT, and VERY SHORT using the TIME key. 5. Press the OK key to confirm the selection. The display changes to the symbol for DELAY START, i.e. DELAY START can now be set. 6. Press the TIME key, if no Delay Start is to be set. The display shows the TIME SAVING symbol as well as the time for the end of the cycle. Delay Start 1.
Starting a program 3 1. Check that the water tap is open. 2. Press the START/PAUSE key. The program is started or it starts after the time delay set has elapsed. If after pressing the START/PAUSE key the display shows “Door not Closed”, the door has not been shut properly. Push the door firmly closed and press the START/PAUSE key again. Program progress 3 The display indicates the stage of the program that is currently being performed as well as the time of the end of the program. 12.45 14.
– or turn the programme knob to OFF and then to SPIN. Change the spin speed if necessary and press the START/PAUSE key (the water is drained and the washing spun). Setup The special functions that can be set under Setup remain permanently stored independent of each washing cycle – even after the appliance has been switched off or the mains plug has been removed from the socket.
3 7. Press the OK key. The program combination is now stored to program knob position MEMORY 1 and in the future can be selected directly using the program knob. The Memory can be overwritten at any time with a new program combination (see “Changing the Memory”) but cannot be deleted. Changing the Memory 1. Put together the new program combination as required (for an example, see “Setting the Memory”, steps 1 to 4). 2. Press the OPTION key repeatedly, until the SETUP symbol flashes. 3. Press the OK key. 4.
Extra Rinse 1. Turn the program knob to any program and press the repeatedly until the SETUP symbol flashes. 2. Press the OK key. OPTION key 3. Press the OPTION key Rinse+ repeatedly until RINSE+ is shown in the NO aýýýýýaýaýaýaýBýaýaýaýa display. 4. Press the OK key. The RINSE+ t o O z u symbol appears. The display changes to the next special function. 5. Press the OPTION key repeatedly, until your program set appears again. Language 1.
Clock 1. Turn the program knob to any program and press the OPTION key repeatedly until the SETUP symbol flashes. 2. Press the OK key. 3. Press the OPTION key repeatedly until CLOCK is shown in the display. 4. Press the OK key. 5. Using the OPTION key 11.17 Clock set the desired time. With Set time each press of the key, the aýýýýýaýaýaýaýBýaýaýaýa display moves on by one minute. Keeping the key det u o O z pressed changes the display in 10 minute steps. 6. Press the OK key.
Child safety device When the child safety device is set, the door can no longer be closed. Setting the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go. 1 Warning! The knob must not be sunk-in after being set, otherwise the child safety device is not active. The knob must stand out as shown in the illustration. Releasing the child safety device: Turn the knob anti-clockwise as far as it will go.
Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place. 5. Clean all parts of the washing machine, especially the nozzles in the top of the washing-in chamber, with a brush. 6.
What to do if... Remedying small malfunctions yourself If while the appliance is operating a short acoustic signal sounds 3 times and one of the following messages appears in the display: – „No incoming water/Check tap & Hose“, – „No drain - check/drain hose/filter” or “Pump Blocked”, – “Door not Closed”, please have a look at the following table. When the fault is remedied, press the START/PAUSE key. If “Warning : E and number or letter” is displayed: Switch the appliance off and on again.
Problem Possible cause Transit packaging has not been removed. Washing machine vibrates when operating or is noisy. Screw feet not correctly adjusted. Washing has not been spun. Remedy Remove transit packaging. Adjust feet according to the Installation and Connection instructions. Always load the drum as full Only a few large items of as possible. Mix large and washing in the drum. small items. Screw connection on the Screw the inlet hose in firmly. inlet hose is leaking. Drain hose is leaking.
Problem Possible cause Door locked. Door cannot be opened when appliance is switched Power cut. (All displays are off.) on. For safety reasons, the door remains locked for approx. 4 to 10 minutes. Washing is heavily creased. Remedy Wait until the display shows “Door openable” and “Cycle ended” alternately. Program continues, when power cut is over. To remove washing: If water can be seen in the appliance, before opening the door, first perform an emergency drain.
Carrying out an emergency drain 1 Warning! Before emergency draining, switch off the washing machine and remove the mains plug from the socket. Warning! The water that comes out of the emergency drain hose may be hot. There is a risk of scalding. Let the water cool before performing an emergency drain. 1. Open the plinth flap and remove it. 2. Take out the emergency drain hose. 3. Place a shallow container underneath it.
