LAVAMAT 5420 Washing machine User information
Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control Panel . . . . . . . . . . . . . . . . . .
Installation and connection instructions. . . . . . . . . . . . . . . . . 24 Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the transit packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where to install . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. • If the appliance is delivered in the winter months when there are minus temperatures: Store the washing machine at room temperature for 24 hours before using for the first time. Correct use • The washing machine is only designed for the washing of normal domestic laundry at home. • Additions or modifications to the washing machine are not permitted.
case of a permanent connection – switch off the cut-out in the fuse box or remove the screw fuse completely. • If operation is stopped, disconnect the appliance from the mains supply and shut off the water tap. • Never unplug the appliance by pulling on the cable. Always pull the plug. • Multi-way plugs, connectors and extension cables must not be used. This could constitute a fire hazard through overheating. • Never wash the washing machine down with a water jet.
Description of the appliance Detergent dispenser drawer Control panel Rating plate (behind door) Plinth flap/ Drain pump Screw feet (height adjustable) Control Panel SPIN/RINSE HOLD button Programme option buttons Programme Progress display DOOR indicator Programme knob START/PAUSE button 7
Programme overview 1000 600 n (RINSE HOLD) • • • • • • • • • • • • • • • • • } (STAIN) • v (PRE WASH) • max. load 1) (dry washing) • ECO (ENERGY SAVING) 2) 5kg • • c (COTTONS/LINEN) 95, 60, 40, 30 5kg • •3) •4) m (EASY-CARES) 60, 40, 30 2,5kg • •3) d (DELICATES) 40, 30 2,5kg • Programme s (WOOL) H (Hand wash) 30, X (COLD) j (GENTLE RINSE) Spin speed 1400 Q (QUICK WASH) Programme options 2kg 2.
Use/Characteristics Energy-saving programme at 60 °C for lightly to normally soiled whites/ coloureds made of cotton/linen. Programme for normally to heavily soiled whites and coloureds made of cotton/ linen. Programme for easy-care mixed fibres and synthetics. Gentle programme for delicate fabrics such as bonded fabrics, microfibres, synthetics, net curtains (max. load for net curtains 15 to 20 m2). With n (RINSE HOLD) also suitable for materials that have climatic membranes, e.g. outdoor clothing.
Before the first wash 1. Open the detergent drawer. 2. Pour approx. 1 litre of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly. 3. In order to remove any residues from the drum and water container which may have been left during manufacturing, perform the first wash cycle without any washing in the machine. Programme: c (COTTONS/LINEN) 60, press Q (QUICK WASH), add approx.
Running a washing cycle Opening the door/Loading the washing 1. To open the door: pull the door’s handle. When the appliance is switched on, the K (DOOR) and S/P (START/ PAUSE) indicators show whether the door can be opened: K (DOOR) indicator S/P (START/PAUSE) indicator Can the door be opened? flashing flashing yes, after approx. 2 minutes illuminated illuminated no, water level and/or temperature too high off flashing yes 2. Separate individual items and load washing loosely into the machine.
• From water hardness 2 (= medium) upwards, water softener should be used. Detergent can then always be dosed for water hardness 1 (= soft). Your local water company will be able to give you information about the water hardness in your area. 1. Pull the detergent dispenser drawer out as far as the stop. 2. Add the detergent/additives. 3. Push the drawer in fully.
Changing the spin speed/Selecting rinse hold 3 The washing machine suggests the maximum permitted spin speed that is suitable for the selected programme. You can reduce this spin speed: To do this press the Spin/n (RINSE HOLD) button repeatedly until the desired indicator lights up. The speed for the final spin can still be altered during the programme. To do this: 1. Press the S/P (START/PAUSE) button. 2. Change the spin speed. 3. Press the S/P (START/PAUSE) button again.
Switching RINSE+ on and off When r+ (RINSE+) is switched on, there are two additional rinses in the c (COTTONS/LINEN), m (EASY-CARES), d (DELICATES) and j (GENTLE RINSE) programmes. r+ (RINSE+) remains permanently saved – even after the appliance is switched off. To switch on r+ (RINSE+): 1. Turn the programme knob to c (COTTONS/LINEN), m (EASY-CARES) or d (DELICATES) (at any temperature). 2.
Interrupting a programme/adding washing Interrupting a programme • A washing programme can be interrupted at any time by pressing the S/P (START/PAUSE) button. It is then re-started by pressing the S/P (START/PAUSE) button again. • To stop the washing machine before the programme has ended, turn the programme knob to O (OFF). Important! Be careful if there is water in the appliance! Adding washing It is possible to add washing, as long as the K (DOOR) light is not lit. 1. Press the S/P (START/PAUSE) button.
Child safety device When the child safety device is set, the door can no longer be closed. Setting the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go. 1 16 Warning! The knob must not be sunk-in after being set, otherwise the child safety device is not active. The knob must stand proud as shown in the illustration. Releasing the child safety device: Turn the knob anti-clockwise as far as it will go.
Cleaning and maintenance Important! Do not use furniture care products or aggressive cleaners to clean the appliance. Wipe control panel and body with a damp cloth. Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2. Remove the conditioner insert from the middle compartment. 3. Clean all parts with water. 4. Put the conditioner insert in as far as it will go, so that it is firmly in place. 5.
What to do if... Remedying minor malfunctions yourself If the programme progress display shows one of the following error messages during operation: – E (END) flashes 1x (problem with water inflow), – E (END) flashes 2x (problem with water outflow), – E (END) flashes 4x (door open), please refer to the following table. After the error has been remedied, press the S/P (START/PAUSE) button.
