LAVAMAT 86820 Waschautomat Benutzerinformation
Sehr geehrte Kundin, sehr geehrter Kunde, lesen Sie bitte diese Benutzerinformation sorgfältig durch und bewahren Sie sie zum späteren Nachschlagen auf. Geben Sie diese Benutzerinformation an eventuelle Nachbesitzer des Gerätes weiter. 1 3 2 2 Folgende Symbole werden im Text verwendet: Sicherheitshinweise Warnung! Hinweise, die Ihrer persönlichen Sicherheit dienen. Achtung! Hinweise, die zur Vermeidung von Schäden am Gerät dienen.
Inhalt Gebrauchsanweisung. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Sicherheit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Gerätebeschreibung . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Bedienblende . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Anzeigen im Display . . . . . . . . . . . . . . . . . . . . . . .
Reinigen und Pflegen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Was tun, wenn.... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Kleine Störungen selbst beheben. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Wenn das Waschergebnis nicht befriedigend ist . . . . . . . . . . . . . . . . . . . . . . Notentleerung durchführen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Gebrauchsanweisung 1 Sicherheit Vor der ersten Inbetriebnahme • Beachten Sie die „Aufstell- und Anschlussanweisung“. • Bei Geräteanlieferung in Wintermonaten mit Minustemperaturen: Waschautomat vor Inbetriebnahme für 24 Stunden bei Raumtemperatur lagern. Bestimmungsgemäße Verwendung • Der Waschautomat ist nur zum Waschen haushaltsüblicher Wäsche im Haushalt bestimmt. • Umbauten oder Veränderungen am Waschautomaten sind nicht zulässig.
Allgemeine Sicherheit • Reparaturen am Waschautomaten dürfen nur von Fachkräften durchgeführt werden. • Den Waschautomaten niemals in Betrieb nehmen, wenn das Netzkabel beschädigt ist oder Bedienblende, Arbeitsplatte oder Sockelbereich so beschädigt sind, dass das Geräteinnere offen zugänglich ist. • Vor Reinigung, Pflege und Wartungsarbeiten den Waschautomaten ausschalten. Zusätzlich Netzstecker aus der Steckdose ziehen oder – bei Festanschluss – LS-Schalter im Sicherungskasten ausschalten bzw.
Gerätebeschreibung Bedienblende Waschmittelschublade Typschild (hinter Einfülltür) Drei Schraubfüße (höhenverstellbar); hinten links: Automatikfuß Sockelklappe/ Laugenpumpe Bedienblende Programmwähler und Ein-/Aus-Schalter Display Funktions-Tasten Taste START/PAUSE Anzeigen im Display Informationsfeld, zeigt aktuelle Einstellungen an KOCHWÄSCHE Programmende um Temperatur 12.45 Aktuelle Uhrzeit 15.
Programmübersicht KOCHWÄSCHE 7kg2) • • • • BUNTWÄSCHE/ PFLEGELEICHT 60°, 50°, 40°, 30°, Kalt 7kg2) bzw. 3,5kg • • •4) • 40 - 60 MIX 7kg2) • • • • FEINWÄSCHE 40°, 30°, Kalt 3,5kg • •4) • SPÜLSTOPP • 0 • 1200/1000/ 800/600/400 • 1600/1400 NACHTPROGRAMM • Schleuderdrehzahl STARTZEITVORWAHL FLECKEN 7kg2) EXTRA KURZ SENSITIV ENERGIESPAREN 1) Programm • • • • • •3) •3) • • • • • •3) •3) • • • • • • • • • • • • • • KURZ VORWÄSCHE Zeiten max.
Anwendung/Eigenschaften Pflegesymbole1) Energiesparprogramm bei 60 °C für leicht bis normal verschmutzte Koch-/Buntwäsche aus Baumwolle/Leinen. MO Programm bei 95 °C für normal bis stark verschmutzte Kochwäsche aus Baumwolle/ Leinen. O Universalprogramm für Koch-/Buntwäsche aus Baumwolle/Leinen sowie für pflegeleichte Mischgewebe und Synthetics. Das Programm passt sich automatisch an die unterschiedlichen Gewebearten und Füllmengen an. Bei reiner Beladung mit pflegeleichter Wäsche nur 3,5kg einfüllen.
