L98699 FL2 EN User manual
www.aeg.com CONTENTS 1. 2. 4. 5. 6. 8. 9. 10. 11. 18. 19. 20. 21. 22. SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 INTERIOR ACCESSORIES . . . . . . . . . . . . . .
ENGLISH 1. 3 SAFETY INSTRUCTIONS Before the installation and use of the appliance, carefully read the supplied instructions. The manufacturer is not responsible if an incorrect installation and use causes injuries and damages. Always keep the instructions with the appliance for future reference. 1.1 Children and vulnerable people safety WARNING! Risk of suffocation, injury or permanent disability.
www.aeg.com 2.1 Installation • Remove all the packaging and the transit bolts. • Keep the transit bolts. When you move the appliance again you must block the drum. • Do not install or use a damaged appliance. • Do not install or use the appliance where the temperature is less than 0 °C or where it is exposed to the weather. • Obey the installation instruction supplied with the appliance. • Make sure that the floor where you install the appliance is flat, stable, heat resistant and clean.
ENGLISH • Before maintenance, deactivate the appliance and disconnect the mains plug from the mains socket. • Do not use water spray and steam to clean the appliance. • Clean the appliance with a moist soft cloth. Only use neutral detergents. Do not use abrasive products, abrasive cleaning pads, solvents or metal objects. 2.4 Internal light WARNING! Risk of injury. Visible LED radiation, do not look directly into the beam. 5 To replace the internal light, contact the Service. 2.
www.aeg.
ENGLISH 5 Internal lamp 10 Water inlet hose 6 Rating plate 7 Drain pump 11 Mains cable 8 Feet for the appliance level 13 Feet for the appliance level 7 12 Transit bolts 9 Water drain hose 5. INTERIOR ACCESSORIES 1 1 Spanner 2 To remove the transit bolts. 2 Plastic caps 5 4 To close the holes on the rear side of the cabinet after the removal of the transit bolts. 3 Sound barrier To decrease the noise while the appliance operates.
www.aeg.com 6 Start/Pause touch button ( Start/ 10 Pause ) 7 8 9 Delay start touch button Time save touch button (Time Save) – Shortened duration ( Shortened duration ) – Extra Quick duration ( Extra quick ) Extra rinse touch button rinsing ) 11 12 Option touch button / – Anti stains ( Stains ) – Prewash phase ( Prewash ) – Soak phase ( Soak ) Spin reduction touch button ( Spin speed ) Temperature touch button ( Temperature ) ( Extra 7.
ENGLISH 9 The symbols appear on the display when the related phase or function is set. B Child lock C Door locked You cannot open the door when the symbol is on. You can open the door only when the symbol goes off. If the symbol stays on but the programme is completed: • There is water in the drum. • The ' Rinse Hold ' function is on. • The time of the day When you activate the appliance the display shows the time of the day for some seconds. To adjust the clock, refer to "Clock setting".
www.aeg.com • If you make an incorrect selection the text bar on the display tells that the selection is not possible. Time save The symbol comes on when you set the following functions: F Shortened duration Extra quick Extra rinsing G The indicator bar fills accordingly the numbers of rinses. Stains Prewash H Soak The indicator bar fills accordingly to the set functions. The default spin speed of the programme. I ___ No spin 1) Rinse hold 1) Only available for Spin/Drain programme.
ENGLISH 7.7 START PAUSE BUTTON 6 The programme duration increases. Touch button 6 to start or interrupt a programme. SOAK 7.8 DEALY START BUTTON 7 Touch button 7 to delay the start of a programme from 30 minutes to 20 hours. 7.9 TIME SAVE BUTTON 8 Touch button 8 to decrease the programme time. You can select: SHORTENED DURATION To wash items with daily soil. EXTRA QUICK To wash quickly items with almost no soil. Some programmes accept only one of these functions. 7.
www.aeg.com • To activate the function, touch button 12 and button 11 at the same time until the display shows the symbol . • To deactivate the function, touch button 12 and button 11 at the same time until the symbol goes off. You can activate the function: • Before you touch the button 6 : the appliance cannot start. • After you touch the button 6 , all the buttons and the programme knob are deactivated.
ENGLISH Programme Temperature Type of load Weight of load 60° - Cold Synthetic fabric Wash items with norRinses mal soil. It preShort spin vents the creases of the laundry. Maximum load 4 kg Spin Reduction Rinse hold Prewash2) Soak Extra rinse Time save3) 40° - Cold Rinses Short spin Delicate fabrics as acrylics, viscose, polyester items with normal soil.
www.aeg.com Programme Temperature Type of load Weight of load Programme description Functions 60° - Cold Waterproof, sports and outdoor clothing. Do not use any fabric softener! Maximum load 2.5 kg Wash Rinses Short spin Spin Reduction Rinse hold Extra rinse 20 Min. - 3 kg 40° or 30° Quick wash of sport items or cotton and synthetic items, lightly soiled or worn once. Maximum load 3 kg Wash Rinses Short spin Spin Reduction Super Eco 0° Mixed fabrics (cotton and synthetic items)8).
