LAVAMAT 66680 Waschautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Entsorgung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Bedienblende . . . . . . . . . . . . . . . . . . . . .
Aufstell- und Anschlussanweisung . . . . . . . . . . . . . . . . . . . . . . . 24 Sicherheitshinweise für die Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Aufstellung des Gerätes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Gerät transportieren . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transportsicherung entfernen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. • Bei Geräteanlieferung in Wintermonaten mit Minustemperaturen: Waschautomat vor Inbetriebnahme für 24 Stunden bei Raumtemperatur lagern. Bestimmungsgemäße Verwendung • Der Waschautomat ist nur zum Waschen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Waschautomaten sind nicht zulässig.
bei Festanschluss – LS-Schalter im Sicherungskasten ausschalten bzw. Schraubsicherung ganz herausdrehen. • Bei Betriebspausen das Gerät vom Stromnetz trennen und Wasserhahn schließen. • Netzstecker nie am Kabel aus der Steckdose ziehen, sondern am Stecker. • Vielfachstecker, Kupplungen und Verlängerungskabel dürfen nicht verwendet werden. Brandgefahr durch Überhitzung! • Den Waschautomaten nicht mit einem Wasserstrahl abspritzen.
Gerätebeschreibung Bedienblende Waschmittelschublade Typschild (hinter Einfülltür) Sockelklappe/ Laugenpumpe Schraubfüße (höhenverstellbar) Bedienblende Taste Schleudern/ SPÜLSTOPP Multidisplay Taste ZEITVORWAHL Programmzusatz-Tasten Taste START/PAUSE Programmablauf-Anzeige Anzeige TÜR Programmwähler Anzeige ÜBERDOSIERT 7
Programmübersicht 3kg LEICHTBÜGELN 40 • • • • • • • • • • •3) • • • • • • • • • •3) • • • • 1kg • • • • • • • FEINWÄSCHE 40, 30 3kg • • • • • • WOLLE/SEIDE H (Handwäsche) 40, 30, KALT 2kg • • • FEINSPÜLEN 3kg • • • • • • • Programm ZEITSPAREN SPÜLSTOPP PFLEGELEICHT 60, 50, 40, 30 600 • 1000 6kg 1200 KOCHWÄSCHE/BUNTWÄSCHE 95, 60, 50, 40, 30 1600 • SENSITIV 6kg FLECKEN EXTRASPÜLEN ENERGIESPAREN 2) Schleuderdrehzahl VORWÄSCHE max.
Anwendung/Eigenschaften Energiesparprogramm bei 60 °C für leicht bis normal verschmutzte Koch-/Buntwäsche aus Baumwolle/Leinen. Programm für normal bis stark verschmutzte Koch-/Buntwäsche aus Baumwolle/ Leinen. Programm für pflegeleichte Mischgewebe und Synthetics. Spezialprogramm bei 40 °C für pflegeleichte Textilien, die im Anschluss an dieses Programm nur noch leicht oder gar nicht gebügelt werden müssen. Schonprogramm für feine Textilien wie Schichtfasern, Mikrofasern, Synthetics, Gardinen (max.
Vor dem ersten Waschen 1. Waschmittelschublade öffnen. 2. Etwa 1 Liter Wasser durch die Waschmittelschublade in den Waschautomaten gießen. Beim nächsten Programmstart wird dadurch der Laugenbehälter geschlossen und die ÖKO-Schleuse kann ordnungsgemäß funktionieren. 3. Um eventuelle fertigungsbedingte Rückstände aus Trommel und Laugenbehälter zu entfernen, den ersten Waschgang ohne Wäsche durchführen. Programm: KOCHWÄSCHE/BUNTWÄSCHE 60, Taste ZEITSPAREN drücken, ca. 1/4 Messbecher Waschpulver zugeben.
Waschgang durchführen Einfülltür öffnen/Wäsche einfüllen 1. Einfülltür öffnen: am Griff der Einfülltür ziehen. Die Anzeigen TÜR und START/PAUSE zeigen bei eingeschaltetem Gerät an, ob die Einfülltür geöffnet werden kann: Anzeige TÜR Anzeige START/PAUSE Tür öffnen möglich? leuchtet grün blinkt rot oder ist aus ja leuchtet grün leuchtet rot ja, nach Drücken der Taste START/PAUSE leuchtet rot oder ist aus blinkt rot oder leuchtet rot nein, zu hoher Wasserstand bzw. zu hohe Temperatur 2.