Begriffsübersicht Die in dieser Benutzerinformation verwendeten deutschen Begriffe entsprechen nachstehenden niederländisch/französischen Bezeichnungen auf der Bedienblende Ihres Gerätes: Programmwähler 10 Tasten AUS UIT/ARRET TEMPERATUR TEMP.C° KOCHWÄSCHE KOOK WAS BLANC U/MIN. T/MIN.
Vor der ersten Inbetriebnahme Das erste Einschalten - Sprache einstellen 3 Ab Werk ist die Displayanzeige standardmäßig Niederländisch eingestellt. Wichtig! Falls das Display nach dem Einschalten des Gerätes nicht das Menü für die Spracheinstellung anzeigt, wurde das Gerät vorher schon einmal eingeschaltet. Sehen Sie in diesem Fall bitte im Kapitel „Extras/ Sprache“ nach. Zum Einschalten des Gerätes Programmwähler auf ein beliebiges Programm drehen, z. B. KOCHWÄSCHE.
Uhrzeit einstellen Damit Uhrzeit und Programmende korrekt angezeigt werden, bitte die Anzeige im Display überprüfen und gegebenenfalls die aktuelle Uhrzeit einstellen. Sehen Sie dazu bitte im Kapitel „Extras/Uhr“ nach. Vorreinigung durchführen Um eventuelle fertigungsbedingte Rückstände aus Trommel und Laugenbehälter zu entfernen, den ersten Waschgang ohne Wäsche durchführen. Programm: BUNTWÄSCHE/PFLEGELEICHT 60 °C, Option ZEIT SPAREN: EXTRA KURZ, ca. 1/4 Messbecher Waschpulver dosieren.
Waschgang durchführen Wasch-/Pflegemittel einfüllen Achtung! Nur Wasch-/Pflegemittel verwenden, die für HaushaltsWaschautomaten geeignet sind. Wasch-/Pflegemittel nach den Angaben der Wasch-/Pflegemittelhersteller dosieren. Hinweise auf den Verpackungen beachten. Die Dosierung ist abhängig: – von der Verschmutzung der Wäsche, – von der Wäschemenge – vom Härtebereich des Leitungswassers.
Wenn Sie Flüssigwaschmittel verwenden: Flüssigwaschmittel mit von der Waschmittelindustrie angebotenen Dosierbehältern zugeben. Gerät einschalten/Programm wählen 3 Programm mit Programmwähler wählen, z. B. BUNTWÄSCHE/ PFLEGELEICHT. Indem Sie ein Programm wählen, schalten Sie zugleich das Gerät ein. – Das Display leuchtet und zeigt das eingestellte Programm, die aktuelle Uhrzeit sowie das voraussichtliche Programmende an. – Je nach Programm, schlägt der Waschautomat Temperatur und Schleuderdrehzahl vor.
Schleuderdrehzahl ändern/Spülstopp wählen 3 Taste U/MIN. so oft drücken, bis die gewünschte Schleuderdrehzahl bzw. SPÜLSTOPP angezeigt wird. BUNT/ PFLEGELEICHT Programmende um 12.45 14.37 50C 800 aýýýýýaýaýaýaýaýaýaýaýa TEMP. C° TEMP. C° T/MIN. T/MIN. OPTIES OPTIONS OK OK TIJD TEMPS Bei Schleuderdrehzahl „0“ wird am Programmende das letzte Spülwasser abgepumpt, aber die Wäsche nicht geschleudert. • Bei SPÜLSTOPP bleibt die Wäsche im letzten Spülwasser liegen.
3 Wurde zu viel Wäsche eingefüllt, erscheint im Display die Anzeige ÜBERLADEN. In diesem Fall bitte ausreichend Wäsche entnehmen. Eventuell weitere Programmeinstellungen vornehmen. Wenn die Wäsche vor dem Programmstart wieder entnommen wird, kann es vorkommen, dass die Anzeige für die tatsächliche Beladung nicht wieder auf 0 wechselt. In diesem Fall bitte Gerät aus- und nach ca. 3 Sekunden wieder einschalten. Programm neu einstellen und Wäsche wieder einfüllen.