ENGLISH 15 The washing temperature of the washing phase may differ from the temperature declared for the selected programme. 10) Set this programme to have a good washing results and decrease the energy consumption. The time of the washing programme is extended. STEAM PROGRAMMES Programme1) Type of load Load Steam Refresh2) This cycle removes odour from the laundry. Cotton and synthetic items. up to 1.5 Kg Cotton and synthetic items. up to 1.5 Kg Steam does not remove animal odours.
www.aeg.com 9. CONSUMPTION VALUES The data of this table are approximate. Different causes can change the data: the quantity and type of laundry, the water and ambient temperature. Programmes Load (Kg) Energy con- Water consumption sumption (li(kWh) tre) Approximate programme duration (minutes) Remaining moisture (%)1) Cottons 60 °C 9 1.60 69 179 43 Cottons 40 °C 9 1.00 69 175 43 Synthetics 40 °C 4 0.60 48 170 00 Delicates 40 °C 4 0.70 58 91 00 Wool/Hand wash 30 °C 2 0.
ENGLISH Change the language after the first activation 1. Touch button 11 and button 10 at the same time for some seconds. 2. When display shows the language set, turn the programme knob to set the new language. 3. Touch button 6 to confirm the selection. 10.2 Clock setting After you set the language, the display tells to set the clock: • The hour digits flash. • Turn the programme knob to change the hour. • Touch button 6 to confirm the selection. • The minute digits flash.
www.aeg.com 13. LOADING THE LAUNDRY Open the appliance door. The display (E) shows the maximum programme load for the programme (MAX ) and the weight of the laundry (KG). The text bar on the display tells to add the laundry. 3. Put the laundry in the drum, one item at a time. Shake the items before you put them in the appliance. 4. On the display the weight of the laundry updates by step of kg 0.5. The weight is indicative and changes with the type of the laundry. 1. 2. 5. Close the door.
ENGLISH 19 14. FILLING THE DETERGENT AND ADDITIVES The detergent compartment for the prewash phase and the soak programme. Add the detergent for prewash and soak before the start of the programme. The detergent compartment for the washing phase. If you use a liquid detergent, put it immediately before you start the programme. Liquid additives compartment (fabric conditioner, starch). Put the product in the compartment before you start the programme.
www.aeg.com 3. To use powder detergent, turn the flap up. 4. To use liquid detergent, turn the flap down. With the flap in the position DOWN: – Do not use gelatinous or thick liquid detergents. – Do not put more liquid detergent than the limit showed in the flap. – Do not set the prewash phase. – Do not set the delay start function. 5. 6. Measure out the detergent and the fabric conditioner. Carefully close the detergent dispenser.
ENGLISH The appliance adjust automatically the cycle time to the laundry you have put in the drum to have perfect washing results in the minimum necessary time. After approximately 15 minutes from the start of the programme, the display shows the new time value. 2. 3. 21 Change the function set. Touch button 6 again. The washing programme continues. 16.4 Open the door While a programme or the delay start operates, the appliance door is locked. To open the appliance door: 1. 16.
www.aeg.com The washing programme is completed, but there is water in the drum: – The drum turns regularly to prevent the creases in the laundry. – The door stays locked. – You must drain the water to open the door. To drain the water: 1. If necessary, decrease the spin speed. 2. Touch button 6 . The appliance drains the water and spins. 3. When the programme is completed and the door lock symbol goes off, you can open the door 4. Press button 1 to deactivate the appliance.
ENGLISH chines. In areas where the water hardness is soft it is not necessary to use a water softener. To know the water hardness in your area, contact your local water authority. Obey the instructions that you find on the packaging of the products. Equivalent scales measure the water hardness: 23 • German degrees (°dH). • French degrees (°TH). • mmol/l (millimol for each litre - international unit for the hardness of water). • Clarke degrees. Water hardness table Level Type Water hardness °dH °T.H.
www.aeg.com 19.4 Door seal Regularly examine the seal and remove all objects from the inner part. 19.5 Drum Regularly examine the drum to prevent limescale and rust particles. Only use special products to remove rust particles from the drum. To do this: • Clean the drum with special product for stainless steel. • Start a short programme for cotton at the maximum temperature with a small quantity of detergent. 19.6 Detergent dispenser To clean the dispenser: 1 1. 2. Press the lever.
ENGLISH 19.7 Drain pump Regularly examine the drain pump and make sure that it is clean. 25 • The display shows an alarm code because of the problem with water drain. WARNING! 1. Disconnect the mains plug from the mains socket. 2. Do not remove the filter while the appliance operates. Do not clean the drain pump if the water in the appliance is hot. The water must be cold before you clean the drain pump. Clean the pump if: • The appliance does not drain the water. • The drum cannot turn.
www.aeg.com 2 1 19.8 The inlet hose filter and the valve filter 7. Remove fluff and objects from the pump. 8. Make sure that the impeller of the pump can turn. If this does not occur, contact the service centre. 9. Clean the filter under the water tap and put it back in the pump into the special guides. 10. Make sure that you tighten correctly the filter to prevent leakages. 11. Put the flap back and close the drain pump door.
