L 87485 FL L 87685 FL DE Benutzerinformation
www.aeg.com INHALT 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. SICHERHEITSINFORMATIONEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SICHERHEITSHINWEISE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 TECHNISCHE DATEN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 GERÄTEBESCHREIBUNG . . . . . . . . . . . . . . . . . . . .
DEUTSCH 3 1. SICHERHEITSINFORMATIONEN Lesen Sie vor der Montage und dem Gebrauch des Geräts zuerst die Gebrauchsanleitung. Der Hersteller übernimmt keine Verantwortung für Verletzungen und Beschädigungen durch unsachgemäße Montage. Bewahren Sie die Gebrauchsanleitung griffbereit auf. 1.1 Sicherheit von Kindern und schutzbedürftigen Personen WARNUNG! Es besteht Erstickungsgefahr, Risiko von Verletzungen oder permanenten Behinderungen.
www.aeg.com • Nehmen Sie keine technischen Änderungen am Gerät vor. • Beachten Sie die maximale Beladungsmenge von 8 kg (siehe Kapitel „Programmtabelle“). • Wenn das Netzkabel beschädigt ist, muss es vom Hersteller, seinem Kundenservice oder einer gleichermaßen qualifizierten Person ausgetauscht werden, um Gefahrenquellen zu vermeiden. • Der Betriebswasserdruck (Mindest- und Höchstdruck) muss zwischen 0,5 bar (0,05 MPa) und 8 bar (0,8 MPa) liegen.
DEUTSCH • • • • • • • chen. Wenden Sie sich andernfalls an eine Elektrofachkraft. Das Gerät darf ausschließlich an eine ordnungsgemäß installierte Schutzkontaktsteckdose angeschlossen werden. Verwenden Sie keine Mehrfachsteckdosen oder Verlängerungskabel. Achten Sie darauf, Netzstecker und Netzkabel nicht zu beschädigen. Falls das Netzkabel des Geräts ersetzt werden muss, lassen Sie dies durch unseren Kundendienst durchführen.
www.aeg.com 3. TECHNISCHE DATEN Abmessungen Breite / Höhe / Tiefe Elektrischer Anschluss: 600 / 850 / 605 mm Gesamttiefe 640 mm Spannung Gesamtleistung Sicherung Frequenz 230 V 2200 W 10 A 50 Hz Die Schutzverkleidung gewährleistet einen Schutz gegen das Eindringen von festen Fremdkörpern und Spritzwasser (Feuchtigkeit), außer an den Stellen, an denen das Niederspannungsgerät keinen Schutz gegen Feuchtigkeit besitzt. Wasserdruck IPX4 Min. 0,5 bar (0,05 MPa) Max.
DEUTSCH 5 Typenschild 9 Wassereinlassventil 6 Ablaufpumpe 7 Schraubfüße zum Ausrichten des Geräts 8 Wasserablaufschlauch 10 Netzkabel 7 11 Transportschrauben 12 Schraubfüße zum Ausrichten des Geräts 4.1 Zubehörteile 1 4 2 3 4.2 Einstellen der Kindersicherung • Bei aktivierter Kindersicherung lässt sich die Tür nicht schließen, damit Kinder oder Haustiere nicht in der Trommel eingeschlossen werden können.
www.aeg.com 5. BEDIENFELD 1 2 3 Glätten Koch/Bunt Auffrischen Baumwolle Eco Super Eco Extra Leise Pflegeleicht Leichtbügeln 20Min. - 3kg Feinwäsche Jeans Spülen Schleudern/ / Pumpen W Wolle/Seide Daunen Anti-Allergie Auto Off Temp. U./Min. Flecken/ Vorw. 10 9 8 1 Ein-/Aus-Taste (Auto Off) Extra Spülen 7 Zeit Sparen Zeitvorwahl 6 5 Start/Pause 4 10 Temperatur-Taste (Temp.