EXTRAS 3 Die unter Extras einstellbaren Sonderfunktionen bleiben dauerhaft im Gerät gespeichert, z. B. Uhrzeit, Sprache, etc. (siehe Kapitel „Extras“), bis sie geändert bzw. abgeschaltet werden. Es werden immer nur die Optionen im Display angezeigt, die mit dem vorher gewählten Programm kombinierbar sind. Vorwäsche, Sensitiv, Flecken, Nachtprogramm 1. Taste OPTION so oft drücken, bis das gewünschte Symbol blinkt, z. B. VORWÄSCHE.
Zeiten einstellen Verkürzte Programme und Aufschub der Startzeit können für ein vorher gewähltes Waschprogramm eingestellt werden. Taste ZEIT drücken. Das Display zeigt die Symbole für ZEIT SPAREN und STARTZEIT-VORWAHL an. ZEIT SPAREN: KURZ oder EXTRA KURZ Verkürztes Programm für leichter verschmutzte Wäsche.
6. Taste ZEIT drücken, wenn keine Startzeitvorwahl eingestellt werden soll. Das Display zeigt das Symbol ZEIT SPAREN sowie die Uhrzeit des Programmendes an. Startzeit-Vorwahl 1. Taste ZEIT so oft drücken, bis Symbol STARTZEIT-VORWAHL blinkt. 2. Taste OK drücken. Im Display wird „Start in 0 min“ angezeigt. 3 3. Taste ZEIT so oft drücken, bis das Display den gewünschten Startaufschub anzeigt, z. B. „Start in 4h“ (=4 Stunden). Unter dem Symbol STARTZEIT-VORWAHL erscheint ein schwarzer Balken.
Ablauf des Programms 3 Das Display zeigt den Programmschritt an, der gerade ausgeführt wird, sowie den Zeitpunkt des Programmendes. BUNT/ PFLEGELEICHT Waschen 12.45 14.37 50C 800 aýýýýýaýaýaýaýaýaýaýaýa TEMP. C° TEMP. C° T/MIN. T/MIN. OPTIES OPTIONS OK OK TIJD TEMPS Der Zeitpunkt des Programmendes kann sich während des Waschvorgangs verändern, da sich das Programm an unterschiedliche Bedingungen beim Waschen anpasst (z. B. Wäscheart und -menge, Unwuchterkennung beim Schleudern, Sonderspülgang etc.
Waschgang beendet/Wäsche entnehmen Am Programmende ertönt 3x ein langer Signalton (bei Einstellung LAUTSTÄRKE NORMAL oder LEISE) und im Display erscheint abwechselnd die Anzeige „Ende“ und „Tür entriegelt“. 1. Einfülltür öffnen und Wäsche entnehmen. 2. Programmwähler auf AUS drehen. 3. Nach dem Waschen die Waschmittelschublade etwas herausziehen, damit sie austrocknen kann. Einfülltür nur anlehnen, damit der Waschautomat auslüften kann.
Memory einstellen Beispiel: Programmplatz MEBUNT/ PFLEGELEICHT 12.45 MORY 1 soll mit folgender 14.37 Programmende um Programmkombination be40C 800 aýýýýýVýaýaýaýaýaýaýaýa legt sein: BUNT/ TEMP. C° T/MIN. OPTIES OK TIJD PFLEGELEICHT 40 °C, 800 U/ TEMP. C° OPTIONS OK TEMPS T/MIN. min, mit VORWÄSCHE. 1. Programmwähler auf BUNTWÄSCHE/PFLEGELEICHT drehen. 2. Taste TEMP. so oft drücken, bis 40 °C im Display erscheint. 3. Taste U/MIN. so oft drücken, bis 800 im Display erscheint. 4.
Lautstärke Die Lautstärke des Signaltons kann gewählt werden. 1. Programmwähler auf beliebiges Programm drehen und Taste OPTION so oft drücken, bis Symbol EXTRAS blinkt. 2. Taste OK drücken. 3. Taste OPTION so oft drücken, bis das Display LAUTSTÄRKE anzeigt. 4. Taste OK drücken. 5. Taste OPTION so oft drüLautstärke cken, bis die gewünschte NORMAL Lautstärke (NORMAL, LEISE, aýýýýýaýaýaýaýBýaýaýaýa AUS) im Display angezeigt TEMP. C° T/MIN. OPTIES OK TIJD wird. TEMP. C° OPTIONS OK TEMPS T/MIN. 6.