Drain pump 1 The drain pump is maintenance-free. It is only necessary to open the pump cover if there is a malfunction and water is no longer being pumped out, e. g. if the pump wheel is blocked. Please make sure before loading the washing that there are no foreign bodies in the pockets or caught between the washing. Paperclips, nails, etc. that may have got into the washing machine with the washing remain in the pump housing (foreign body trap that protects the pump wheel).
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W 1 30 The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x Width x Depth 850 x 598 x 640 mm Depth when door is open 1017 mm Height adjustment approx. +10/-5mm Load (depending on programme) Max.
Installation and connection instructions 1 Safety information for the installation • This washing machine cannot be built-in. • Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. • Before using for the first time, all parts of the transport lock must be removed.
Installing the appliance Transporting the appliance 1 Warning! The washing machine is very heavy. Risk of injury. Be careful when lifting. • Do not lay the appliance on its front nor on its right side (as seen from the front). Electrical components may get wet. • Never transport the appliance without its transport lock. Only remove the transport lock when the appliance is in its place of installation. Transporting the appliance without its transport lock can lead to damage to the appliance.
2. Remove the power supply cable and the draining hose from the hose holders on the rear of the appliance. 3. With a suitable spanner unscrew and remove the central rear bolt A. Slide out the relevant plastic spacer. 4. Unscrew and remove the two large rear bolts B and the six smaller bolts C.
5. Remove the bracket D. 6. Refit the six smaller bolts C. 7. Open the porthole and remove the polystyrene block fitted with the adhesive tape on the door seal. 8. Fill the smaller upper hole and the two large ones with the corresponding plastic plug caps supplied in the bag containing the instruction booklet. Important! All the different plug caps are supplied with the appliance in the plastic bag containing the instruction booklet.
Connect the water inlet hose as described under the paragraph “Water inlet”. Where to install Important! The appliance must not be used in a room where there is a danger of frost. Frost damage or impaired operation! Frost damage is not covered by the warranty. • The surface on which the appliance is to be installed must be firm and level. Do not install the appliance on carpets or on soft floor coverings.
Connecting to the water supply Permitted water pressure The water pressure must be at least 1bar (=10N/cm2 =0.1MPa) and may be a maximum of 10bar (=100N/cm2 =1MPa). – If more than 10bar: Connect a pressure reduction valve. – If less than 1bar: Disconnect the appliance end of the inlet hose from the solenoid inlet valve and remove the flow meter. (In addition remove the filter using pointed pliers and take out the rubber gasket behind it.) Re-insert the filter.
4. Connect the hose to a tap with a 3/4” thread. Always use the hose supplied with the appliance. Installation should comply with local water authority and building regulations’ requirements. A minimum water pressure of 0.05 MPa (0.5 bar) is required for safe operation of the appliance. If you cannot make the cold water connection direct from the rising mains, you may be able to operate the appliance from your cold water storage system. There should be a minimum distance of 5.02m (16.
Water drainage The maximum permitted difference between the height of the surface on which the appliance is installed and the water outlet is 1 metre. Only original hoses may be used to extend hoses. (A maximum of 3 m laid on the floor and then 80 cm vertically). The Customer Care Department stocks outlet hoses of different lengths. Draining water into a sink outlet Secure the outlet/sink outlet joint with a hose band clip (available from your dealer).
Guarantee/Customer Service European Guarantee This appliance is guaranteed by Electrolux in each of the countries listed at the back of this user manual, for the period specified in the appliance guarantee or otherwise by law.
www.electrolux.com p t b Albania +35 5 4 261 450 Rr. Pjeter Bogdani Nr. 7 Tirane Belgique/België/ Belgien +32 2 363 04 44 Bergensesteenweg 719, 1502 Lembeek Èeská republika +420 2 61 12 61 12 Budìjovická 3, Praha 4, 140 21 Danmark +45 70 11 74 00 Sjællandsgade 2, 7000 Fredericia Deutschland +49 180 32 26 622 Muggenhofer Str. 135, 90429 Nürnberg Eesti +37 2 66 50 030 Mustamäe tee 24, 10621 Tallinn España +34 902 11 63 88 Carretera M-300, Km.
p t b Slovenija +38 61 24 25 731 Electrolux Ljubljana d.o.o. Gerbiceva 98, 1000 Ljubljana Slovensko +421 2 43 33 43 22 Electrolux Slovakia s.r.o., Electrolux Domáce spotrebièe SK, Seberíniho 1, 821 03 Bratislava Suomi www.electrolux.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
www.electrolux.