Problem Possible cause Transit packaging has not been removed. Washing machine vibrates when operating or is noisy. Remedy Remove transit packaging. Adjust feet according to the Screw feet not correctly adInstallation and Connection justed. instructions. There is very little washing in the drum (e.g., just one bath robe). This does not affect how the machine operates. Screw connection on the inTighten inlet hose. let hose is leaking. Drain hose is leaking.
Problem Possible cause Door locked. Door cannot be opened when appliance is Power cut. (All display indiswitched on. cators are off.) Door remains locked for approx. 2 minutes. Washing is heavily creased. Possibly too much washing was loaded. Remedy Wait until K (DOOR) light goes off and E (END) light comes on. Programme continues, when power cut is over. To remove washing: If water can be seen in the appliance, before opening the door, first drain off the water.
Carrying out an emergency drain 1 Warning! Before emergency draining, switch off the washing machine and remove the mains plug from the socket. Warning! The water that comes out of the emergency drain hose may be hot. There is a risk of scalding. Let the water cool before performing an emergency drain. 1. Open the plinth flap and remove it. 2. Take out the emergency drain hose. 3. Place a shallow container underneath it.
Drain pump 1 The drain pump is maintenance-free. It is only necessary to open the pump cover if there is a malfunction and water is no longer being pumped out, e. g. if the pump wheel is blocked. Please make sure before loading the washing that there are no foreign bodies in the pockets or caught between the washing. Paperclips, nails, etc. that may have got into the washing machine with the washing remain in the pump housing (foreign body trap that protects the pump wheel).
Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x Width x Depth 850 x 598 x 603 mm Depth when door is open 980 mm Height adjustment approx. +10/-5mm Load (depending on programme) Max.
Installation and connection instructions 1 Safety information for the installation • This washing machine cannot be built-in. • Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. • Before using for the first time, all parts of the transit packaging must be removed.
Installing the appliance Transporting the appliance 1 Warning! The washing machine is very heavy. Risk of injury. Be careful when lifting. • Do not lay the appliance on its front nor on its right side (as seen from the front). Electrical components may get wet. • Never transport the appliance without its transit packaging. Only remove the transit packaging when the appliance is in its place of installation. Transporting the appliance without its transit packaging can lead to damage to the appliance.
3 Special spanner A and sealing caps B (2 off) and C (1 off) are supplied with the appliance. 3. Remove screw D with its compression spring using special spanner A. 4. Turn sealing cap C upside down as shown in the illustration. 5. Seal hole using sealing cap C. 6. Unscrew and remove two screws E using special spanner A. 7. Unscrew and remove four screws F using special spanner A. 8. Remove transit bar G. 9. Screw in the four screws F again. 10. Seal the two big holes using sealing caps B.
If the appliance is to stand on a plinth: In order for the appliance to be secure on the plinth, fixing plates*) must be mounted, into which the appliance is inserted. If the appliance is to stand on floors that vibrate, e. g. floors of wooden joists with deal boards: If possible, install the appliance in one corner of the room. 1. Screw a water-resistant wooden board (at least 15 mm thick) onto at least 2 of the floor joists. 2.
Electrical connection Details about the voltage, type of supply and the fuses required are to be found on the rating plate. The rating plate is next to the doorway. Connecting to the water supply Important! • This appliance must not be connected to the hot water system. • When connecting it, use only new hose kits. • Only connect the appliance to the drinking water supply. Rain water or water for industrial use may only be used if it fulfils the requirements of DIN1986 and DIN1988.
Water inflow 3 A 1.35 m long pressure hose is supplied with the appliance. If a longer water inlet hose is required, only original hoses are to be used. The Customer Care Department stocks hose kits of different lengths. Sealing rings are either inserted in the plastic nuts of the threaded hose fitting or are included as spare parts . Do not use any other seals. Important! All threaded hose fittings must only be tightened by hand. 1. Connect the hose with the right-angle connector to the machine.
Water drainage The maximum permitted difference between the height of the surface on which the appliance is installed and the water outlet is 1 metre. Only original hoses may be used to extend hoses. (A maximum of 3 m laid on the floor and then 80 cm vertically). The Customer Care Department stocks outlet hoses of different lengths. Draining water into a sink outlet Secure the outlet/sink outlet joint with a hose band clip (available from your dealer).
Guarantee Conditions Belgium DECLARATION OF GUARANTEE TERMS. Our appliances are produced with the greatest of care. However, a defect may still occur. Our consumer services department will repair this upon request, either during or after the guarantee period. The service life of the appliance will not, however, be reduced as a result. This declaration of guarantee terms is based on European Union Directive 99/44/EC and the provisions of the Civil Code.
These guarantee terms are only valid for appliances purchased and used in Belgium. For exported appliances, the user must first make sure that they satisfy the technical conditions (e.g.: voltage, frequency, installation instructions, type of gas, etc.) for the country concerned and that they can withstand the local climatic and environmental conditions. For appliances purchased abroad, the user must first ensure that they meet the qualifications required in Belgium.
Customer Service Centres Belgium Electrolux Home Products Belgium ELECTROLUX SERVICE Bergensesteenweg 719 1502 Lembeek E-mail: consumer.services@electrolux.be Consumer services Tel.: 02/363.04.44 Fax.: 02/363.04.00 02/363.04.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.
