L 98485 FL L 98685 FL EN User manual
www.aeg.com CONTENTS 1. 2. 3. 4. 5. 7. 8. 9. 10. 11. 12. 13. 14. SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 TECHNICAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . .
ENGLISH 3 1. SAFETY INFORMATION Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com 2.1 Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance. • Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
ENGLISH • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. • Do not use water spray and steam to clean the appliance. • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. 5 • Disconnect the appliance from the mains supply. • Cut off the mains cable and discard it. • Remove the door catch to prevent children and pets to get closed in the appliance. 2.
www.aeg.com 4. PRODUCT DESCRIPTION 1 2 3 9 10 11 4 5 6 12 7 13 8 1 Worktop 9 Water drain hose 2 Detergent dispenser 3 Control panel 10 Water inlet hose 4 Door handle 12 Transit bolts 5 Internal lamp 13 Feet for the appliance level 11 Mains cable 6 Rating plate 4.1 Interior accessories 7 Drain pump 8 Feet for the appliance level 1 2 1 Spanner To remove the transit bolts. 2 Plastic caps 4 3 To close the holes on the rear side of the cabinet after the removal of the transit bolts.
ENGLISH 7 5. CONTROL PANEL 1 2 3 Ontkreuk Katoen Opfrissen Extra Stil Eco Fijne Was Jeans Geheugen 2 Wol/Zijde Dekbed Auto Off Anti-Allergie 4 Geheugen 1 Strijkvrij 20 Min. - 3 kg Spoelen Centrifugeren/ Pompen Stoom Synthetica Super Eco Temp.°C TPM 12 11 Vlekken/ Extra Tijd Voorw.
www.aeg.com 6.4 Display 3 A J A I B H G C F D E The text bar: • Guides you in the use of the appliance. • Shows the programme status and phase. • Shows alarm messages. Refer to 'Troubleshooting' . The symbols appear on the display when the related phase or function is set. B Child lock C Door locked You cannot open the door when the symbol is on. You can open the door only when the symbol goes off. If the symbol stays on but the programme is completed: • There is water in the drum.
ENGLISH 9 • The time of delay – When you set the delayed start the time of the programme end increases by steps of 30 minutes till 10 hours and by steps of one hour till 20 hours. • The end of the programme The display shows a zero. This part comes on only if the door is open - Refer to 'Loading the laundry'. The programme maximum load The weight of the laundry E The indicator bar fills accordingly to the laundry weight. The indicator fully fills when you put the maximum load.
www.aeg.com Rinse hold 1) Only available for Spin/Drain programme. The default temperature of the programme. J Cold wash 6.5 STOOM BUTTON 4 Touch button 4 to set the steam level. This is possible only with programmes where the steam function is available. The duration of the steam phase changes accordingly to your selection. 6.6 GEHEUGEN BUTTONS 5 Touch one of the buttons 5 to memorise a programme or to set a memorised programme. Memorise a programme 1. Press button 1 to activate the appliance. 2.
ENGLISH VOORWAS Use this function for heavy soil. The appliance adds a prewash phase to the main wash. The programme duration increases. INWEKEN Use this function for heavy soil. The appliance soaks the laundry at 30°C for about half an hour before to wash. 6.12 SPIN BUTTON 11 Touch button 11 to: • Decrease the maximum speed of the spin phase of the programme. The display shows only the spin speeds available with the set programme. • Deactivate the spin phase (' No Spin ' function).
www.aeg.com 7. WASHING PROGRAMMES Programme Temperature Type of load Weight of load Programme description Katoen 95° - Cold White and colWash oured cotton Rinses with heavy level Long spin of soil. Maximum load 8 kg SPIN REDUCTION SPOELSTOP VLEKKEN1) VOORWAS2) INWEKEN EXTRA SPOELEN TIJD BESPAREN3) Extra Stil 95° - Cold White and coloured cotton with normal level of soil.
ENGLISH Programme description 13 Programme Temperature Type of load Weight of load Fijne Was 40° - Cold Rinses Short spin Delicate fabrics Wash as acrylics, visRinses cose, polyester Short spin items with normal soil. Maximum load 4 kg SPIN REDUCTION SPOELSTOP VOORWAS2) VLEKKEN1) INWEKEN EXTRA SPOELEN TIJD BESPAREN3) Wol / Zijde 40° - Cold Rinses Short spin Machine washa- Wash ble wool as well Rinses as for hand Short spin washable woollens and delicate fabrics with «hand washing» care symbol.
www.aeg.com Programme Temperature Type of load Weight of load Programme description Functions Jeans 60° - Cold Items like pants, Wash shirts or jackets Rinses in Jeans and al- Long spin so jersey realized with hi-tech materials. Maximum load 8 kg SPIN REDUCTION SPOELSTOP VOORWAS2) INWEKEN EXTRA SPOELEN TIJD BESPAREN3) 20 min. - 3 kg 40° or 30° Quick wash of Wash sport items or Rinses cotton and syn- Short spin thetic items, lightly soiled or worn once.
ENGLISH 15 C cotton programme” and the “standard 40° C cotton programme”. They are the most efficient programmes in terms of combined energy and water consumption for washing normally soiled cotton laundry. The water temperature of the washing phase may differ from the temperature declared for the selected programme. 10) Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended.
www.aeg.com Programmes Load (kg) Energy consumption (kWh) Water Approxi- Remain- Remainconsumpmate ing ing tion (litre) promoisture moisture gramme (%)1) (%)1) duration L 98485 L 98685 (minutes) FL FL Delicates 40 °C 4 0.70 58 91 35 35 Wool/ Hand wash 30 °C 2 0.35 57 56 30 30 Standard cotton programmes Standard 60 °C cotton 8 0.89 60 223 52 44 Standard 60 °C cotton 4 0.74 37 190 52 44 Standard 40 °C cotton 4 0.49 37 171 52 44 1) At the end of spin phase.
