LAVAMAT 74800 Washing machine User information
Dear customer, Please read this User Information carefully and keep it to refer to at a later date. Pass this User Information on to any subsequent owner of the appliance. 1 3 2 2 The following symbols are used in the text: Safety instructions Warning: Notes that concern your personal safety. Attention: Notes that show how to avoid damage to the appliance.
Contents Operating Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Description of the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Programme overview . . . . . . . . . . . . . . . . . .
Installation and connection instructions. . . . . . . . . . . . . . . . . 29 Safety information for the installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 29 Installing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Transporting the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Removing the transit packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Where to install . .
Operating Instructions 1 Safety Prior to using for the first time • Follow the ”Instructions for installation and connection”. • If the appliance is delivered in the winter months when there are minus temperatures: Store the washing machine at room temperature for 24 hours before using for the first time. Correct use • The washing machine is only designed for the washing of normal domestic laundry at home. • Additions or modifications to the washing machine are not permitted.
General safety • Repairs to the washing machine must only be carried out by qualified service engineers. • Never use the washing machine if the mains cable is damaged; or if the control panel, work top or plinth area is damaged such that the inside of the appliance is freely accessible. • Switch off the washing machine before cleaning, maintenance and servicing.
Description of the appliance Detergent dispenser drawer Control panel Rating plate (behind door) Plinth flap/ Drain pump Screw feet (height adjustable) Control panel Spin/RINSE HOLD button Multi-display DELAY TIMER button Additional programme buttons START/PAUSE button Programme progress display DOOR indicator Programme selector OVERDOSING indicator 7
Programme overview (PRE-WASH) (STAIN) (SENSITIVE) 1400 1000 700 500 n (RINSE HOLD) (QUICK WASH) • • • • • • • • •4) • • • • • • • • • • • • • • • • •4) • • • • • • • • • • • • • • • • • • • • 2kg • • • • 3kg • • • • • • • • • • ECO (ENERGY SAVING) 2) 6kg • (COTTONS/LINEN) 95, 60, 40, 30 6kg • 40-60 MIX 6kg • (EASY-CARES) 60, 50, 40, 30 3kg • l (EASY IRON) 40 1kg (DELICATES) 40, 30 3kg / / (WOOL/SILK/HANDWASH) 40, 30, (CO
Care symbols1) Application/features Energy saving programme at 60 °C for lightly to normally soiled cottons/linen. MO Programme for normally to heavily soiled cottons/linen. JMO Programme for cottons/linen for which are labelled for different wash temperatures. Items which according to their care symbols are normally to be washed separately at 40 °C or at 60 °C, can be washed together in this programme. Achieves the washing results of a normal 60° programme.
Before the first wash 1. Open the detergent drawer. 2. Pour approx. 1 litre of water through the detergent drawer into the washing machine. This closes the water container when the next programme is started and the economy valve can function properly. 3. In order to remove any residues from the drum and water container which may have been left during manufacturing, perform the first wash cycle without any washing in the machine. Programme: (COTTONS/LINEN) 60, press (QUICK WASH), add approx.
Running a washing cycle Opening the door/Loading the washing 1. To open the door: gently pull the handle on the door. When the machine is switched on, the lights (DOOR) and (START/PAUSE) indicate whether the door can be opened: light (DOOR) light (START/PAUSE) lit green flashes red or is off lit green lit red lit red or is off flashes red or lit red Can the door be opened? yes yes, after pressing the (START/PAUSE) button no, water level too high or temperature too high 2.
1. Pull the detergent dispenser drawer out as far as the stop. 2. Add the detergent/additives. 3. Push the drawer in fully.
Changing the spin speed/Selecting rinse hold The washing machine suggests the maximum permitted speed that is suitable for the selected programme. You can reduce this speed: 3 Press the spin/ (RINSE HOLD) button a number of times until the desired indicator lights up. The speed for the final spin can still be altered during the programme. To do this: 1. Press the (START/PAUSE) button. 2. Change the spin speed. 3. Press the (START/PAUSE) button again.