1. Waschmittelschublade bis zum Anschlag herausziehen 2. Wasch-/Pflegemittel einfüllen. 3. Waschmittelschublade ganz hineinschieben. Waschpulver/Tabs für die Hauptwäsche Weichspüler/ Formspüler/ Stärke Fleckensalz/-tabs Waschpulver/Tabs für die Vorwäsche oder Wasserenthärter Waschpulver/Tabs für die Hauptwäsche Wenn Sie Wasserenthärter benutzen und das rechte Fach für Vorwaschmittel benötigen, den Wasserenthärter auf das Hauptwaschmittel in das linke Fach geben.
Schleuderdrehzahl ändern/Spülstopp wählen 3 Der Waschautomat schlägt die maximal zulässige Drehzahl vor, die für das gewählte Programm geeignet ist. Diese Drehzahl können Sie verringern: Dazu Taste Schleudern/SPÜLSTOPP so oft drücken, bis die gewünschte Anzeige leuchtet. Die Drehzahl für das Endschleudern kann während des Programms noch geändert werden. Dazu: 1. Taste START/PAUSE drücken. 2. Drehzahl ändern. 3. Taste START/PAUSE erneut drücken.
VORWÄSCHE Warmes Vorwaschen vor dem automatisch folgenden Hauptwaschgang; mit Zwischenschleudern bei KOCH/BUNTWÄSCHE und PFLEGELEICHT, ohne Zwischenschleudern bei FEINWÄSCHE. FLECKEN Für stark verschmutzte oder verfleckte Wäsche. Fleckenmittel wird zeitoptimiert während des Programmablaufs eingespült. Nur für Waschtemperaturen ab 40°C einstellbar, da Fleckenmittel erst bei höheren Temperaturen wirksam werden.
Ablauf des Programms 3 • Die Programmablauf-Anzeige zeigt den Programmschritt an, der gerade ausgeführt wird. • Das Multidisplay zeigt die voraussichtliche Restlaufzeit (in Minuten) bis zum Programmende an. Die Restlaufzeit kann sich während des Waschvorgangs verlängern oder kurz stehen bleiben, da sich das Programm an unterschiedliche Bedingungen beim Waschen anpasst (z. B. Wäscheart und -menge, Unwuchterkennung beim Schleudern, Sonderspülgang etc.).
Wenn SPÜLSTOPP gewählt war: Nach Spülstopp leuchtet ENDE auf der Programmablauf-Anzeige. Zuerst muss das Wasser abgepumpt werden: – Entweder Programmwähler auf AUS, anschließend auf PUMPEN drehen und Taste START/PAUSE drücken (es wird ohne Schleudern abgepumpt), – oder Programmwähler auf AUS und anschließend auf SCHLEUDERN drehen. Gegebenenfalls Drehzahl ändern und Taste START/PAUSE drücken (es wird abgepumpt und geschleudert).
Reinigen und Pflegen Achtung! Keine Möbelpflegemittel oder aggressive Reinigungsmittel zur Reinigung des Gerätes benutzen. Bedienblende und Gehäuse mit einem feuchten Tuch abwischen. Waschmittelschublade Die Waschmittelschublade sollte regelmäßig gereinigt werden. 1. Waschmittelschublade mit kräftigem Ruck entnehmen. 2. Weichspülereinsatz aus dem mittleren Fach herausnehmen. 3. Alle Teile mit Wasser reinigen. 4. Weichspülereinsatz bis zum Anschlag aufstecken, so dass er fest sitzt. 5.
Was tun, wenn... Kleine Störungen selbst beheben Falls während des Betriebs einer der folgenden Fehlercodes im Multidisplay angezeigt wird: – E10 (Probleme mit Wasserzulauf), – E20 (Probleme mit Wasserablauf), – E40 (Einfülltür offen), sehen Sie bitte in nachfolgender Tabelle nach. Nachdem der Fehler behoben ist, Taste START/PAUSE drücken. Bei anderen Fehlern (E und Zahl oder Buchstabe): Gerät aus- und wieder einschalten. Programm neu einstellen. Taste START/PAUSE drücken.