Sprache 1. Programmwähler auf beliebiges Programm drehen und Taste OPTION so oft drücken, bis das Symbol EXTRAS blinkt. 2. Taste OK drücken. 3. Taste OPTION so oft drüSprache cken, bis das Display SPRADEUTSCH CHE anzeigt. aýýýýýaýaýaýaýBýaýaýaýa 4. Taste OK drücken. TEMP. C° T/MIN. OPTIES OK TIJD TEMP. C° OPTIONS OK TEMPS T/MIN. 5. Taste OPTION so oft drücken, bis die gewünschte Sprache im Display erscheint, z. B. DEUTSCH. 6. Taste OK drücken. Die Anzeige wechselt zur nächsten Sonderfunktion. 7.
3. Taste OPTION so oft drücken, bis das Display KONTRAST bzw. HELLIGKEIT anzeigt. 4. Taste OK drücken. Kontrast 5. Mit der Taste OPTION die geƒ………………™………………‡ wünschte Einstellung voraýýýýýaýaýaýaýBýaýaýaýa nehmen. Mit jedem TEMP. C° T/MIN. OPTIES OK TIJD Tastendruck oder bei geTEMP. C° OPTIONS OK TEMPS T/MIN. drückter Taste wandert das schwarze Dreieck im Diagramm weiter nach rechts zu mehr Kontrast bzw. mehr Helligkeit. Ist das Dreieck am rechten Rand des Diagramms angelangt, beginnt es wieder von links.
Reinigen und Pflegen Achtung! Keine Möbelpflegemittel oder aggressive Reinigungsmittel zur Reinigung des Gerätes benutzen. Bedienblende und Gehäuse mit einem feuchten Tuch abwischen. Reinigungswaschgang Falls überwiegend mit niedriger Temperatur gewaschen wird, von Zeit zu Zeit ein Kochprogramm durchführen. So werden eventuelle Ablagerungen reduziert und das Gerät wird von innen gereinigt. Waschmittelschublade Die Waschmittelschublade sollte regelmäßig gereinigt werden. 1.
Einfülltür und Gummimanschette Regelmäßig prüfen, ob Ablagerungen oder Fremdkörper in den Falten der Gummimanschette oder innen am Türglas vorhanden sind. Türglas und Gummimanschette regelmäßig reinigen. Was tun, wenn...
Problem Mögliche Ursache Abhilfe Wasserhahn geschlossen. Wasserhahn öffnen. Display zeigt: „Kein Wasserzulauf/Zulauf prüfen“. Waschautomat vibriert während des Betriebs oder steht unruhig. Sieb in der Verschraubung des Zulaufschlauchs verstopft. Wasserhahn schließen. Schlauch abschrauben, Sieb herausnehmen und reinigen. Wasserhahn verkalkt oder defekt. Wasserhahn prüfen, gegebenenfalls reparieren lassen. Transportsicherung nicht Transportsicherung entferentfernt. nen.
Problem Display zeigt: – „Kein Wasserablauf/Ablauf prüfen“ oder – „Pumpe blockiert“. Mögliche Ursache Abhilfe Knick im Ablaufschlauch. Knick entfernen. Maximale Pumphöhe von 1m überschritten. Bitte an den Kundendienst wenden. Gerät ausschalten. Netzstecker ziehen. Laugenpumpe verstopft. Laugenpumpe reinigen. Fremdkörper aus Pumpengehäuse entfernen. Bei Siphonanschluss: SiSiphon reinigen. phon verstopft. Weichspüler nicht eingespült, Fach für Pflegemittel mit Wasser gefüllt.
Wenn das Waschergebnis nicht befriedigend ist Wäsche ist vergraut und in der Trommel lagert sich Kalk ab • Das Waschmittel wurde zu gering dosiert. • Es wurde nicht das richtige Waschmittel eingesetzt. • Spezielle Verschmutzungen wurden nicht vorbehandelt. • Programm oder Temperatur wurden nicht richtig eingestellt. Auf der Wäsche sind graue Flecken • Mit Salben, Fetten oder Ölen verschmutzte Wäsche wurde mit zu wenig Waschmittel gewaschen. • Es wurde mit zu niedriger Temperatur gewaschen.