Selecting the programme options 3 If desired, press the programme option button(s). The corresponding indicator lights up. If ”Err” flashes in the multi-display, the programme option selected cannot be combined with the wash programme set. EXTRA RINSE Two additional rinse cycles will be carried out (e.g. in the case of sensitive skin) for the programmes ECO (ENERGY SAVING), (COTTONS/ LINEN), (DELICATES), (EASY-CARES) and l (EASY IRON). QUICK WASH Shortened wash programme for less soiled items.
Setting the delay timer 3 3 Using the button (DELAY TIMER) you can delay the start of a programme by 30 minutes (30') to a maximum of 23 hours (23h). 1. Select the programme. 2. Press the button (DELAY TIMER) repeatedly until the multi-display shows the desired time delay, e. g., 12h, if the programme is to start in 12 hours. The indicator (DELAY TIMER) will light up. If the display is showing 23h and you press the button again, the time delay will be cancelled.
Programme progress 3 • The programme progress display shows the programme step that is currently being carried out. – (Prewash) – (Main wash) – (Rinse) – (Extra Rinse) – (Spin) – (End) • The multi-display shows the estimated time remaining (in hours and minutes) until the end of the programme. The remaining programme time may increase or briefly remain constant during the wash programme as the programme adjusts to various conditions while washing (e. g.
End of the wash cycle/Removing the washing When the programme has finished, (END) will illuminate on the programme progress display. The door can be opened as soon as the indicator (DOOR) is lit green. 1. Open the door and remove the washing. 2. Turn the programme knob to (OFF). 3. Close the water tap. 4. When you have finished washing, pull out the detergent drawer a little to let it to dry out. Keep the door very slightly open so that the washing machine can air.
Child safety device When the child safety device is set, the door can no longer be closed. Setting the child safety device: Use a coin to turn the knob (on the inside of the door) in a clockwise direction as far as it will go. 1 18 Warning! The knob must not be sunk-in after being set, otherwise the child safety device is not active. The knob must stand proud as shown in the illustration. Releasing the child safety device: Turn the knob anti-clockwise as far as it will go.
Cleaning and maintenance Important! Do not use furniture care products or aggressive cleaners to clean the appliance. Wipe control panel and body with a damp cloth. Cleaning procedure If you plan to wash mainly at low temperature, you should run a hot programme from time to time. This will reduce any deposits and clean the appliance from the inside. Detergent dispenser drawer The detergent dispenser drawer should be cleaned regularly. 1. Remove the detergent dispenser drawer by pulling it firmly. 2.
Door and rubber collar Regularly check whether deposits or foreign bodies are present in the folds of the rubber collar or on the inside of the glass door. Clean the glass in the door and the rubber collar regularly. What to do if... Remedying small malfunctions If during use of the appliance one of the following error codes is shown in the multi-display: – E10 (Problems with water inflow), – E20 (Problems with water outflow), – E40 (door open), please have a look at the following table.
Problem E10 appears. The (END) indicator flashes 1x, and an acoustic signal sounds 1x. (Problems with water inflow.) Possible cause Tap turned off. Remedy Turn on the tap. Turn off the tap. Unscrew the The filter in the threaded inhose, take out the filter and let hose fitting is blocked. clean it. Water tap is furred with lime scale or is faulty. Check the tap and have it repaired, if necessary. The transit bar has not been Remove the transit bar. removed.
Problem Fabric softener was not rinsed in, the compartment w for conditioners is full of water. Possible cause Fabric softener insert in the Clean the detergent drawer, compartment for conditioninsert the fabric softener ers is not correctly attached insert firmly. or is blocked. Door locked. The door cannot be opened when the wash- There has been a power cut. ing machine is switched (All the indicator are off). on. The door remains blocked for approx. 4 to 10 minutes. Washing is heavily creased.