DEUTSCH 9 5.3 Display 3 A B C D L E K F G J H I Im Display erscheint: Die Temperatur des eingestellten Programms A Kaltes Wasser Die Schleuderdrehzahl des eingestellten Programms B Symbol Kein Schleudergang 1) Symbol Spülstopp 1) Nur verfügbar für das Programm Schleudern/Abpumpen. Vorwaschgang Hauptwaschgang Spülgänge Schleudergang C Phasensymbole • Wenn ein Programm ausgewählt wird, leuchten alle Symbole der im Programm vorkommenden Programmphasen auf.
www.aeg.com Das Türverriegelungssymbol erscheint, wenn das Programm beginnt. Sie können die Tür des Geräts nicht öffnen, solange dieses Symbol erscheint. Sie können die Tür erst öffnen, wenn das Symbol erlischt. F Wenn das Symbol nicht erlischt, obwohl das Programm beendet ist: • Die Spülstopp-Funktion ist eingeschaltet. • Es befindet sich Wasser in der Trommel. Das Zeitvorwahlsymbol leuchtet auf, wenn Sie die Funktion Zeitvorwahl eingestellt haben.
DEUTSCH 11 Der angezeigte Wert gibt die Gesamtanzahl der Spülgänge an. Der Anzeigebalken ist komplett gefüllt, wenn Sie die maximale Anzahl Spülgänge einstellen. Das Fleckensymbol leuchtet beim Aktivieren der Funktion auf. L Das Symbol für Vorwäsche leuchtet beim Aktivieren der Funktion auf. Der Anzeigebalken ist nicht ganz gefüllt, wenn Sie nur eine der Funktionen einstellen. Der Anzeigebalken ist vollständig gefüllt, wenn Sie beide Funktionen einstellen. 5.
www.aeg.com Das Display zeigt nur die Schleuderdrehzahlen an, die mit dem eingestellten Programm verfügbar sind. • Schalten Sie den Schleudergang aus. • Aktivieren Sie die Spülstopp-Funktion. Stellen Sie diese Funktion ein, um Knitterfalten zu vermeiden. Das Gerät pumpt das Wasser am Ende des Programms nicht ab. 5.10 Temperatur-Taste 10 Drücken Sie die Taste 10 zum Ändern der Standardtemperatur. Wenn das Display - - anzeigt, heizt das Gerät das Wasser nicht auf. 5.
DEUTSCH 13 6. ZUBEHÖR Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Koch/Bunt 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max. Beladung 8 kg Hauptwaschgang Spülgänge Langer Schleudergang DREHZAHLREDUZIERUNG SPÜLSTOPP VORWÄSCHE1) EXTRA SPÜLEN FLECKEN2) ZEIT SPAREN3) Extra Leise 95 °C - Kalt Weiße und bunte Baumwolle, normal verschmutzt. Max.
www.aeg.com Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen Daunen 60 - 30° Eine einzelne Decke aus Synthetik, Bettdecke, Bettlaken usw. Max. Beladung 2 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG Anti-Allergie 60° Weiße Baumwolle Dieses Programm beseitigt Mikroorganismen durch den Waschgang mit 60 °C und einem zusätzlichen Spülgang. Auf diese Weise wird die Reinigung effektiver.
DEUTSCH 15 Programm Temperatur Beladung Max. Beladung Programmbeschreibung Funktionen 20 Min. - 3kg 40° - 30° Teile aus Baumwolle oder Synthetik, die leicht verschmutzt sind oder nur einmal getragen wurden. Max. Beladung 3 kg Hauptwaschgang Spülgänge Kurzer Schleudergang DREHZAHLREDUZIERUNG Super Eco7) 0° Mischfasern (Baumwolle und Synthetik). Max.
www.aeg.com Dampf Auffrischen Dieses Programm beseitigt Gerüche aus der Wäsche. Baumwolle und Pflegeleicht bis zu 1.5 kg Dampf beseitigt keine Tiergerüche. Dampf Glätten Dieses Programm hilft bei der Beseitigung von Falten in der Wäsche. Baumwolle und Pflegeleicht bis zu 1.5 kg Dampf kann für getrocknete, gewaschene oder einmal getragene Wäsche benutzt werden. Diese Programme können Falten und Gerüche reduzieren und machen Ihre Wäsche glatter. Verwenden Sie kein Waschmittel.