Problem Waschautomat vibriert während des Betriebs oder steht unruhig. Mögliche Ursache Abhilfe Transportsicherung nicht entfernt. Transportsicherung entfernen. Schraubfüße nicht korrekt eingestellt. Füße laut Aufstell- und Anschlussanweisung justieren. Nur sehr wenig Wäsche in der Trommel (z.B. nur ein Bademantel). Funktion ist dadurch nicht beeinträchtigt. Verschraubung am Zulaufschlauch undicht. Zulaufschlauch festschrauben. Ablaufschlauch undicht. Ablaufschlauch erneuern.
Problem Mögliche Ursache Einfülltür verriegelt. Einfülltür lässt sich bei eingeschaltetem Gerät nicht öffnen. Wäsche stark verknittert. Abhilfe Warten, bis Anzeige TÜR grün leuchtet. Programm läuft weiter, wenn Stromausfall vorüber ist. Stromausfall! (Alle Anzeigen sind aus.) Einfülltür bleibt ca. 4 bis 10 Minuten verriegelt. Zum Wäsche entnehmen: Ist Wasser im Gerät zu sehen, vor Öffnen der Einfülltür erst das Wasser ablassen (siehe Abschnitt „Notentleerung durchführen“).
Notentleerung durchführen 1 Warnung! Waschautomat vor Notentleerung ausschalten und den Netzstecker aus der Steckdose ziehen! Warnung! Die Waschlauge, die aus dem Notentleerungsschlauch ausläuft, kann heiß sein. Verbrühungsgefahr! Vor einer Notentleerung Waschlauge abkühlen lassen! 1. Sockelklappe aufklappen und abziehen. 2. Notentleerungsschlauch herausnehmen. 3. Flaches Auffanggefäß unterstellen. Anschließend Verschlussstopfen durch Drehen gegen den Uhrzeigersinn lösen und herausziehen. 4.
Laugenpumpe 1 Die Laugenpumpe ist wartungsfrei. Das Öffnen des Pumpendeckels ist nur im Störungsfall erforderlich, wenn kein Wasser mehr abgepumpt wird, z. B. bei blockiertem Pumpenrad. Bitte vor dem Einfüllen der Wäsche immer sicherstellen, dass sich keine Fremdkörper in den Taschen oder zwischen der Wäsche befinden. Büroklammern, Nägel etc., die eventuell mit der Wäsche in den Waschautomaten gelangt sind, bleiben im Pumpengehäuse (Fremdkörperfalle, die das Pumpenrad schützt) liegen.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 850 x 598 x 598mm Tiefe bei geöffneter Einfülltür 1018 mm Höhenverstellbarkeit ca. +10/-6mm Füllmenge (programmabhängig) max.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann es beim Schleudern zu Schäden am Gerät oder an benachbarten Möbeln kommen.
• Gerät niemals ohne Transportsicherung transportieren. Transportsicherung erst am Aufstellort entfernen! Transport ohne Transportsicherung kann zu Schäden am Gerät führen. • Das Gerät nicht an der geöffneten Einfülltür und auch nicht am Sockel anheben. Bei Transport mit der Sackkarre: • Sackkarre nur seitlich ansetzen.
4. Verschlusskappe C gemäß Abbildung umstülpen. 5. Loch mit Verschlusskappe C verschließen. 6. Zwei Schrauben E mit Spezialschlüssel A herausschrauben. 7. Vier Schrauben F mit Spezialschlüssel A herausschrauben. 8. Transportschiene G abnehmen. 9. Die vier Schrauben F wieder einschrauben. 10. Die zwei großen Löcher mit Verschlusskappen B verschließen. Achtung! Alle Verschlusskappen B (2 Stück) und C (1 Stück) so kräftig eindrücken, dass sie in die Rückwand einrasten (Spritzwasserschutz!).