Notentleerung durchführen 1 Warnung! Waschautomat vor Notentleerung ausschalten und den Netzstecker aus der Steckdose ziehen! Warnung! Die Waschlauge, die aus dem Notentleerungsschlauch ausläuft, kann heiß sein. Verbrühungsgefahr! Vor einer Notentleerung Waschlauge abkühlen lassen! 1. Sockelklappe aufklappen und abziehen. 2. Notentleerungsschlauch herausnehmen. 3. Flaches Auffanggefäß unterstellen. Anschließend Verschlussstopfen durch Drehen gegen den Uhrzeigersinn lösen und herausziehen. 4.
Laugenpumpe 1 Die Laugenpumpe ist wartungsfrei. Das Öffnen des Pumpendeckels ist nur im Störungsfall erforderlich, wenn kein Wasser mehr abgepumpt wird, z. B. bei blockiertem Pumpenrad. Bitte vor dem Einfüllen der Wäsche immer sicherstellen, dass sich keine Fremdkörper in den Taschen oder zwischen der Wäsche befinden. Büroklammern, Nägel etc., die eventuell mit der Wäsche in den Waschautomaten gelangt sind, bleiben im Pumpengehäuse (Fremdkörperfalle, die das Pumpenrad schützt) liegen.
Entsorgung 2 2 1 Verpackungsmaterial Die Verpackungsmaterialien sind umweltverträglich und wiederverwertbar. Die Kunststoffteile sind gekennzeichnet, z. B. >PE<, >PS< etc. Entsorgen Sie die Verpackungsmaterialien entsprechend ihrer Kennzeichnung bei den kommunalen Entsorgungsstellen in den dafür vorgesehenen Sammelbehältern.
Technische Daten 5 Dieses Gerät entspricht den folgenden EG-Richtlinien: – 73/23/EWG vom 19.02.1973 Niederspannungs-Richtlinie – 89/336/EWG vom 03.05.1989 EMV-Richtlinie einschließlich Änderungs-Richtlinie 92/31/EWG – 93/68/EWG vom 22.07.1993 CE-Kennzeichnungs-Richtlinie Höhe x Breite x Tiefe 850 x 598 x 640mm Tiefe bei geöffneter Einfülltür 1017 mm Höhenverstellbarkeit ca. +10/-5mm Füllmenge (programmabhängig) max.
Aufstell- und Anschlussanweisung 1 Sicherheitshinweise für die Installation • Dieser Waschautomat ist nicht unterbaufähig. • Vor Inbetriebnahme das Gerät auf Transportschäden überprüfen. Ein beschädigtes Gerät auf keinen Fall anschließen. Wenden Sie sich im Schadensfall an Ihren Lieferanten. • Vor Inbetriebnahme müssen alle Teile der Transportsicherung entfernt sein. Andernfalls kann es beim Schleudern zu Schäden am Gerät oder an benachbarten Möbeln kommen.
Aufstellung des Gerätes Gerät transportieren 1 Warnung! Der Waschautomat hat ein hohes Gewicht. Verletzungsgefahr! Vorsicht beim Anheben. • Das Gerät nicht auf die Vorderfront und nicht auf die rechte Seite (von vorne gesehen) legen. Elektrische Bauteile können nass werden. • Gerät niemals ohne Transportsicherung transportieren. Transportsicherung erst am Aufstellort entfernen! Transport ohne Transportsicherung kann zu Schäden am Gerät führen.
3. Beide Kunststoffkappen seitlich abziehen. 3 Spezialschlüssel A und Verschlusskappen B (2 Stück) und C (1 Stück) liegen dem Gerät bei. 4. Schraube D inkl. Druckfeder mit Spezialschlüssel A entfernen. 5. Verschlusskappe C gemäß Abbildung umstülpen. 6. Loch mit Verschlusskappe C verschließen. 7. Zwei Schrauben E mit Spezialschlüssel A herausschrauben. 8. Vier Schrauben F mit Spezialschlüssel A herausschrauben. 9. Transportschiene G abnehmen. 10. Die vier Schrauben F wieder einschrauben. 11.