DEUTSCH 17 7. VERBRAUCHSWERTE Am Programmstart zeigt das Display die Programmdauer für die maximale Beladung an. Während der Waschphase wird die Programmdauer automatisch berechnet und verringert sich möglicherweise beträchtlich, wenn die Wäsche weniger wiegt als die maximal zulässige Beladung. Zum Beispiel beträgt die maximale Beladung bei Baumwolle 60 °C 8 kg und die Programmdauer überschreitet 2 Stunden. Wiegt die tatsächliche Beladung 1 kg, verringert sich die Programmdauer auf unter 1 Stunde.
www.aeg.com Aus-Zustand (W) Ein-Zustand (W) 0.05 0.05 Die in den Tabellen oben enthaltenen Informationen erfüllen die Verordnung (EG) der Kommission zur 1015/2010 Anwendung der Richtlinie 2009/125/EC. 8. VOR DER ERSTEN INBETRIEBNAHME 1. Zum Aktivieren des Ablaufsystems füllen Sie 2 Liter Wasser in das Hauptfach der Waschmittelschublade. 2. Geben Sie eine kleine Waschmittelmenge in das Hauptfach der Waschmittelschublade.
DEUTSCH 19 Waschmittelfach für die Vorwaschphase und das Einweichprogramm. Füllen Sie das Waschmittel für den Vorwaschgang und das Einweichen vor dem Start des Programms ein. Waschmittelfach für die Waschphase. Wenn Sie Flüssigwaschmittel verwenden, muss dieses direkt vor dem Start des Programms eingefüllt werden. Fach für flüssige Pflegemittel (Weichspüler, Stärke). Füllen Sie das Pflegemittel in das Fach ein, bevor Sie das Programm starten. Das ist die maximale Menge für flüssige Pflegemittel.
www.aeg.com 3. Drehen Sie die Klappe nach oben, wenn Sie Waschpulver verwenden. 4. Drehen Sie die Klappe nach unten, wenn Sie Flüssigwaschmittel verwenden. Klappe in der Position „Unten“: – Verwenden Sie keine Gelwaschmittel oder Flüssigwaschmittel mit dicker Konsistenz. – Füllen Sie nicht mehr Flüssigwaschmittel ein als bis zur Markierungslinie auf der Klappe. – Stellen Sie nicht den Vorwaschgang ein. – Stellen Sie nicht die Zeitvorwahl ein. 5. 6. Messen Sie Waschmittel und Weichspüler ab.
DEUTSCH 21 9.4 Unterbrechen eines Programms 9.8 Abbrechen der Zeitvorwahl 1. Drücken Sie die Taste 4 . Die Kontrolllampe blinkt. 1. Drücken Sie die Taste 4 . Die zugehörige Kontrolllampe blinkt. 2. Drücken Sie die Taste 4 erneut. Das Waschprogramm wird fortgesetzt. 2. Drücken Sie die Taste 5 wiederholt, bis das Display 0’ anzeigt. 3. Drücken Sie die Taste 4 . Das Programm startet. 9.5 Abbrechen eines Programms 9.9 Öffnen der Tür 1.
www.aeg.com 10. AM PROGRAMMENDE • Das Gerät stoppt automatisch. • Es ertönen akustische Signale. • Im Display erscheint . • Die Kontrolllampe der Start/PauseTaste 4 erlischt. • Das Türverriegelungssymbol erlischt. • Drücken Sie die Taste 1 , um das Gerät auszuschalten. Fünf Minuten nach Ende des Programms schaltet die Energiesparfunktion das Gerät automatisch aus. Wenn Sie das Gerät wieder einschalten, sehen Sie im Display das Ende des letzten Programms.