Wenn das Gerät auf schwingenden Böden stehen soll, z. B. Holzbalkenböden mit Dielenbrettern: Gerät möglichst in einer Ecke des Raumes aufstellen. 1. Eine wasserbeständige Holzplatte (mindestens 15 mm dick) auf mindestens 2 Fußbodenbalken festschrauben. 2. Standbleche*) auf die Holzplatte montieren, in die das Gerät eingestellt wird. *) Die Standbleche sind beim Kundendienst erhältlich. Gerät ausrichten Die vier Füße des Gerätes sind voreingestellt.
Zulässiger Wasserdruck Der Wasserdruck muss mindestens 1bar (=10N/cm2 =0,1MPa) und darf höchstens 10bar (=100N/cm2 =1MPa) betragen. – Bei mehr als 10bar: Druckminderventil vorschalten. – Bei weniger als 1bar: Zulaufschlauch geräteseitig am Magneteinlassventil abschrauben und Durchlaufmengenregler herausnehmen (dazu Sieb mit Spitzzange entfernen und dahinterliegende Gummischeibe herausnehmen). Sieb wieder einsetzen. Wasserzulauf 3 Mitgeliefert wird ein Druckschlauch von 1,5m Länge.
2. Schlauch mit dem geraden Anschluss an einen Wasserhahn mit Schraubgewinde R 3/4 (Zoll) anschließen. 3. Wasserhahn langsam öffnen und prüfen, ob alle Anschlüsse dicht sind. Wasserablauf Der Höhenunterschied zwischen Standfläche und Wasserabfluss darf höchstens 1 Meter betragen. Zur Verlängerung dürfen nur Originalschläuche verwendet werden. (Max. 3 m auf dem Fußboden verlegt und dann bis 80 cm hoch). Der Kundendienst führt Ablaufschläuche in verschiedenen Längen.
1 Wasserablauf in ein Waschbecken/Badewanne Achtung! – Kleine Becken sind nicht geeignet. Wasser kann überlaufen! – Das Ende des Ablaufschlauches darf nicht ins abgepumpte Wasser eintauchen. Wasser könnte sonst ins Gerät zurückgesaugt werden! – Bei Ablauf in ein Waschbecken bzw. eine Badewanne den Ablaufschlauch mit dem mitgelieferten Krümmer gegen Abrutschen sichern. Das auslaufende Wasser kann sonst den Schlauch aus dem Becken drücken. – Beim Abpumpen prüfen, ob das Wasser schnell genug abläuft.
Küchen mit Arbeitshöhe 85 cm 1 Der Waschautomat kann nach Abnahme der Geräte-Arbeitsplatte unter vollständig geschlossene und durchgehende Küchen-Arbeitsplatten mit Arbeitshöhe 85 cm untergebaut werden. Die Gerätehöhe reduziert sich dadurch auf ca. 82cm. Zum Unterbau des Waschautomaten ist ein Unterbausatz erforderlich. Der Unterbausatz ist bei Ihrem Fachhändler erhältlich.
Garantiebedingungen/Kundendienststellen Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
nicht ermächtigt sind, verursacht wurden. Werden unsere Geräte mit Ersatzteilen oder Zubehörteilen versehen, die keine Originalteile sind und wurde dadurch ein Defekt verursacht, ist dieser ebenfalls nicht durch die Garantie gedeckt. 3. Mängel dieses Gerätes werden wir innerhalb angemessener Frist nach Mitteilung des Mangels unentgeltlich beseitigen. Die zu diesem Zweck erforderlichen Aufwendungen, insbesondere Transport-, Weg-, Arbeits- und Materialkosten werden von uns getragen.
Internet: office@a-hell.at Kundendienststelle Salzburg Hausgeräte Kundendienst Wörndl Elektro Ges.m.b.H & CO KEG 5020 Salzburg, Gnigler Straße 18 Tel. Fax Internet: woerndl-kundendienst@aon.at Kundendienststelle Kärnten, Osttirol Elektroservice H. Schneider 9020 Klagenfurt, Rosentalerstraße 189 Tel. Fax Internet: elektroservice.schneider@aon.at Kundendienststelle Tirol BEP! Hausgeräte-Kundendienst GesmbH 6020 Innsbruck, Amraser Straße 118 Tel. Fax Internet: bep.innsbruck@aon.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Einsatz Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg.hausgeraete.