If the wash results are not satisfactory Washing is grey and scale is being deposited in the drum • Too little detergent is being used. • The right detergent was not used. • Special soiling was not pre-treated. • Programme or temperature was not correctly set. There are grey stains on the washing. • Washing soiled with ointment, grease or oil was washed with too little detergent. • It was washed at too low a temperature.
Carrying out an emergency drain 1 Warning! Before emergency draining, switch off the washing machine and remove the mains plug from the socket. Warning! The water that comes out of the emergency drain hose may be hot. There is a risk of scalding. Let the water cool before performing an emergency drain. 1. Open the plinth flap and remove it. 2. Take out the emergency drain hose. 3. Place a shallow container underneath it.
Drain pump 1 The drain pump is maintenance-free. It is only necessary to open the pump cover if there is a malfunction and water is no longer being pumped out, e. g. if the pump wheel is blocked. Please make sure before loading the washing that there are no foreign bodies in the pockets or caught between the washing. Paperclips, nails, etc. that may have got into the washing machine with the washing remain in the pump housing (foreign body trap that protects the pump wheel).
Disposal 2 2 Packaging material The packaging materials are environmentally friendly and can be recycled. The plastic components are identified by markings, e.g. >PE<, >PS<, etc. Please dispose of the packaging materials in the appropriate container at the community waste disposal facilities. Old appliance W 1 26 The symbol on the product or on its packaging indicates that this product may not be treated as household waste.
Technical data 5 This appliance conforms with the following EU Directives: – 73/23/EEC dated 19.02.1973 Low Voltage Directive – 89/336/EEC dated 03.05.1989 EMC Directive inclusive of Amending Directive 92/31/EEC – 93/68/EEC dated 22.07.1993 CE Marking Directive Height x Width x Depth 850 x 598 x 640 mm Depth when door is open 1017 mm Height adjustment approx. +10/-5mm Load (depending on programme) Max.
Consumption values The consumption values were obtained under standardised conditions. They may vary when operating in domestic conditions. Programme selector Temperature Load size in kg1) Water in litres Energy in kWh (COTTONS/LINEN) 95 6 62 2,20 2) 6 45 1,02 (COTTONS/LINEN) 40 6 58 0,70 (EASY-CARES) 40 3 58 0,52 (DELICATES) 30 3 58 0,42 2 54 0,35 ECO (ENERGY SAVING) / / (WOOL/SILK/HANDWASH) 30 1) The load size is determined in accordance with the EN 60456 standard load.
Installation and connection instructions 1 Safety information for the installation • This washing machine cannot be built-in. • Before using for the first time, check the appliance for damage sustained while it was being transported. Do not under any circumstances connect an appliance that is damaged. In the case of damage, please contact your supplier. • Before using for the first time, all parts of the transit packaging must be removed.
Installing the appliance Transporting the appliance 1 Warning! The washing machine is very heavy. Risk of injury. Be careful when lifting. • Do not lay the appliance on its front nor on its right side (as seen from the front). Electrical components may get wet. • Never transport the appliance without its transit packaging. Only remove the transit packaging when the appliance is in its place of installation. Transporting the appliance without its transit packaging can lead to damage to the appliance.
3. Remove both plastic caps sideways. 3 Special spanner A and sealing caps B (2 off) and C (1 off) are supplied with the appliance. 4. Remove screw D with its compression spring using special spanner A. 5. Turn sealing cap C upside down as shown in the illustration. 6. Seal hole using sealing cap C. 7. Unscrew and remove two screws E using special spanner A. 8. Unscrew and remove four screws F using special spanner A. 9. Remove transit bar G. 10. Screw in the four screws F again. 11.