• Bei Standplätzen mit kleinformatigen Fliesen handelsübliche Gummimatte unterlegen. Wenn das Gerät auf einem Sockel stehen soll: Damit das Gerät sicher auf dem Sockel steht, müssen Standbleche*) montiert werden, in die das Gerät eingestellt wird. Wenn das Gerät auf schwingenden Böden stehen soll, z. B. Holzbalkenböden mit Dielenbrettern: Gerät möglichst in einer Ecke des Raumes aufstellen. 1. Eine wasserbeständige Holzplatte (mindestens 15 mm dick) auf mindestens 2 Fußbodenbalken festschrauben. 2.
Elektrischer Anschluss Angaben über Netzspannung, Stromart und die erforderliche Absicherung sind dem Typschild zu entnehmen. Das Typschild ist im Bereich der Einfüllöffnung angebracht. Wasseranschluss Achtung! • Dieses Gerät darf nicht an Warmwasser angeschlossen werden! • Beim Anschluss nur neue Schlauchsätze verwenden! • Gerät nur an die Trinkwasserleitung anschließen. Regen- oder Brauchwasser nur dann verwenden, wenn es die Anforderungen nach DIN1986 und DIN1988 erfüllt.
Wasserzulauf 3 Mitgeliefert wird ein Druckschlauch von 1,5m Länge. Wird ein längerer Zulaufschlauch benötigt, sind ausschließlich Originalschläuche zu verwenden. Der Kundendienst hält Schlauchsätze in verschiedenen Längen bereit. Dichtringe sind entweder in den Muttern der Schlauchverschraubung eingelegt oder im Beipack enthalten. Keine anderen Dichtungen verwenden! Achtung! Alle Schlauchverschraubungen nur von Hand anziehen. 1. Schlauch mit dem abgewinkelten Anschluss an der Maschine anschließen.
Wasserablauf Der Höhenunterschied zwischen Standfläche und Wasserabfluss darf höchstens 1 Meter betragen. Zur Verlängerung dürfen nur Originalschläuche verwendet werden. (Max. 3 m auf dem Fußboden verlegt und dann bis 80 cm hoch). Der Kundendienst führt Ablaufschläuche in verschiedenen Längen. Wasserablauf in einen Siphon Die Verbindungsstelle Tülle/Siphon mit einer Schlauchschelle (im Fachhandel erhältlich) sichern. 1 Wasserablauf in ein Waschbecken/Badewanne Achtung! – Kleine Becken sind nicht geeignet.
Garantiebedingungen Deutschland Der Endabnehmer dieses Gerätes (Verbraucher) hat bei einem Kauf dieses Gerätes von einem Unternehmer (Händler) in Deutschland im Rahmen der Vorschriften über den Verbrauchsgüterkauf gesetzliche Rechte, die durch diese Garantie nicht eingeschränkt werden. Diese Garantie räumt dem Verbraucher also zusätzliche Rechte ein.
Service Wenn Sie einmal unsere Hilfe benötigen, erreichen Sie uns in Deutschland wie folgt: Bei Fragen zu Bedienung oder Ausstattung Ihres Gerätes Wenden Sie sich an den AEG-Direct Info Service: Telefon: 0180 555 4 555 (0,12 Euro/Min)** Internet: www.aeg-electrolux.de E-Mail: aeg-hausgeraete.kundenservice@aeg-hausgeraete.de Bei technischen Störungen Prüfen Sie bitte zunächst, ob Sie mit Hilfe der Gebrauchsanweisung (Kapitel „Was tun, wenn...“) das Problem selbst beheben können.
From the Electrolux Group. The world´s No.1 choice. Die Electrolux-Gruppe ist der weltweit größte Hersteller von gas- und strombetriebenen Geräten für die Küche, zum Reinigen und für Forst und Garten. Jedes Jahr verkauft die Electrolux-Gruppe in über 150 Ländern der Erde über 55 Millionen Produkte (Kühlschränke, Herde, Waschmaschinen, Staubsauger, Motorsägen und Rasenmäher) mit einem Wert von rund 14 Mrd. USD. AEG Hausgeräte GmbH Postfach 1036 D-90327 Nürnberg http://www.aeg-electrolux.