DEUTSCH 11.2 Hartnäckige Flecken Für manche Flecken sind Wasser und Waschmittel nicht ausreichend. Wir empfehlen, diese Flecken zu entfernen, bevor Sie die entsprechenden Textilien in das Gerät geben. Spezial-Fleckentferner sind im Handel erhältlich. Verwenden Sie einen SpezialFleckentferner, der für den jeweiligen Fleckentyp und Gewebetyp geeignet ist. 11.3 Wasch- und Pflegemittel • Verwenden Sie nur speziell für Waschmaschinen bestimmte Wasch- und Pflegemittel.
www.aeg.com 12.2 Reinigen der Außenseiten Reinigen Sie das Gerät nur mit warmem Wasser und mit etwas Spülmittel. Reiben Sie alle Oberflächen sorgfältig trocken. VORSICHT! Verwenden Sie keinen Alkohol, keine Lösungsmittel und keine Chemikalien. 12.3 Waschgang zur Pflege der Maschine Bei Waschprogrammen mit niedrigen Temperaturen kann etwas Waschmittel in der Trommel zurückbleiben. Führen Sie regelmäßig einen Waschgang zur Pflege der Maschine durch: • Entnehmen Sie die Wäsche aus der Trommel.
DEUTSCH 3. 4. 5. 6. 25 Entfernen Sie den oberen Teil des Pflegemittelfachs. Reinigen Sie alle Teile mit Wasser. Reinigen Sie das leere Einschubfach mit einer Bürste. Schieben Sie die Waschmittelschublade wieder in das Einschubfach ein. WARNUNG! 1. Ziehen Sie den Netzstecker aus der Netzsteckdose. 2. Entfernen Sie den Filter nicht, während das Gerät in Betrieb ist. Reinigen Sie die Ablaufpumpe nicht, wenn das Wasser im Gerät heiß ist. Das Wasser muss abgekühlt sein, bevor Sie die Ablaufpumpe reinigen.
www.aeg.com 3. 4. 5. 1 6. 2 2 1 12.8 Zulaufschlauchfilter und Ventilfilter Die Filter müssen in folgenden Fällen gereinigt werden: • Es läuft kein Wasser in das Gerät. • Das Wasser läuft sehr lange in das Gerät ein. Stellen Sie einen Behälter unter die Ablaufpumpe, um das auslaufende Wasser aufzufangen. Drücken Sie die zwei Hebel und ziehen Sie den Ablaufkanal nach vorn, um das Wasser auslaufen zu lassen.
DEUTSCH 27 So reinigen Sie die Wasserzulauffilter: Schließen Sie den Wasserhahn. Entfernen Sie den Wasserzulaufschlauch vom Wasserhahn. 3. Reinigen Sie den Filter im Zulaufschlauch mit einer harten Bürste. 1. 2. 4. 5. 6. 20° 45° 7. Entfernen Sie den Zulaufschlauch von der Geräterückseite. Reinigen Sie den Filter im Ventil mit einer harten Bürste oder einem Handtuch. Bringen Sie den Zulaufschlauch wieder an.
www.aeg.com WARNUNG! Vergewissern Sie sich vor einer erneuten Benutzung des Geräts, dass die Temperatur mehr als 0 °C beträgt. Der Hersteller ist nicht verantwortlich für Schäden, die durch niedrige Temperaturen entstanden sind. 13. PROGRAMME Das Gerät startet nicht oder stoppt während des Betriebs. Versuchen Sie zunächst eine Lösung für das Problem zu finden (siehe Tabelle). Wenn Sie keine Lösung finden, wenden Sie sich an den Kundendienst. • - Das Gerät pumpt das Wasser nicht ab.
DEUTSCH Problem Mögliche Ursache Mögliche Abhilfe Der Wasserablaufschlauch ist nicht richtig angeschlossen. Vergewissern Sie sich, dass die Schlauchverbindung in Ordnung ist. Ein Waschprogramm ohne Abpumpphase ist eingestellt. Stellen Sie das Abpumpprogramm ein. Die Funktion Spülstopp ist aktiviert. Stellen Sie das Abpumpprogramm ein. 29 Die Gerätetür steht offen oder ist nicht richtig geschlossen. Schließen Sie die Tür richtig. Die Aquasafe-Einrichtung ist aktiv. • Schalten Sie das Gerät aus.
www.aeg.com Problem Mögliche Ursache Mögliche Abhilfe Der Wasserablaufschlauch ist beschädigt. Vergewissern Sie sich, dass der Wasserzulaufschlauch nicht beschädigt ist. Die Tür des GeEin Waschprogramm räts lässt sich nicht läuft. öffnen. Warten Sie das Ende des Waschprogramms ab. Es befindet sich Wasser in der Trommel. Stellen Sie das Abpump- oder Schleuderprogramm ein. Das Gerät ist nicht ausgerichtet. Richten Sie das Gerät waagrecht aus. Siehe hierzu „Montage“.