• The surface on which the appliance is to be installed must be clean and dry and free from coverings that move, so that the appliance does not slide. • If the location in which the appliance is to be installed is fitted with small-format tiles, put a rubber mat (available in the shops) under the appliance. If the appliance is to stand on a plinth: In order for the appliance to be secure on the plinth, fixing plates*) must be mounted, into which the appliance is inserted.
Electrical connection Details about the voltage, type of supply and the fuses required are to be found on the rating plate. The rating plate is next to the doorway. Connecting to the water supply Important! • This appliance must not be connected to the hot water system. • When connecting it, use only new hose kits. • Only connect the appliance to the drinking water supply. Rain water or water for industrial use may only be used if it fulfils the requirements of DIN1986 and DIN1988.
Water inflow 3 A 1.35 m long pressure hose is supplied with the appliance. If a longer water inlet hose is required, only original hoses are to be used. The Customer Care Department stocks hose kits of different lengths. Sealing rings are either inserted in the plastic nuts of the threaded hose fitting or are included as spare parts . Do not use any other seals. Important! All threaded hose fittings must only be tightened by hand. 1. Connect the hose with the right-angle connector to the machine.
Water drainage The maximum permitted difference between the height of the surface on which the appliance is installed and the water outlet is 1 metre. Only original hoses may be used to extend hoses. (A maximum of 3 m laid on the floor and then 80 cm vertically). The Customer Care Department stocks outlet hoses of different lengths. Draining water into a sink outlet Secure the outlet/sink outlet joint with a hose band clip (available from your dealer).
Guarantee/Customer Service Weitere Kundendienststellen im Ausland In diesen Ländern gelten die Garantiebedingungen der örtlichen Partner. Diese können dort eingesehen werden. Further after-sales service agencies overseas In these countries our AEG-Electrolux agents’ own guarantee conditions are applicable. Please obtain further details direct. Autres agences étrangères assurant le service après-vente Dans ces pays, les conditions de garantie des concessionnaires de la région sont valables.
U.A.E. Abu Dhabi Universal Trading Company P.O. Box 43 99 Tel.: 6335331 Service Center 6733974 Jordan Jordan Household Supply Co. Ltd. P.O. Box 3/68 Amman/Tel.: 69 70 50 Malta ITC International Trading Company White House Building Mountbatte Street Blata L-Bajda/Tel.: 220644 Egypt Middle East Commercial Center 4 Salah El Dein St. - 2nd floor Heliopolis, Kairo Egypt Tel.: 2024181719 Canada EURO-LINE Appliances 2150 Winston PARK Drive 20 Oakville, Ontario L6H 5V1 Tel.
Israel Evis Ltd. Tadiran-Ampa Service 10 Gibonay Israel Street New Industrial Zone Netanya, 42504 Israel Malaysia Arzbergh Engineering No. 49A/B, Jalan Petaling Utama 7 4600 Petaling Jaya Tel.: 3 795 1084 Fax: 3 795 1082 Saudi Arabia Awad Badi Nahas Est Shara Siteen Jeddah 21463 Phone: 6646583 Alia Trading Co Mecca Road Riyadh 11491 Phone 4645977 Japan Electrolux Japan Ltd. Domestic Appliances Department Maruzen Showa Warehouse Building Tookai 4-5-12, Ota-ku 143-006 Tokyo Tel.
Service In the event of technical faults, please first check whether you can remedy the problem yourself with the help of the operating instructions (section “What to do if…”). If you were not able to remedy the problem yourself, please contact the Customer Care Department or one of our service partners. In order to be able to assist you quickly, we require the following information: – Model description – Product number (PNC) – Serial number (S No.
From the Electrolux Group. The world´s No.1 choice. The Electrolux Group is the world´s largest producer of powered appliances for kitchen, cleaning and outdoor use. More than 55 million Electrolux Group products (such as refrigerators, cookers, washing machines, vacuum cleaners, chain saws and lawn mowers) are sold each year to a value of approx. USD 14 billion in more than 150 countries around the world. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.