ENGLISH 17 The first time you activate the appliance, the display shows the default language and tells you to confirm it or change it: • Turn the programme knob to set the desired language. • When the display shows the necessary language, touch button 6 to confirm the selection. • Turn the programme knob to change the hour. • Touch button 6 to confirm the selection. • The minute digits flash. • Turn the programme knob to change the minutes. • Touch button 6 to confirm the selection.
www.aeg.com 3. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. 4. On the display the weight of the laundry updates by step of kg 0.5. The weight is indicative and changes with the type of the laundry. 5. Close the door. The text bar on the display tells the percentage of detergent to use. This data is indicative and refers to the detergent quantity for a maximum load that the manufacturer recommends.
ENGLISH 19 The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme. This is the maximum level for the quantity of liquid additives. The compartment for the stain remover. Put the product in the compartment and set the stain function before you start the programme.
www.aeg.com 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser. Make sure that the flap does not cause a blockage when you close the drawer. 9.4 Set the delay start 1.
ENGLISH 1. Touch button 6 . The indicator flashes. 2. Change the function set. 3. 4. 5. 6. Touch button 6 again. The washing programme continues. 9.9 Open the door To open the appliance door: 1. If the temperature and the level of the water is too high, the door lock symbol stays on. You cannot open the door. If necessary, do the following procedure to open the door: 1. Deactivate the appliance. 2. Wait for some minutes. 3. Make sure that no water is in the drum.
www.aeg.com • • • • • • • • that you wash them separately for the first times. Button up pillowcases, close zippers, hooks and poppers. Tie up belts. Empty the pockets and unfold the items. Turn inside out multilayered fabrics, wool and items with painted illustrations. Remove hard stains. Wash with a special detergent heavy soil stains. Be careful with the curtains. Remove the hooks or put the curtains in a washing bag or pillowcase.
ENGLISH 23 11. CARE AND CLEANING WARNING! Disconnect the appliance from the mains supply before you clean it. 11.1 Descaling The water we use contains limescale. If it becomes necessary, use a water softener to remove limescales. Use a special product made for washing machines. Obey the instructions that you find on the packaging of the manufacturer. Do this separately from the laundry wash. 11.2 External cleaning CAUTION! Do not use alcohol, solvents or chemical products. 11.
www.aeg.com 11.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever. Pull the dispenser out. 3. Remove the top part of the liquid additive compartment. Clean all the parts with water. 2 4. 5. 6. 11.7 Drain pump Regularly examine the drain pump and make sure that it is clean. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn. • The appliance makes an unusual noise because of the blockage of the drain pump.
ENGLISH 25 To clean the drain pump: 1. Open the drain pump door. 2. Pull the flap out to remove it. 3. Put a container below the recess of the drain pump to collect the water that flows out. Press the two levers and pull forward the drainage duct to let the water flow out. 4. 1 5. 6. When the container is full of water, put the drainage duct back again and empty the container. Do steps 4 and 5 again and again until no more water flows out from the drain pump.
www.aeg.com 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door. 2 1 11.8 The inlet hose filter and the valve filter • The indicator of button 6 flashes and the display shows the related alarm. Refer to 'Troubleshooting'. It could be necessary to clean the filters when: • The appliance does not fill with water.
ENGLISH Put the drainage duct back and close the drain pump flap. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. 27 2. 3. 4. Close the water tap. Remove the water inlet hose Put the two ends of the inlet hose in a container and let the water flow out of the hose. 5. Empty the drain pump.
www.aeg.com Problem Possible cause The display tells The water drain hose is to check the damaged. drain filter: the appliance does not drain the water. Possible solution Make sure that the water drain hose has no damages. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. The connection of the water drain hose is not correct. Make sure that the connection is correct. The display tells to check the door.
ENGLISH Problem 29 Possible cause Possible solution The Child Lock function is activated. Deactivate the Child Lock function. There is water on Leakages from the couthe floor. plings of the water hoses. Make sure that the couplings are tight. Leakages from the drain Make sure that the drain pump pump. filter is tight. You cannot open the appliance door. The water drain hose is damaged. Make sure that the water inlet hose has no damages. The washing programme is in operation.
www.aeg.com Problem Possible cause After a steam programme, garments are not sufficiently smooth. A wrong STEAM proNote the composition of the gramme has been selec- fabric. ted (e.g. Synthetic instead of Cotton). Possible solution Excessive laundry load. Reduce the laundry load The drum is emp- It is necessary to set a ty and the distare. play shows there is some weight in . Press button 1 to deactivate the appliance and to activate it again. The drum is full but the display shows 0.0 kg.
ENGLISH 31 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum. 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses.
www.aeg.com 7. 8. Remove the polystyrene protection from the bottom. Pull up the appliance in vertical position. 1 2 9. Remove the power supply cable and the drain hose from the hose holders. 10. Remove the three bolts. Use the key supplied with the appliance. 11. Pull out the plastic spacers. 12. Put the plastic caps in the holes. You can find these caps in the user manual bag.
ENGLISH WARNING! Remove all the packaging and the transit bolts before you install the appliance. 33 We recommend that you keep the packaging and the transit bolts for when you move the appliance. 13.3 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance. • Make sure that the appliance does not touch the wall or other units • Loosen or tighten the feet to adjust the level.
www.aeg.com • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device. This device prevents water leaks in the hose because of its natural ageing. The red sector in the window «A» shows this fault .
ENGLISH 35 • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose. Without the plastic hose guide.
www.aeg.com 14. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste. Return the product to your local recycling facility or contact your municipal office.
ENGLISH 37
www.aeg.
ENGLISH 39
132940562-A-222012 www.aeg.