DEUTSCH 31 14. MONTAGE 14.1 1 Satz Fixierplatten (4055171146) Sie erhalten den Bausatz bei Ihrem Vertragshändler. Wenn Sie das Gerät auf einem Sockel aufstellen, befestigen Sie es mithilfe der Fixierplatten. Lesen Sie aufmerksam die dem Bausatz beiliegende Anleitung. 14.2 Auspacken 1. Verwenden Sie Handschuhe. Entfernen Sie die äußere Folie. Benutzen Sie, falls erforderlich, ein Teppichmesser. 2. Nehmen Sie die Karton-Abdeckung ab. Entfernen Sie die Styropor-Verpackungsteile. 3. 4.
www.aeg.com 5. Öffnen Sie die Tür. Entfernen Sie das Styroporteil aus der Türdichtung und alle Teile aus der Trommel. 6. Legen Sie eines der Styroporverpackungsteile hinter dem Gerät auf den Boden. Legen Sie das Gerät vorsichtig mit der Rückseite darauf ab. Achten Sie darauf, die Schläuche nicht zu beschädigen. 7. Entfernen Sie den Styroporschutz von der Geräteunterseite. Ziehen Sie das Gerät nach oben, sodass es wieder aufrecht steht. 8. 1 2 9.
DEUTSCH 33 10. Lösen Sie die drei Schrauben. Ver- wenden Sie dazu den mitgelieferten Schraubenschlüssel. 11. Ziehen Sie die Kunststoff-Abstandshalter heraus. 12. Setzen Sie die Kunststoffkappen in die Öffnungen. Diese Kappen finden Sie im Beutel mit der Gebrauchsanleitung. WARNUNG! Entfernen Sie vor der Montage des Geräts alle Verpackungsmaterialien und Transportschrauben. Wir empfehlen, Verpackungsmaterial und Transportschrauben für einen späteren Transport aufzubewahren. 14.
www.aeg.com • Das Gerät muss einen waagerechten und festen Stand haben. VORSICHT! Schieben Sie weder Karton noch Holz oder ähnliche Materialien unter die Stellfüße, um das Gerät auszurichten. 14.4 Wasserzulaufschlauch • Schließen Sie den Schlauch am Gerät an. Drehen Sie den Wasserzulaufschlauch nur nach links oder rechts. Lösen Sie die Ringmutter, um ihn in die gewünschte Position zu bewegen.
DEUTSCH 35 Aquastopp-Einrichtung A Der Zulaufschlauch verfügt über eine Wasserstopp-Vorrichtung. Damit werden Wasserlecks am Schlauch, die durch natürliche Alterung auftreten könnten, verhindert. Der rote Bereich im Fenster „A“ zeigt diesen Fehler an. Tritt dieser Fall ein, drehen Sie den Wasserhahn zu und wenden Sie sich an den Kundendienst, um den Schlauch zu erneuern. 14.5 Wasserablauf Es gibt mehrere Möglichkeiten, den Ablaufschlauch anzuschließen: Mit der Kunststoff-Schlauchführung.
www.aeg.com Ohne Kunststoff-Schlauchführung. • An einen Siphon. Orientieren Sie sich an der Abbildung. Stecken Sie den Ablaufschlauch in den Siphon und befestigen Sie ihn mit einer Schlauchschelle. Stellen Sie sicher, dass der Schlauch einen Bogen beschreibt, damit kein Schmutz aus dem Siphon in das Gerät gelangen kann. • Direkte Einleitung in ein Abflussrohr in der Zimmerwand. Mit einer Schlauchschelle befestigen. Sie können den Ablaufschlauch auf maximal 400 cm verlängern.
DEUTSCH 37
www.aeg.
DEUTSCH 39
132942354-A-392012 www.aeg.