ENGLISH 4. 5. 6. 7. 20° 27 Remove the inlet hose behind the appliance. Clean the filter in the valve with a stiff brush or a towel. Install again the inlet hose. Make sure that the couplings are tight to prevent leakages. Open the water tap. 45° 19.9 Emergency drain Because of a malfunction, the appliance cannot drain the water. If this occurs, do steps (1) through (6) of 'To clean the drain pump'. If necessary, clean the pump. Put the drainage duct back and close the drain pump flap.
www.aeg.com Problem Possible cause The display tells The water tap is closed. to check the tap: the appliance does not fill with water. Possible solution Open the water tap. The water inlet hose is damaged. Make sure that the water inlet hose has no damages. The filters in the water inlet hose is blocked . Clean the filters. Refer to 'Care and cleaning'. The connection of the water inlet hose is not correct. Make sure that the connection is correct. The water pressure is too low.
ENGLISH 29 Problem Possible cause Possible solution The spin phase does not operate. The spin phase is off. Set the spin programme. The filter of the drain pump is blocked. Clean the filter of the drain pump. Refer to 'Care and cleaning'. Balance problems with the laundry load. Adjust manually the items in the tub and start the spin phase again. The mains plug is not connected in the mains socket. Put in the mains plug. Blow out fuse in the household fuse box. Replace the fuse.
www.aeg.com Problem Possible cause The washing results are not satisfactory. The detergent you used Increase the detergent quantity was not sufficient or cor- or use a different one. rect. Possible solution You did not remove the stubborn stains before you wash the laundry. Use special products to remove the stubborn stains. You set a not correct temperature. Make sure that you set the correct temperature. Too much laundry load. Decrease the laundry load. The internal lamp The lamp is burned.
ENGLISH 31 21. INSTALLATION 21.1 Unpacking 1. Use the gloves. Remove the external film. If necessary, use a cutter. 2. 3. Remove the cardboard top. Remove the polystyrene packaging materials. 4. Remove the internal film. 5. Open the door. Remove the polystyrene piece from the door seal and all the items from the drum.
www.aeg.com 6. Put one of the polystyrene packaging elements on the floor behind the appliance. Carefully put down the appliance with the rear side on it. Make sure not to damage the hoses. 7. Remove the polystyrene protection from the bottom. 8. Fully clean and dry the bottom of the appliance. Do not use alcohol, solvents or chemical products. 9. Make sure to identify the different sizes and the positions of the sound barriers.
ENGLISH 33 10. – Remove the adhesive strip from x4 A the silent barriers. – Attach the four barriers to bottom of the appliance. Refer to the illustration. – Make sure that the barriers are securely attached. Attach the sound barriers at a room temperature. B 11. Pull up the appliance in vertical po- sition. 12. Remove the power supply cable and the drain hose from the hose holders. 13. Turn the three bolts with the key supplied with the appliance. Pull out the plastic spacers.
www.aeg.com 14. Put the plastic caps in the holes. You can find these caps in the user manual bag. WARNING! Remove all the packaging and the transit bolts before you install the appliance. We recommend that you keep the packaging and the transit bolts for when you move the appliance. 21.2 Positioning and levelling • Install the appliance on a flat hard floor. • Make sure that carpets do not stop the air circulation below the appliance.
ENGLISH 35 21.3 The inlet hose • Connect the hose to the appliance. Turn the inlet hose only left or right. Loose the ring nut to set it in the correct position. 20 O 45 O • Connect the water inlet hose to the cold water tap with 3/4 thread. CAUTION! Make sure that there are no leaks from the couplings. Do not use an extension hose if the inlet hose is too short. Contact the service centre for the replacement of the inlet hose. Water-stop device The inlet hose has a water stop device.
www.aeg.com With the plastic hose guide. • On the edge of a sink. • Make sure that the plastic guide cannot move when the appliance drains. Attach the guide to the water tap or the wall. • To a stand pipe with vent-hole. Refer to the illustration. Directly into a drain pipe at a height of not less than 60 cm and not more than 100 cm. The end of the drain hose must always be ventilated , i.e. the inner diameter of the drainpipe must be larger than the external diameter of the drain hose.
ENGLISH You can extend the drain hose to maximum 400 cm. Contact the service centre for the other drain hose and the extension. 22. ENVIRONMENT CONCERNS Recycle the materials with the symbol . Put the packaging in applicable containers to recycle it. Help protect the environment and human health and to recycle waste of electrical and electronic appliances. Do not dispose appliances marked with the symbol with the household waste.
www.aeg.
ENGLISH 39
132924150-A-242012 www.aeg.